ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-8157B
APPLICATIONS
LEXUS SC SERIES
1992-2000
99-8157B
KIT FEATURES
• ISO Mount Radio Provision With Pocket
• Painted Black To Match Factory Dash
KIT COMPONENTS
A) Radio Housing With Pocket • B) Housing Brackets • C) (4) #8 X 3/8” Phillips Screws
A B C
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2008 METRA ELECTRONICS CORPORATION
ページ2に含まれる内容の要旨
99-8157B TABLE OF CONTENTS Dash Disassembly - Lexus SC Series 1992-2000 . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Assembly - ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the mo
ページ3に含まれる内容の要旨
99-8157B DASH DISASSEMBLY LEXUS SC SERIES 1992-2000 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Push down on collar around base of shift knob then remove (2) Phillips screws then pull up on knob to remove. (Figure A) 3 Unclip and remove the shifter trim panel. Tip: Start at the front with ashtray open. (Figure B) 4 Open cup holder lid then unclip and remove the cup holder. Continued on page 2. B 1
ページ4に含まれる内容の要旨
99-8157B DASH DISASSEMBLY LEXUS SC SERIES 1992-2000 C 5 Remove (6) Phillips screws securing the upper console trim panel then unclip and remove the panel. (Figure C) 6 Remove (8) screws securing the radio and climate control assembly. 7 Remove (4) screws securing the climate controls to the bracket assembly and remove the climate controls. (Retain the screws and cli- mate controls for reuse during kit assembly) (Figure D) Continue to kit assembly. D 2
ページ5に含まれる内容の要旨
99-8157B KIT ASSEMBLY LEXUS GS SERIES 1992-2000 ISO MOUNT RADIO PROVISON WITH POCKET Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the Housing Brackets to the Radio Housing using the (4) #8 X3/8” Phillips screws. (Figure A) 2 Position the factory climate controls into the bracket/radio housing assembly and secure using the factory hardware. (Figure B) 3 Slide the aftermarket radio into the bracket/radio housing assembly and secure the radio to the assem
ページ6に含まれる内容の要旨
99-8157B FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disa
ページ7に含まれる内容の要旨
99-8157B NOTES 5
ページ8に含まれる内容の要旨
99-8157B INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 12/22/08 © COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST99-8157B
