ページ1に含まれる内容の要旨
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
CLASSIFIED PER EN/IEC 60825-1:2007
Complies with FDA performance standards
for laser products except for deviations
pursuant to Laser Notice No. 50, dated
June 24, 2007.
User Manual
ページ2に含まれる内容の要旨
TABLE OF CONTENTS 1. Before You Begin ..................................................................................................................................................... 3 What Is Included ........................................................................................................................................................ 3 Unpacking Instructions ..............................................................................................................
ページ3に含まれる内容の要旨
1. BEFORE YOU BEGIN What Is Included 1 x MiN™ Laser FX 2.0/RGX 2.0 1 x Power supply 1 x Flexible tripod 1 x Clamp adaptor 1 x Adjustable stand 1 x Warranty card 1 x Wireless remote 1 x User manual Unpacking Instructions Immediately upon receipt, carefully unpack this product and check the container to make sure you have received all the parts indicated above in good condition. Claims If the container or the material inside the container (this product
ページ4に含まれる内容の要旨
Safety Instructions Please read the following notes carefully because they include important safety information about the installation, usage, and maintenance of this product. Keep this User Manual for future consultation. If you sell this product to another user, be sure that they also receive this document. Always make sure that the voltage of the outlet to which you are connecting this product is within the range stated on the decal or rear panel of the product. Thi
ページ5に含まれる内容の要旨
Non Interlocked Housing Warning This unit contains high power laser devices internally. Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation. The laser power levels, accessible if the unit is opened, can cause instant blindness, skin burns, and fires. Laser Safety Notes STOP AND READ ALL THE LASER SAFETY NOTES BELOW Laser Light is different from any other light sources with which you may be familiar. The light from this produc
ページ6に含まれる内容の要旨
Laser Safety Label Reproduction Top Front Rear Bottom MinLasers 2.0 User Manual 6 August 2011
ページ7に含まれる内容の要旨
LASER EXPOSURE Laser light - Avoid direct eye contact! Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard “For Safe Use of Lasers”, available from the Laser Institute of America: www.laserinstitute.org. Many local governments, corporations, agencies, military and others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser Display guidance can be obtained via the International Laser Display Association:
ページ8に含まれる内容の要旨
2. INTRODUCTION Product Overview Mode Button Microphone Wireless Remote Receiver LED Indicator Laser Output Green Laser Dimmer 12 V Power In Cooling Fan MinLasers 2.0 User Manual 8 August 2011
ページ9に含まれる内容の要旨
3. SETUP AC Power This product includes an external power supply which is auto-ranging and runs on 100~240 VAC, 50/60 Hz power. Only use the included power supply! To obtain a replacement power supply, contact Chauvet®. To determine the power requirements for a particular product, see the label affixed to the Power Supply back plate of the product or refer to the product’s specifications chart. A product’s listed current rating indicates its average current draw under normal
ページ10に含まれる内容の要旨
Floor Stand, Flexible Feet (3) Coupler Clamp MinLasers 2.0 User Manual 10 August 2011
ページ11に含まれる内容の要旨
Proper Usage This product is for overhead mounting only. For safety purposes, CHAUVET® recommends mounting your lighting effect products on steady elevated platforms or sturdy overhead supports using suitable hanging clamps. In all cases, you must use safety cables. You can obtain appropriate mounting hardware from your lighting vendor. International laser safety regulations require that laser products must be operated in the fashion illustrated below, with a minimum of 3 meters (
ページ12に含まれる内容の要旨
4. OPERATING INSTRUCTIONS Manual Mode Access the four different operating modes available in this product by using the button on the front panel. Pressing and holding the button for 2.5 seconds will turn the product on or off. Press to cycle through the modes. Please see a description of each mode below. Mode Description 1 Sound-active A 2 Sound-active B 3 Automatic A (fast effects) 4 Automatic B (slow effects) The LED indicator on the
ページ13に含まれる内容の要旨
5. APPENDIX General Troubleshooting SYMPTOM POSSIBLE CAUSE(S)POSSIBLE ACTION(S) Check total load placed on the Excessive circuit load electrical circuit. Breaker/Fuse keeps blowing Short circuit along the power Check for a short in the electrical wires wiring (internal and/or external). No power Check for power on Mains. Device does not power up Loose power cord Check power cord Check Control Panel and unit Wrong DMX addressing addressing Damaged D
ページ14に含まれる内容の要旨
Product Maintenance Dust build up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life and mechanical wear. To maintain optimum performance and minimize wear, you should clean your lighting products at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency. To clean this lighting product, follow the instructions below: 1. Unplug the p
ページ15に含まれる内容の要旨
Returns Procedure The user must send the merchandise prepaid, in the original box, and with its original packing and accessories. CHAUVET® will not issue call tags. Call CHAUVET® and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. The user must clearly label the package with a Return Merchandise Authorization (RMA) number. CHAUVET® will
ページ16に含まれる内容の要旨
6. TECHNICAL SPECIFICATIONS Dimensions and Length Width Height Weight Weight 4.3 in (111 mm) 3.3 in (85 mm) 1.8 in (45 mm) 0.7 lbs (0.3 kg) Note: Dimensions in inches rounded to the nearest decimal digit Power Input Voltage Range Voltage Selection 12 VDC 600 ma 100~240 V, 50/60 Hz Auto-ranging Parameter 120 V, 60 Hz 230 V, 50 Hz Energy consumption 6 W 6 W Power Supply Operating current (units) 0.1A 0.1 A Power I/O Input Output Connectors IEC Edison (USA) Cord
