ページ1に含まれる内容の要旨
OPERATION MANUAL
BF-035
BOARD FAX
English
Français
Deutsch
Italiano
Español
PLUS
ページ2に含まれる内容の要旨
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation
ページ3に含まれる内容の要旨
OPERATION MANUAL BF-035 English PLUS
ページ4に含まれる内容の要旨
First of all, we would like to thank you very much for purchasing a PLUS Board Fax (Electronic Copyboard) CONFERENCE MODEL. Please read this Operation Manual before using the machine to get the best performance out of the product. We recommend that you keep this manual for future reference. EXPLANATION OF UL REGULATORY LABEL (USA ONLY) PLEASE NOTE: The description "Computer Rooms" on the label located on the rear of the copyboard, refers to areas where an abundance of computer control equipment
ページ5に含まれる内容の要旨
BF-035 BOARD FAX CARTON CONTENTS Please be sure all of the following items are included in the carton with the BF-035 BOARD FAX Copyboard main unit.......... 1 ACCESSORIES Set of Dry-eraseble markers (one each black, red and blue). Dry-Eraser (1) Fax Paper (30m(96ft) , 12mm(w/1/2") core) Operation Manual with warranty card OPTIONAL ACCESSORIES PC interface board - to enable integration of the BF-035 and your Personal Computer FEATURES The 1300mm(51")W × 920mm(36")H writing surf
ページ6に含まれる内容の要旨
PRODUCT FEATURES FRONT Writing panel 50mm(2") × 50mm (2") gridded surface area Tray Printer Operation panel T-shaped stand Printer hatch Caster REAR Expansion slot (for optional upgrades) T-shaped stand Optional accessory sold separately: PC interface board - to enable down- loading of board information from the BF-035 to the PC 2
ページ7に含まれる内容の要旨
CONTROL FUNCTIONS OPERATION PANEL Opening button .............................. Press this button to open the printer hatch when replacing the thermal paper. Power switch .................................. Press "I" to turn ON the power when starting machine operation. Power lamp ..................................... Press the switch, and the green lamp will blink on and off. The lamp will stay lit (green) when the read sensor inside the machine is ready for operatio
ページ8に含まれる内容の要旨
HOW TO USE BEFORE USE... Engage the caster locks to prevent board movement. Plug in and turn ON the power switch. POWER ON Turn on the power switch, and the panel will slide to show the first page. After PAPER OUT POWER blinking on and off 2-3 times, the power lamp remains lit. WHEN COPYING... Press the copy key. The panel slides once, and the written material will be copied on A4/Letter sized paper. However, when page 5 (projection screen) is shown, the panel will not move even if the
ページ9に含まれる内容の要旨
HOW TO USE WHEN SLIDING THE PANEL FORWARD... PAGE-L When page 1 is displayed, press the PAGE-L key, and the panel will move to page 2. The page number increases as many times as you press the key. The desired page (the page you wish to turn to) number will be indicated by the blinking LED. PAGE-R When page 4 is displayed, press the PAGE-R key, and the panel will move to page 3. The page number decreases as many times as you press the key. The page you wish to tarn to will be indicated by a fla
ページ10に含まれる内容の要旨
HOW TO USE As illustrated, set the new roll in so that the tip of thermal paper extends about 20cm (8") from the outlet. To close the cover, push both ends of it until it locks with a clicking noise. At this time, make sure that the thermal paper has not slipped off the edge. Cut off the extra thermal paper from the printer outlet. Replace the recording paper in the following situations When a red line appears at the edges of the recording paper. The red line will appear when there is only ab
ページ11に含まれる内容の要旨
MAINTENANCE/HOW TO STORE Carry out the following maintenance procedures periodically to ensure high quality printing performance at all times. (1) Cleaning of pages 1-4 When the surface gets stained, wipe it off with a slightly damp cloth. Also, if the stain is particularly stubborn, use a solution of water-thinned neutral detergent to clean. Do not start using the machine until the panel has completely dried. (2) Cleaning of projection screen (page 5) Wipe ordinary stains in the same manner as
ページ12に含まれる内容の要旨
HANDLING PRECAUTIONS 6. When replacing the thermal paper, do not place any objects on the open printer cover or apply weight to it. 7. After use, be sure to turn OFF the power switch. In addition, when it is not to be used for a long time, make certain that the plug is pulled form the outlet. 8. Always use the correct type of marker. Be careful not to use other markers as the panel may be damaged or, in some cases, the ink may be difficult to remove. 9. To ensure all information will be printed,
ページ13に含まれる内容の要旨
SPECIFICATIONS Item Specification Board surface size W1300 × H920 mm (51-3/16 × 36 inch) Effective reading size W1240 × H800 mm (48-7/8 × 34-3/4 inch) Number of pages 5 pages (4 pages can be copied) Screen The 5th page is a projection screen 1240 (50") × 880 (35") Panel driving method Bi-directional scrolling method Grid 50mm sq./2" sq. Writing instruments Special dry erase markers (black/blue/red) Reading method CCD sensor plane scanning Recording method Thermal printing with thermal head Recor
ページ14に含まれる内容の要旨
14-4146-01A
