ページ1に含まれる内容の要旨
Part Number: V983492
Vinyl Windows and Doors
© 2010 Pella Corporation
V983492
INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION
350 SERIES O,OX/XO SLIDINg PATIO DOOR
WITh fIXED PANEL INSTALLED
Lea las instrucciones en español en el reverso.
Table Of Contents
Installation Instruction Information ...........................................................................................Page-1
Exploded View of Installation and Parts List .....................................................
ページ2に含まれる内容の要旨
SEALANT SEALANT REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT. Head Nailing Fin Corner Top Water Flashing Flashing Resistive Tape Tape Barrier Corner Side Flashing Sheathing Flashing Tape Tape Framing Wood Blocking Sill Sill Flashing Tape #1 Side Flashing Tape Sill Flashing Tape #2 Head Concrete block Wood Blocking Sill Sill Flashing Tape #1 Sill Flashing Tape #2 Always read the Vinyl Window and Door Limited Warranty before purchasing or installing Vinyl Windows and Doors manufa
ページ3に含まれる内容の要旨
1" 6" Interior Interior Exterior 1 ROUGH OPENING PREPARATION If replacing an Aluminum sliding door in hardcoat stucco, see Step 8 flush flange Opening Preparation on page 11. A. Confirm the opening is plumb and level. Ensure the bottom of the rough opening does not slope toward the interior. Note: For peak water performance it is critical the 1A bottom be level within +/- 1/16". B. Confirm the door will fit the opening. Measure all four sides of the opening to make sure it is 1/2" large
ページ4に含まれる内容の要旨
1 ROUGH OPENING PREPARATION (CONTINUED) G. Apply sill flashing tape #2. Cut a piece of flashing tape 12" longer than the opening width. Apply at the bottom, overlapping tape #1 by at least 1". DO NOT allow the tape to 1G extend past the interior face of the framing (1G). Note: The flashing tape does not need to extend all the way to the interior of the framing. If using optional sill pan, see Step 10 Sill Pan fabrication and Installation on page 15. 2 PREPARE THE DOOR FOR INSTALLATION TW
ページ5に含まれる内容の要旨
12" Exterior Interior 3 SETTING AND FASTENING THE DOOR (CONTINUED) B. Dry fit the door. Make sure the door is plumb, square and level. Drill anchor locations with 1/8" masonry bit. Mark the interior of the door frame at the sill to show a 3C boundary for sealant placement. Carefully remove and set the door aside. C. Apply two continuous 1/4" to 3/8" diameter beads of sealant across the sill of the opening and 12" up the jambs, towards the interior side of the door (between the anchor ho
ページ6に含まれる内容の要旨
3 SETTING AND FASTENING THE DOOR (CONTINUED) F. fasten the door to the opening: Door frames with Nail fin Only: Insert one 2" galvanized roofing nail into every other pre-punched hole in the nailing fin. All f rame Types: Transom/Sidelight: Remove the sill track and pocket covers by pulling on the paper ring. head and Jambs: At each pre-drilled installation hole, drill 1/8" pilot holes through the outer frame wall, shims and the rough opening. Drive #10 x 2" corrosion resistant pan
ページ7に含まれる内容の要旨
3 SETTING AND FASTENING THE DOOR (CONTINUED) 2-PANEL (OX) EXTERIOR J. Install jamb pocket cover in pocket above bumper. Fixed Panel 2-PANEL (XO) EXTERIOR 3-PANEL (OXO) 4-PANEL (OXXO) EXTERIOR EXTERIOR POCKET COVER POCKET LOCK KEEPER LOCK KEEPER A A Fixed COVER S S Panel INTERIOR T T LOCK KEEPER R R A A K. Install the lock keeper/strike. Position the keeper/ G Vent G Vent Vent Vent A Panel A Panel Panel strike at the pre-drilled pilot holes. Insert a shim between Panel L
ページ8に含まれる内容の要旨
1" Exterior Exterior Exterior Interior INTEGRATING THE DOOR TO THE 5 WATER RESISTIVE BARRIER A. Apply the side flashing tape. Cut two pieces of flashing tape 4" longer than the frame height of the door. Apply one piece to each side over the nailing fin and onto the water resistive barrier. The tape should extend 2" above 5A the top of the door and 2" below the bottom of the door. Press the tape down firmly. B. Apply the top flashing tape. Cut a piece of flashing tape long enough to go
ページ9に含まれる内容の要旨
6 INTERIOR SEAL (CONTINUED) B. On the interior, seal the door sill to the floor with a corner bead of sealant. Connect this bead of sealant to the insulating foam at both door jambs. C. Check the door operation by opening and closing the door. Note: If the door does not operate correctly, check to make sure it is still plumb, level, square and the sides are not bowed. If adjustments are required, remove the foam with a serrated knife. Adjust the shims, and reapply the insulating foam sealan
ページ10に含まれる内容の要旨
SEALING THE DOOR TO THE EXTERIOR 7 WALL CLADDING (CONTINUED) NAIL-fIN fRAME AND REPLACEMENT fRAME: A. Insert closed cell foam backer rod into the space around the door approximately 1/2". This should provide at least a 1/2" clearance between the backer rod and the exterior face of the door. 7A B. Apply a bead of high quality exterior grade sealant to the entire perimeter of the door. On doors where the bottom fin has been removed, insert sealant into the spaces between the 7B bottom of
ページ11に含まれる内容の要旨
FLUSH FLANGE OPENING PREPARATATION 8 Installation Instructions for Replacement of Aluminum Sliding Doors in Hard Coat Stucco Applications. These instructions are designed for typical California hard coat stucco exterior applications. The installation must leave the existing aluminum sliding door frame and weep system in place. These instructions are not to be used with any other construction method and rely on the integrity of the existing aluminum sliding door frame and flashing system. B
ページ12に含まれる内容の要旨
FLUSH FLANGE OPENING PREPARTATION 8 (CONTINUED) H. Install the wood blocking in the head existing door frame. Place a 3/16" bead of sealant in the door panel cavities, then insert the wood blocking into the head cavities. Next insert the wood blocking into the jamb panel cavities of the existing door frame. I. Construct a door sill pan for the door. Measure the distance between the cut ends of the existing door sill and add 2". Measure 1" from each end and cut through the vertical leg of th
ページ13に含まれる内容の要旨
FLUSH FLANGE OPENING PREPARTATION 8 (CONTINUED) O. Using a pencil, mark the interior and exterior Sealant Placement, arrows indicate edges of the sill pan on the sill of the rough sealant locations. opening. Remove the door and sill pan. P. Place a 1/4" diameter bead of sealant in the 8O following locations: 8P - The exterior side of the interior pencil mark. - The interior side of the exterior pencil mark. - Midway be tween t he e xterior and in terior sealant beads. Q. Place a
ページ14に含まれる内容の要旨
Exterior View Exterior View SETTINg AND fASTENINg ThE DOOR IN fLUS h fLANgE 9 APPLICATIONS (CONTINUED) B. Place a 1/4" diameter continuous bead of sealant on the face of the existing door frame jambs and head. C. from the exterior, set the door into the opening. Set the sill of the door onto the sill pan and tilt the door into position, centering it in the opening. DO NOT slide the door on the sill pan. 9B 9C D. Insert shims between the door and the sides of the opening at the top two ancho
ページ15に含まれる内容の要旨
Interior View SETTINg AND fASTENINg ThE DOOR IN fLUS h fLANgE 9 APPLICATIONS (CONTINUED) G. Plumb and square the door. Insert shims between the new door frame and the existing door frame at the pre-drilled anchor hole locations in the door jambs. DO NOT ShIM ThE hEAD UNTIL ALL fIXED PANELS ARE INSTALLED. Move the door in the opening until the flanges are tight 9G against the existing aluminum door frame. Note: DO NOT over shim. H. Drill a 1/8" pilot hole through the door frame, shims,
ページ16に含まれる内容の要旨
OPTIONAL SILL PAN fABRICATION 10 AND INSTALLATION (CONTINUED) Install the sill pan into the opening, aligning the interior and exterior edges with the pencil marks Sealant between the from previous illustration. Press down on the sill pan back and side legs of sill pan to seal it into the opening. Leave gap at each Place one 1/4” diameter bead of sealant in the end of sealant lines following locations: - In the bend at the back of the sill pan. - 1/2” from the exterior edge of the si
