ページ1に含まれる内容の要旨
eDVR Installation Guide
MD3200M
(v 1.0)
ページ2に含まれる内容の要旨
Caution Since this device is operation purpose and registered as suitable electromagnetic waves, seller or user should be cautios on this point. If the device is sold or purchased wrongly, it is required to replace as Home use. FCC Compliance Statement Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment. NOTE : This equipment has been tested and found t
ページ3に含まれる内容の要旨
Important Notice 1. Do not place heavy objects on the top of the eDVR 2. eDVR is for indoor use. It is not weatherproof. Use eDVR with referring to its environmental specifications (Temperature & Humidity). To clean the eDVR, gently wipe the outside with a clean dry cloth. 3. eDVR use AC power of 110V~240V. Be cautions not to cause electric damages to eDVR. 4. Becareful not to drop the eDVR. Physical shocks may harm the products including internal HDD. In addition, be sure the eDVR is secured af
ページ4に含まれる内容の要旨
Contents OVERVIEW .................................................................................................................................. 7 1. What is MD3200M?.............................................................................................................. 7 2. Supplied accessories.............................................................................................................. 8 3. Description & Function .......................................................
ページ5に含まれる内容の要旨
8.2.7. Apply Date/Time .................................................................................................. 22 8.3. Setting recording condition........................................................................................... 23 8.3.1. Configuration Status ............................................................................................. 23 8.3.2. Recording Speed/Quality....................................................................................... 24 8.
ページ6に含まれる内容の要旨
12. Using Control Center Lite ................................................................................................ 42 12.1. Starting.................................................................................................................... 42 12.1.1. PC system requirements for running Control Center Lite.......................................... 42 12.2. Installing Control Center Lite .................................................................................... 42 12.
ページ7に含まれる内容の要旨
OVERVIEW 1. What is MD3200M? The eDVR MD3200M is a 16-analog channels network digital video recorder. Video, Audio, Text and Event-Logs are digitized and stored on two internal Hard-Drives □ 32 analog video channels □ 4 channel two-way audio recording & playback 1 □ Max. 480ips at 4CIF recording 2 □ Real-time (60fps for each channel) monitoring □ Built-in software multiplexer for all live monitoring channels (1/4/9/16/ch Mode on CCTV Monitor) □ Maximum 8TB storage capacity (IEEE 1394 for externa
ページ8に含まれる内容の要旨
2. Supplied accessories Unpack and check all the items as below; 1. eDVR MD3200M (1EA) 2. AC Power Cord (1EA) 3. CD (Including Software) (1EA) 4. Remote Controller (1EA) 5. RACK FIXING KIT (1SET) 6. R-HDD screw (8EA) Attention for the system without HDD installed In case of system without HDD, HDD only can only be installed in R-HDD(Removable Hard disk rack). For the internal installation of HDD additionally, For the details, please contact to local distributor. 8
ページ9に含まれる内容の要旨
3. Description & Function MD3200M front (1) Power switch (2) Function buttons (3) LED (4) USB port (5) Remote controller receiver (6) CD/DVD-RW ROM (7),(8) Built-in Hard Disk Rack 9
ページ10に含まれる内容の要旨
MD3200M rear (9) AC power connector (10) BNC connector for video input (11) Terminal block for sensor, relay, and serial input/output (12) RS232 connector (13) VGA connector (14) IEEE1394 connector (15) eSATA connector (16) Network Storage connector(RJ45) (17) GND (18) Ethernet connector (19) Audio input/ output connector (20) BNC connector for monitor output 10
ページ11に含まれる内容の要旨
INSTALLATION AND CONNECTION 4. Connecting & Running 4.1. Connecting camera (1) Connect CCTV camera to MD3200M with BNC cable as below. 1. The video type for all channels should be either NTSC or PAL, not be combined both. 2. MD3200M sets video signal’s impedance (75 Ω ) automatically. 75-Ohm termination register is always connected on video input, and can't be removed. So MD3200M's video input must be a terminal of the connection. 3. Video Type(NTSC/PAL) should be changed after opeting MD
ページ12に含まれる内容の要旨
Monitor out put of MD3200M is separated as A(Normal) and B(Spot). Connect to Monitor A if only one Monitor is used . Monitor output is fixed depend on channel. Video Out 1, 3 is output channel 1 to 16, and Video 2, 4 is output channel 17~32. 4.3. Connecting Audio (1) Connect auto signal to MD3200M with using RCA cable. 12
ページ13に含まれる内容の要旨
4.4. Supplying power (1) Connect power cable as shown below 1. When supplying power, MD3200M starts booting automatically. 2. In order to cut off power, press the power switch on MD3200M front during 4 seconds and enter admin password after appearing a pop window. 3. For supplying again, push the power switch. 13
ページ14に含まれる内容の要旨
5. Running OSD menu 5.1. Using menu Press the [MENU] in keypad of front to open the OSD Configuration Menu ① Main Menu ② Sub-menu ③ Setting Page (1) Main Menu : The selected tab is shown in blue and the related sub-menu will be shown below the tab. To movo to the previous/next Main Menu tab, use the [ ◀/ ▶] arrow buttons. To move to a sub-menu, press the [ ▷]/[▼ ] arrow buttons. (2) Sub-menu : The selected sub-menu is shown in blue and the relaed setting will be shown the right of the sub-menu.
ページ15に含まれる内容の要旨
5.2. Dialogue box to edit a word There are two methods to input a word.. (1) Entering words Move pressing [ ▶] arrow button to enter next word until the word is looking for is shown using [▲ /▼ ] arrow buttons. In case of spacing words, press [ ▶] to move one space and enter the word. To exit the Dialogue box, press the [ ▷] arrow button. (2) Available words range to use 1 2 3 4 5 6 7 8 9 0 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z (
ページ16に含まれる内容の要旨
6. Setting remote controller When controlling several eDVRs with one remote controller, set Remote Contorl ID as follows. 6.1. Setting ID of MD3200M (1) Press the [MENU] button (2) Select “System” with using [ ▶] button and press the [ ▷] or [▼ ] button (3) Select “Miscelleaneous” from the sub-menu list using the button[▼ ] and press [ ▷] button. (4) Select “Remote Control ID” and press the [ ▷]. (5) Select a value using the [ ◀/ ▶] buttons and press the [EXIT] button. (6) Press the [EXIT] butto
ページ17に含まれる内容の要旨
6.2. Selecting MD3200M If several eDVRs are set with unique ID numbers, they can be controlled with one remote controller. To select a specific eDVR (MD3200M), Keep pressing the ID button of remote controller until a buzzer sounds during 2 seconds. Because remote controller ID is sixteen, eDVR will correspond until pressing ID button sixteen times. 6.3. Operable range of remote controller 6.4. Loading the batteries into remote controller Remote Controller requires two AAA-type batteries 2
ページ18に含まれる内容の要旨
7. MD3200M configuration 7.1. Basic configuration 7.2. Advanced configuration 18
ページ19に含まれる内容の要旨
7.3. External storage & Back up configuration 7.4. Internet/ Intranet configuration 19
ページ20に含まれる内容の要旨
8. eDVR MD3200M basic setting 8.1. Viewing Image When power is on, MD3200M starts automatically and images are displayed in basic 16ch-split screen after the booting. If user password is set, a prompt for entering the password will appear. Facotry default is reserved as not responding key pad on eDVR front (It is not set from factory default) 20
