ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-8227S
APPLICATIONS
TOYOTA 4 RUNNER
2010
99-8227S
KIT FEATURES
DIN Head unit provisions with pocket
ISO DIN Head unit provision with pocket
DDIN Head unit provision
ISO Stacked Head unit provision
Painted matte silver to match factory dash
KIT COMPONENTS
� A) Radio Housing � B) ISO Brackets � C) ISO Trim Plate � D) DDIN Brackets
� E) DDIN Trim Plate � F) Pocket � G) (4) PC-7503 Panel Clips � H) (2) Phillips Screws
AB
D E
C F
Wiring & Antenna Connectio
ページ2に含まれる内容の要旨
TABLE OF CONTENTS DASH DISASSEMBLY � TOYOTA 4 RUNNER 2010 . . . . . . . . . . . . . . . . 1-2 KIT PREPARATION � TOYOTA 4 RUNNER 2010 . . . . . . . . . . . . . . . . . 3 KIT ASSSEMBLY TOYOTA 4 RUNNER 2010 � DIN HEAD UNIT PROVISION . . . . . . . . . . . . . . . 4 � ISO DIN HEAD UNIT PROVISION . . . . . . . . . . . . 5 � DOUBLE DIN HEAD UNIT PROVISION . . . . . . . . . 6 CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessorie
ページ3に含まれる内容の要旨
99-8227S DASH DISASSEMBLY TOYOTA 4 RUNNER 2010 1 Unclip and remove the (2) climate A control knob trim panels. (Fig. A) 2 Unclip and remove the climate control. (Fig. B) 3 Remove (4) 10 MM bolts securing the radio. (Fig. C) B C Continued on Pg. 2 ............. 1
ページ4に含まれる内容の要旨
99-8227S DASH DISASSEMBLY TOYOTA 4 RUNNER 2010 4 Unclip and remove the vents from D the factory radio panel. (Fig. D) 5 Remove the (2) Phillips screws securing the trim panel on the top of the factory radio panel. (Fig. E) 6 Remove the (4) Phillips screws securing the outer a/c vent control wheel trim pieces. (Fig. F) E 7 Unclip and remove the hazard switch from the factory radio trim panel. (Fig. G) G F 2
ページ5に含まれる内容の要旨
99-8227S KIT PREPARATION TOYOTA 4 RUNNER 2010 1 Attach the outer a/c vent control A wheel trim pieces to the radio housing using the factory hardware. (Fig. A) 2 Attach the trim panel to the top of the radio housing using the factory hardware. (Fig. B) Note: 2 screws are provided “Justin” case. B 3 Attach the a/c vents to the radio housing. (Fig. C) 4 Snap the hazard switch into the radio housing. (Fig. D) 5 Attach (4) panel clips to the radio housing. (Fig. D) C D 3
ページ6に含まれる内容の要旨
99-8227S KIT ASSEMBLY TOYOTA 4 RUNNER 2010 DIN HEAD UNIT PROVISION 1 Locate the factory wiring harness in A the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Fig. A) B 3 Snap the pocket into the bottom opening of the radio housing. (Fig. B) 4 Slide the aftermarket head unit into
ページ7に含まれる内容の要旨
99-8227S KIT ASSEMBLY TOYOTA 4 RUNNER 2010 ISO DIN HEAD UNIT PROVISION 1 Locate the factory wiring harness in A the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Fig. A) B 3 Snap the pocket into the bottom opening of the radio housing. (Fig. B) 4 Slide the head unit into the radio opening u
ページ8に含まれる内容の要旨
99-8227S KIT ASSEMBLY TOYOTA 4 RUNNER 2010 DOUBLE DIN HEAD UNIT PROVISION 1 Locate the factory wiring harness in A the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Cut and remove the center bar from the radio housing. (Fig. A) 3 Snap the Double DIN brackets to the B inside edge of the Double DIN trim plate. (Fig. B) 4 Slide the Double DIN head unit or stacked ISO head u
ページ9に含まれる内容の要旨
NOTES
ページ10に含まれる内容の要旨
NOTES
ページ11に含まれる内容の要旨
NOTES
ページ12に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 99-8227S METRA. THE WORLD’S BEST KITS.™ 1-800-221-0932 metraonline.com © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION REV. 4/01/2010
