ページ1に含まれる内容の要旨
Bluetooth Handsfree
Bluetooth Handsfree
C Ca ar r K Kiit t w wiit th h L LC CD D D Diis sp plla ay y
User’s Manual
Model: BT-390
ページ2に含まれる内容の要旨
Contents Bluetooth Handsfree Car Kit with LCD Display················ 3 1. Introduction·································································· 1 Identifying Components······················································ 1 2. Installation ··································································· 3 Installing the Junction Box·················································· 3 Connecting the Power Supply ············································ 4 Connecting
ページ3に含まれる内容の要旨
Display Settings·································································· 20 Adjusting Display Contrast····························································· 20 Adjusting Display Brightness·························································· 21 Changing the Backlight Color························································· 21 Enabling Auto Dim Screen····························································· 22 Other Settings································
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
1. Introduction Carefully unpack the BT-390 Bluetooth Handsfree Car Kit and check that the following items are included: Identifying Components Unpack the Car Kit package and ensure the following items are included. Remote / Bracket / Clasp / BT-390 LCD Junction Box CR2032 Battery Part # 31132450 Part # 31132100 Part # 31132000 Stand Speaker Microphone Part # 31132060 Part # 31132430 Part # 31132440 Fuse Set Power Cable Part # 31132010 Part # 31132
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
2. Installation This section demonstrates how to set up and install the BT- 390 into a vehicle. Installing the Junction Box The Car Kit is designed to work with the 12/ 24-volt power supply of the vehicle. Refer to the following to install the junction box in a vehicle. 1. Locate a suitable place inside the car to mount the junction box. Select a dry place that avoids excessive heat and mechanical vibration. Ideally, the junction box should be hidden from view, but still easily acces
ページ8に含まれる内容の要旨
2. Installation Connecting the Power Supply (For Options 1 and 2 only) The following illustration demonstrates how to connect the Car Kit’s power cables to the vehicle’s electrical system. Important: The blue cable must be connected to the 12/ 24V switched to enable the Car Kit to go into standby mode. Do not connect the blue cable to the +12/ 24V constant. Doing so may discharge the battery of the vehicle and prevent the Car Kit from being reset. 4
ページ9に含まれる内容の要旨
2. Installation Connecting Components The following illustration shows where to connect the components. Item Description The caller ID should be placed on the dash within view of the driver and passenger. Caller ID (See Installing the Caller ID Display on page 9.) Ideally, the microphone should be located in Microphone front of the user and above waist height. For best reception, the speaker should be Speaker mounted at least 80cm (30 inches) from the Car Kit’s microphone.
ページ10に含まれる内容の要旨
2. Installation Preparing the remote control The control module is designed to attach to the inside of the steering wheel on the left or right side. Installing the battery Before attaching the control module, install the supplied battery. 1. Remove the battery cover from the rear of the control module. 2. Insert the new battery with the correct polarity as shown below. 3. Put the battery cover back on. + 6
ページ11に含まれる内容の要旨
2. Installation Attaching the remote control Refer to the following to attach the control module: 1. Attach the rubber clasp to the two notches on one side of the bracket base. 2. Pull tightly on the rubber clasp by holding it firmly from the middle and position the bracket base on the inside of the steering wheel. 3. Wrap the rubber clasp tightly around the steering wheel and secure it on the other two notches on the bracket base. 7
ページ12に含まれる内容の要旨
2. Installation 4. Attach the bracket cover with the two supplied hex bolts. 5. Slide the control module into the module bracket as shown. (To remove the control module, push the release button to the right and remove the control module.) 6. Now the remote is attached to the wheel. 8
ページ13に含まれる内容の要旨
2. Installation Installing the Caller ID Display The caller ID is designed to sit on the dashboard or other location. Once it is attached to the stand remove the adhesive cover from the sticker pad (attached) from the base and press firmly to secure in place. If you wish to attach the LCD display elsewhere, such as next to the car radio, detach the base from the stand by removing the screw as demonstrated. Turn the stand inwards and apply a sticker pad (provided) to the back o
ページ14に含まれる内容の要旨
2. Installation Installing the Microphone Before installing the microphone, take note of the following: Make sure that the cable can reach from the microphone to the speaker. If the cable is too short, relocate the microphone. Do not lengthen the cable. The supplied microphone is uni-directional. For best results, place the microphone in front of the person talking. It has a reception angle of 60 degrees, and is most effective within a 60-cm radius. Installing the Microphone Find a
ページ15に含まれる内容の要旨
3. Operation How to Operate the Car Kit Understanding the icons on your screen and remote control Please see below for the explanations of the icons on the main screen. 11
ページ16に含まれる内容の要旨
3. Operation Basic operation Connecting to the Mobile Phone for the First Time As soon as the ignition is turned on “BT-390” text will be displayed on the backlit screen and it will quickly enter the “Pairing” mode searching for available Bluetooth mobile phones for pairing up. If the pairing screen does not display automatically, turn on this function manually (See Connection Settings on page 18). Pairing BT-390 Switch on mobile phone’s Bluetooth connection and conduct a s
ページ17に含まれる内容の要旨
3. Operation Dialing the First Call Scroll down to enter main menu and go to Dial Number then press the Enter button. Scroll up/down to go to your desired number, press Enter to select the number. Phone Book 1 2 3 4 5 6 7 8 Call History Dial Number 0286655757 Settings Once you have finished selecting all the numbers required, press Answer to call the complete telephone number you have just entered. Receiving and Ending a Phone Call When there is an incoming call, press the A
ページ18に含まれる内容の要旨
3. Operation There are a number of ways to upload your phonebook to the BT-390, if your mobile phone supports automatic phonebook synchronization (for example, Nokia 6230i), it will upload call history, phone book entries, and sort the phone book as soon as the phone is connected with the car kit. Note: Phonebook synchronization and sorting time may differ depending on size of phonebook list and also the phone’s transfer speed. This may also affect the initial remote control response
ページ19に含まれる内容の要旨
3. Operation Name & Numbers Sync Phone Book Receive Contact Back Note: Contacts are picked up in random order by the car kit; therefore, BT-390 will perform the sorting function in the background after the sync. If you access the phonebook before the sorting is completed, you may see that some contacts are not displayed in right order. This is normal for the first time sync and please waits until the sorting process is completed before accessing the phonebook. However, if your phon
ページ20に含まれる内容の要旨
3. Operation screen will display the contact received. Repeat the process for other entries if necessary. Once you have finished, press the Reject/End button to stop OPP mode and re- establish the Bluetooth link with your mobile phone. Note: Some phones support sending multiple contacts in one operation under the OPP mode (such as Mark all function in Nokia). It is recommended that no more than one hundred selections be sent at a time. Phonebook Functions 2 – Search for a Name to Call
