ページ1に含まれる内容の要旨
LMC11032A LMC11032AE
LMC11042A LMC11042AE
DFCS XGT+ Stand Alone Module
Converts 10GBASE-T Ethernet to SFP+ or XFP Fiber
Supports Pluggable 10 Gigabit Transceivers
- RJ45 to SFP+
- RJ45 to XFP
Customer Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
Support FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax
724-746-0746 • Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence,
Information
PA 15055-1018 • Web si
ページ2に含まれる内容の要旨
DFCS XGT+ Standalone Module NOM Statement FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interf erence to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifica
ページ3に含まれる内容の要旨
DFCS XGT+ Standalone Module lo descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a personal de servicio calificado. 9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o superficie similar puede bloquea la ventilación, no se debe c olocar en libreros o gabinetes que impidan el flujo de aire por los orificios de v en tilación. 10. E
ページ4に含まれる内容の要旨
DFCS XGT+ Standalone Module This User Manual describes the functions of the DFCS XGT+ Rev 1. Product Overview The DFCS XGT+ is a 10 Gigabit Ethernet media converter with one 10GBASE-T RJ-45 port and one pluggable transceiver port that provides copper-to-fiber and copper-to-copper media conversion. Copper-to-fiber conversion is achieved with XFP or SFP+ fiber transceivers. Copper-to-copper conversion is achieved with a CX4 XFP transceiver. The XGT+ supports high-power (power level 4) XFP tra
ページ5に含まれる内容の要旨
Installation Procedure SW2 - P2 LOOPBACK “P2-LB” When this DIP-switch is in the DOWN position (factory default), port P2 loopback is disabled. When this DIP-switch is in the UP “P2-LB” position, loopback is enabled on port P2. When enabled, all data received on port P2 is transmitted out port P2 and the connection between port P2 and port P1 is interrupted. NOTE: For the XFP model, simultaneous loopback of port P1 and port P2 requires the XFP transceiver to support lineside loopback capa
ページ6に含まれる内容の要旨
DFCS XGT+ Standalone Module SW3 and SW4 - RESERVED These DIP-switches are for factory use only and must always remain in the DOWN (factory default) position. 2) INSTALL STANDALONE MODULE AND CONNECT CABLES a. The XGT+ is available as a standalone module with built-in mounting brackets. For wall-mounting, attach the XGT+ to a wall, backboard or other flat surface. For tabletop installations, place the unit on a flat level surface. Attach the rubber feet to the bottom of the XGT+ to prevent
ページ7に含まれる内容の要旨
Installation Procedure 3) VERIFY OPERATION Once the module has been installed and configured per steps 1 and 2, verify the module is operational by viewing the LED indicators. Legend OFF State Color ON/Blinking State Pwr Off – No power. Green Green – Power On Green Green Solid – Fiber link (signal detect). Off – No Transceiver detected Amber Blinking (1Hz) – Port is disabled due to P1 Lk or no fiber link. Amber installed transceiver drawing more current than allowed. Green Solid – Transceive
ページ8に含まれる内容の要旨
Black Box Tech Support: FREE! Live. 24/7. Tech support the way it should be. Great tech support is just 30 seconds away at 724-746-5500 or blackbox.com. About Black Box Black Box Network Services is your source for an extensive range of networking and infrastructure products. You’ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support available in 30 seconds or less. © C
