ページ1に含まれる内容の要旨
Tracer 2000 Digital Video Recorder
User’s Manual
ページ2に含まれる内容の要旨
Tracer 2000 DVR user manual Contents CHAPTER I INTRODUCTION...............................................................................................................5 LIMITED WARRANTY ...............................................................................................................................5 FUNCTION INTRODUCTION ..........................................................................................................
ページ3に含まれる内容の要旨
Tracer 2000 DVR user manual 1. Standard CMOS Features ....................................................................................................................24 2. Advanced BIOS Features .....................................................................................................................25 3. Advanced Chipset Features..................................................................................................................26 4. Integrated Peripherals.....
ページ4に含まれる内容の要旨
Tracer 2000 DVR user manual Copyright Notice Copyright 2004. All Rights Reserved This document may not, in whole or in part, be reproduced or transmitted in any form or by means, electronic, mechanical, or optical, including photocopying, recording, or storing in a retrieval system, or translated into any language in any form without the prior written content of us. Warranties We make no warranties with respect to this documentation and disclaim any implied warranties of mercha
ページ5に含まれる内容の要旨
Tracer 2000 DVR user manual CHAPTER I INTRODUCTION Thank you for purchasing Tracer 2000 DVR; this manual will guide you through the setup, installation, and use of all our DVR systems. Before proceeding, please read this manual thoroughly! If you have any questions or concerns that cannot be solved by following this manual, please visit our web site at http://www.giantec.net LIMITED WARRANTY Giantec Inc. warrants this product to be in compliance with its own plan
ページ6に含まれる内容の要旨
Tracer 2000 DVR user manual FEATURE The TRACER2000 comes with the following hardware devices: Control panel with IR receiver One10/100Mbps RJ-45 Ethernet Port One RS 232 and one RS232/422/485 selectable interface One VGA Connector One speaker out Two USB Ports Two 3.5” HDD Supported Four Audio-in Ports Eight GPIO Ports Remote Commander Working temperature: 0 ~ 45 °C Storage temperature: -10 ~ 65 °C Relative humidity: Maximum 85%, non-condensing Power requirement: AC
ページ7に含まれる内容の要旨
Tracer 2000 DVR user manual CHAPTER II PACKAGE Packing List Check the accessories accompany with the system you purchase as listed below. With newer package release, the accessories are compacted into an accessory box. Please check the items and Contact to your dealer you bought from if any of them is missing TRACER2000 System Power Cord Screws Pack Remote Commander Battery (AAA) X 2 User’s Manual Installation CD-ROM Please keep the packaging materials.
ページ8に含まれる内容の要旨
Tracer 2000 DVR user manual CHAPTER III INSTALLATION FRONT PANEL VIEW Confirm Alarm Menu Display Playback IR UP Removable Air Removable Air LEFT RIGHT Filter Bracket Filter Bracket DOWN Remove and clean up Air Filters monthly is essential. REAR PANEL VIEW Power supply Parallel port GPIO Audio BNC connector MIC and Speaker COM1 VGA USB Ports x 2 COM2 10/100 Ethernet Version 3.0
ページ9に含まれる内容の要旨
Tracer 2000 DVR user manual 1 INDICATOR Power LED Power LED: Green light shows power is on. Status LED: Green light continuous on means working properly. Status LED Green light blinking shows status of recording Red light continuous on means no signal (This may implies HDD damaged, No Power, or Access Error.) Red light blinking shows status of recycling. (HDD space less than 1 Gigabyte) 2 CABLE CONNECTION Following is the basic device must be prepared before
ページ10に含まれる内容の要旨
Tracer 2000 DVR user manual 2.2. Connect Camera Cable to BNC connector 2.3. Connect to LAN connector: Plug RJ-45 connector to LAN Port 2.5.1 Insert RJ-45 cable to network LAN socket on the rear. 2.5.2 Connect Serial port modem to serial connector (COM1) and through Dial-in function to connect to Internet. Version 3.0 Page 10 of 36
ページ11に含まれる内容の要旨
Tracer 2000 DVR user manual 2.4. Connect to Printer Port (option) There are two types of Printer port. One is LPT the other is USB. Connect Port as show below: USB Port Version 3.0 Page 11 of 36
ページ12に含まれる内容の要旨
Tracer 2000 DVR user manual 3. POWER CONNECTOR 3.1. Connect power cord (110V~240V auto switch) into the power socket. Press “I” to start up system... Pushes switch “I” to turn it on. Version 3.0 Page 12 of 36
ページ13に含まれる内容の要旨
Tracer 2000 DVR user manual CHAPTER IV Pin assignment Internal Jumpers and Connectors Version 3.0 Page 13 of 36
ページ14に含まれる内容の要旨
Tracer 2000 DVR user manual Power Switch for ATX power supply (JP1) Signals JP1 Power ON/OFF 1-3 Reset/LED/Speaker (JP1) Signals JP1 Power LED, Pin 9+, Pin10- 9-10 External speaker 14-20 HDD LED, Pin8+, Pin7- 7-8 System reset switch 5-6 SUSLED Pin4+, Pin2- 2-4 PS. For the AT system (short pin 10 & pin12) for power on Internal USB connector (USB2) Signals USB2-1 USB2-2 Power 1 10 Data - 3 8 Data + 5 6 USB GND 7 4 CHS GND 9 2 Power connector (P1) Signal
ページ15に含まれる内容の要旨
Tracer 2000 DVR user manual CPU FSB Select (JP4) Function JP4 Auto by CPU 1-3, 2-4 66 MHz 3-5, 4-6 FAN control (FAN1, 2) Function FAN1,2 Sense 3 +12V 2 PWM control 1 HDD Connector (IDE1, 2) 39 1 40 2 Pin no. Signal Pin no. Signal 1 - RST 2 GND 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 GND 20 N.C. 21 N.C. 22 GND 23 IOW 24 GND 25 IOR 26
ページ16に含まれる内容の要旨
Tracer 2000 DVR user manual Parallel/Printer connector (PRN) Pin no. Signal Pin no. Signal 1 Strobe 10 -Acknowledge 2 Data 0 11 Busy 3 Data 1 12 Paper Empty 4 Data 2 13 + Select 5 Data 3 14 - Auto Feed 6 Data 4 15 - Error 7 Data 5 16 - INIT Printer 8 Data 6 17 - Select Input 9 Data 7 18-25 Ground Video Input (J2) 43 1 2 44 Pin no. signals Pin no. signals 1 VCC 2 V-I-OE00 3 GND 4 V-I-OE01 5 VIN00 6 V-I-OE02 7 VIN01 8 V-I-OE03
ページ17に含まれる内容の要旨
Tracer 2000 DVR user manual General Purpose Input / Output (J3) 2 16 1 15 Pin no. signals Pin no. signals Audio IN3 1 GPIO-0 2 3 GPIO-1 4 AGND 5 GPIO-2 6 Audio IN2 AGND 7 GPIO-3 8 9 GPIO-4 10 Audio IN1 11 GPIO-5 12 AGND Audio IN0 13 GPIO-6 14 15 GPIO-7 16 GND(for GPIO) Infra-Red (IR) Pin no. signals 1 VCC 2 IRRX 3 GND 4 IRTX 5 CIRRX Version 3.0
ページ18に含まれる内容の要旨
Tracer 2000 DVR user manual PCI bus pin assignment B62 B52 B49 SOLDER SIDE B1 A62 A52 A49 COMPONENT SIDE A1 Pin no. A B Pin no. A B 1 TRST* -12V 32 AD16 AD17 2 +12V TCK 33 VCC3 C/BE2* 3 NC GND 34 FRAME* GND 4 NC NC 35 GND IRDY* 5 +5V +5V 36 TRDY* VCC3 6 INTA* +5V 37 GND DEVSEL* 7 INTC* INTB* 38 STOP* GND 8 +5V INTD* 39 VCC3 LOCK* 9 NC PREN1* 40 SDONE PERR* 10 +5V NC 41 SBO* VCC3 11 NC
ページ19に含まれる内容の要旨
Tracer 2000 DVR user manual External Connector CRT Display Connector (VGA) 5 1 15 10 Pin no. Signal Pin no. Signal 1 RED 9 N/C 2 GREEN 10 GND 3 BLUE 11 N/C 4 N/C 12 N/C 5 GND 13 H-SYNC 6 GND 14 V-SYNC 7 GND 15 N/C 8 GND Audio Input connector: GPIO connector: USB connector: USB Ports Pin no. of Connector-B Pin Name Pin 2 USB0 + 6 3 USB0 - 14 4,8 GND 16 1,5 USB power 8 6 USB1 + 7 7 USB1 - 15 Version 3.0
ページ20に含まれる内容の要旨
Tracer 2000 DVR user manual COM 1 Connector 1 5 6 9 RS-232 Connector (COM1) Pin no. Signals 1 DCD 2 RX 3 TX 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI COM2 Connector 1 5 9 6 RS-232/RS-422/RS-485 Connector (COM2) (Please setup mode type by JP3) Pin no. RS-232 RS-422 RS-485 1 DCD TX- DATA- 2 RX TX+ DATA+ 3 TX RX+ 4 DTR RX- 5 GND GND GND 6 DSR RTS + 7 RTS RTS - 8 CTS CTS + 9 RI CTS - Version 3.0
