ページ1に含まれる内容の要旨
Table of Contents
Characteristic Functions 1
Important Safety Instructions 2
Technical Specifications 5
The Technical Specifications for Final Product 5
Technical Specifications for TV 6
VGA Display Mode 6
Power Management 6
Packing Listing 6
Installation & Connection 7
Antenna Connection 7
Power Connection 8
Computer Connection 8
HDMI digital port Connection 8
AV1 Video Signal Connection 9
ページ2に含まれる内容の要旨
Characteristic Functions 1. LCD panel with no glint and low radiation can ease eyes' fatigue and protect eyes. 2. High-quality LCD panel is adopted with high brightness, high contrast, wide viewing angle, and super fast response time. Super fast response time can greatly eliminate the shadow of moving images. 3. TV/Monitor with two in one and multiple input ports can easily switch among the Modes. 4. De-interlacing image disposal is adopted. Today's most advanced techni
ページ3に含まれる内容の要旨
Important Safety Instructions Thank you to choose the LCD TV made by our company, a valuable product with excellent quality and multiple functions. This machine will bring you more audiovisual enjoyment. Its design can insure user s safety. All machine are strictly tested before leaving factory. But incorrect use can lead to electric shock or fire. In order to insure safety and extend its life, please read below regulations carefully before using it and comply with the following saf
ページ4に含まれる内容の要旨
Important Safety Instructions cellar and similar environment. During a thunder rain weather, do not touch the power cord and antenna cable. Please pull out the power line and aerial plugs for preventing thunder and lightning damage to this machine. All cables can be connected or pull out only after power supply is turned off. The power cord must be taken off before you clean the machine. Do not use the liquid cleanser or aerosol cleanser. It is
ページ5に含まれる内容の要旨
Important Safety Instructions When the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. The machine should not suffer from waterdrop or watersplash, do not place the vessel with water (or other liquids) on it, for like this it is possibly to cause fire or electric shock. The attaching plug should be inserted into the power point completely, otherwise it may cause spark to bring
ページ6に含まれる内容の要旨
Technical Specifications The Technical Specifications for Final Product Panel size 26 32 Max. Resolution 1366 768 1366 768 Best Resolution 1360 768@60Hz 1360 768@60Hz Pixel Pitch 0.4215mm 0.4215mm 0.51075mm 0.51075mm Active Area 575.770mm 323.710mm 697.6845mm 392.256mm Color 16.7M 16.7M Panel Surface Disposal Anti Glare Anti Glare Power Supply 100V-240VAC 60/50Hz 100V-240VAC 60/50Hz Power Consumption of Speaker 10W+10W 10W+10W 0 0 Control Area of Remote Control 8M 30 8M 30 Operating Environm
ページ7に含まれる内容の要旨
Technical Specifications Technical Specifications for TV 1.Supported Systems PAL+SECAM or PAL+NTSC 2.Storage channels: 199 3.TV(RF): 75 Imbalance 4.AV Video-Input: 75 ,1VP-P, RCA 5.AV Audio-Input: 20K , 500mV RMS 6.YPbPr/HDMI Video Input: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p VGA Display Mode No. Mode Resolution Refresh 720X400 70Hz 1 VGA 640X480 60Hz 2 SVGA 800X600 60Hz 3 XGA 1024X768 60Hz 4 WXGA 1360X768 60Hz Note: Recommended mode:1360X768@60Hz Power Management This product is
ページ8に含まれる内容の要旨
Installation & Connection Antenna Connection It is better to use outdoor antenna or CATV cable if you want to watch the colorful and hi-definition pictures. Attention: Please turn off TV power before the outdoor antenna is connected to the TV signal input port. Outdoor antenna can't be located near the high voltage cables. Please pull out the plug of outdoor antenna to avoid thunder shock in thunder weather. 7
ページ9に含まれる内容の要旨
Installation & Connection Power Connection Notes: 1.This machine uses AC 100-240V, 60/50Hz. 2.If a long time at leisure, please disconnect it from power supply. Computer Connection Please connect one end of VGA cord with the output port of the computer (available for both desktop or laptop computer), and another end of VGA cord with the input port of the VGA on its rear cover. HDMI digital port Connection Connect external HDMI high signal source to HDMI digital input port of this mac
ページ10に含まれる内容の要旨
Installation & Connection AV1 Video Signal Connection Through composite cable, connect AV equipment VIDEO output termination to this machine VIDEO input, and AV equipment AUDIO output termination to this machine AUDIO input, respectively. WW W W YY RR R R Y Yellow (VIDEO) W White (AUDIO-L) R Red (AUDIO-R) CVBS, DVD Player or other machine with CVBS/S-Video. 9
ページ11に含まれる内容の要旨
Installation & Connection AV2 Video Signal Connection For easy connection to AV Video Signal, there are a group of AV Video Signal input ports on the down part on the left side of the machine. The connection method is the same as AV1. Y Yellow (VIDEO) W White (AUDIO-L) R Red (AUDIO-R) S-VIDEO-2 AUDIO-R R R W W AUDIO-L Y Y VIDEO-2 CVBS, DVD Player or other machine with CVBS/S-Video. Earphone Socket: The TV speakers will be shut off when earphone is inserted into this socket. 10
ページ12に含まれる内容の要旨
Installation & Connection YPbPr/YCbCr Input Connection If the signal source is DVD, Digital wired receiver or equipments with the YPbPr/YCbCr output, recommends you to connect YPbPr or YCbCr output with the TV YPbPr/YCbCr input. In order to obtains the better picture quality, at the same time, please connect its audio output with TV audio input as shown in the following chart. If you choose the YPbPr/YCbCr signal, please set signal source selection under YPbPr pattern. AV machine CVBS, DVD
ページ13に含まれる内容の要旨
Position of Control Keys Front Panel Control Keys SOURCE 3 CH+ 5 CH- VOL+ 6 VOL- MENU 4 7 1 2 1) Power Indicator 2) Remote Receiving Sensor 3) SOURCE: Press this key to enter the menu of signal source and choose signal source. 4) MENU: Press this key to enter main menu 5) CH+/CH-: Press these two keys to select the channel, and adjust the options you need under OSD operation. 6) VOL+/VOL-: Press these two keys to add or reduce volume, and adjust the analog value under OSD oper
ページ14に含まれる内容の要旨
Remote Control POWER MUTE Power Mute Numerical key F1 Program list Freeze picture SMART S SMART P Smart sound Smart image OK OK Cursor Key Menu MENU Channel Volume VOL CH SOURCE Source INFO 1 6 :9 Info Zoom Return Time COLOR P/N A U D IO Color Color system Telecontrol battery installation method Take off the cover of battery box, fix two AAA batteries with 1.5 volt, and conform with the polarity of remote control battery box. Note: Appearance of the remote control may be different from thi
ページ15に含まれる内容の要旨
Remote Control Remote Control Key Instruction Key Function POWER Turn on or standby MUTE Eliminate sound Numerical key Number input button F1 Freeze picture Program list Look through or edit Program list MENU Press this button to display menu SMART S Intelligent sound mode selection: STANDARD, NEWS, MUSIC, PERSONAL SMART P Intelligent image mode selection: STANDARD, DYNAMIC, SOFT, PERSONAL SOURCE Press this button to display signal source selection menu Cursor key Up or Down cursor button: func
ページ16に含まれる内容の要旨
Basic Operation Instruction Power On Plug power cord into the electrical socket and press '' '' key on the front panel, then press ''Power'' key on the remote control to turn on the TV. Standby Press ''Power''key on the remote control. TV will be in standby. Special Attention: 1.TV set will automatically turn to standby if there is no signal input for 5 minutes when TV turns on. 2.TV set will automatically turn to standby when the preset time of turning off reaches
ページ17に含まれる内容の要旨
Basic Operation Instruction Press ''Source''key to display the signal source menu or exit signal source menu. 6. During the operation, the selections which can not be adjusted at current mode will be hidden automatically and the color of the selections will be changed into gray. 7. Menu Operation Instruction in this manual is explained according to TV mode. The operations in other modes are similar to the one in TV mode. Users can take it as reference. PICTURE Select t
ページ18に含まれる内容の要旨
Basic Operation Instruction SOUND Select to enter the SOUND submenu. Press " Up/Down " key on the remote control or the key "CH+/CH-" on the front SOUND panel to choose what you need. Press the BASS 50 "Left / Right" key on the remote control or TREBLE 50 BALANCE 50 the "VOL+/VOL-" key on the front panel to SOUND MODE STANDARD adjust analog value or state (see below table). SEL ADJ MENU EXIT Special Attention 1. Normally, 50 value of adjustment is recommended; 2.
ページ19に含まれる内容の要旨
Basic Operation Instruction OSD Select to enter the OSD submenu. Press "Up/Down" key on the remote control or "CH+/CH-" key on the front panel to choose OSD what you need. Press the "Left/Right" key on OSD - H POSITION 50 OSD - V POSITION 50 OSD - DURATION 15 the remote control or the "VOL+/VOL-" key OSD - HALFTONE 100 OSD - LANGUAGE ENGLISH on the front panel to adjust analog value or state (see below table). SEL ADJ MENU EXIT Option Function
ページ20に含まれる内容の要旨
Basic Operation Instruction TV Select to enter the TV submenu. Press "Up/Down" key on the remote control or "CH+/CH-" key on the front panel to choose TV what you need. Press the "Left/Right"key on COLOR SYSTEM AUTO SOUND SYSTEM M the remote control or the "VOL+/VOL-" key MTS MONO SKIP OFF on the front panel to adjust analog value or AUTO SCAN MANUAL SEARCH state (see below table). FINE TUNING CHANNEL EDIT SEL ADJ MENU EXIT Option Function
