ページ1に含まれる内容の要旨
^
-F<
-r..<
USER'S MANUAT
F<
ATET
- Part2
llt
-
1726 Digital Answering
System with Mailboxes
information
Fold open tbis manual
Oe
for
product's installation and
about tbis
-
Please also read Part 7
operation.
a
ant Pro dact Informa t ion.
Imp ort
(
*D
\7
":q
3
For customer Servrce or Producl
tfi'
\
/
Visit Our Website At
\\ lnformation.
.d
--www.telephonesatlcom
_-, _rB d:
EF{
r- - qts-+-*i dr-ttlf Cdp b.{dY2oc'd.{mcrimTele!'h^nes
Xtlly d t
Cft
€ !(Dl.ldm{AminTelephon6. AIl right
ページ2に含まれる内容の要旨
INSTALLATION Before You Install power cord supplied Choose a location for the answering Use only the with this product. If you need a system ne r a modular telephone and lack replacement, call 1 8O0 222-3llt. a standard electrical outlet not controlled Input: 12OY 6OHz. by a wall switch. Output: 6VAC,35O mA. NOTE: If you do not uant to connect a telepbone, skip Step 2. Table/Desk Installation Modular L Connect the telephone Telepbone line cord. Jack 'rc Standard. Electrical Outlet the Connect
ページ3に含まれる内容の要旨
FEATURE SETUP Press and release Turn System On/Off Funaml orWEttlnEFEM until the s)-stem announces the setting Press to turn the system on or off. loltzorrl you want. Refer the to Feature The message window will display Summary for options. information when the system is on. Press and release lsrrupl to set up the Feature Setup next feature listed on the Feature 1 To enter Feature Setup mode, press and Summary -oR- hold FrruFl until the system announces "Selected announcerrrent is. .." Press
ページ4に含まれる内容の要旨
FEATURESETUP (cont'd) Feature Summary Remote Access Code Change the Remote Access Code to any three digit number from to Do not set to same number 5OO 999. as Priority Calling Code. "Remote . preset access code is..." The RemoteAccess Code, to 5O0, allows you to access many features of this answering phone. system remotely from a touch tone . prompt you repeat 2 The system will to Steps until you have set all and of Feature Setup 3 three digits. to any three-digit Priority Call Code Ch
ページ5に含まれる内容の要旨
FEATURESETUP ,:Qrt: Feature Summary (cont'd) Set the s\'stem to hear callers'messages as they are Call Screening (O\) being recorded or to remain silent while callers (OFF). are recording messages Call Screening is preset to ON. NOTE: Volume be must set to a letel can bear lou to use Call Screening. Review Feature Setup To review the current feature settings. press and release uA. EET .-+- _,-;.--:.
ページ6に含まれる内容の要旨
OPERATION time the message was received. ff Listen To, Save & Delete l'lessages Store Number is set to ON, the system your The system automatically saves also announces the caller's telephone you messages until delete them. You "Store (see number Number"under can store approximately 4O minutes of playing FEATURE SETUP). After the messages, memos, and announcements last message, the system announces (up to a maximum of 119 messages). "End of ntessages." As the system plays messages back i
ページ7に含まれる内容の要旨
OPERATION announcements Set the Clock without making a new recording every You must set time. You can select one the clock once for the announceme nt at a time for system to announce the the system, not correct day and separate announcements for individual time with your messages. A-fter this. if t-ou -Announcement mailhols5 (see Select" in subscribe to Caller ID. the svstem s'ill FEAIIJRE SFILT). Announcements automaticalh'reset the clock each time fr, b, and f are used when you new call
ページ8に含まれる内容の要旨
OPERATION Answering Calls Record a ilemo When you ve selected annormcement 8, b, You can record a memo up to three or f, and the system answers a call, the minutes long to be stored as an incoming caller hears the announcement you message. recorded, followed by a beep. During the 1 Press and release WEMIdEPEfl. Press the announcement, callers can pfess I,2,or 3 MBOX button where you want the to select a mailbox, or they can wait for memo to be stored. When the system the beep to leave a mes
ページ9に含まれる内容の要旨
r I REMOTE OPERATION Connect with the Answering System You can access many features remotely continues to play after entering your a touch tone phone. from code,wait for the announcement to end press or to stop the announcement, 1 Dial your telephone number. @ then reenter the code. 2 When the system answefs, youf enter To use a remote access command 3 three-digit RemoteAccess Code during press during message after the announcement. @elow), @ or The system playback and wait for the two-be
ページ10に含まれる内容の要旨
IN CASE OF DIFFICULTY If you have difficulty operating this System Does Not Respond To Remote product, try the suggestions below. Commands For Customer Service, visit our website . you Make sure are calling from a touch at u)uxa. te lep b one s. att. com or call phone you tone . When dial a number, 1 8OO 222-31 1 1. Please retain your you should hear tones. Ifyou hear receipt as your proofofpurchase. phone clicks instead, the is not a touch tone telephone. Messages Are Incomplete . The
ページ11に含まれる内容の要旨
OF DIFFICULTY CASE IN Power Failure Recovery ls Blank l'lessage Window fromAC system is disconnect€d If the . power cord is securely Make sure the Your power it will not operate. (and threaded through the connected are retained announcement and messages tab) to both the answering strain relief you power failure but in memory during a an electrical outlet not system and See the will need to reset the clock. a wall switch. controlled by il of the unit. instructions on the bottom .
