ページ1に含まれる内容の要旨
Internal Use Only
North/Latin America http://aic.lgservice.com
Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com
LED LCD TV
SERVICE MANUAL
CHASSIS : LD22E
MODEL: 42LS570S/570T/575S/575T
MODEL: 42LS570S/570T-ZB 42LS575S/575T-ZD
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
P/NO : MFL67360908 (1202-REV00) Printed in Korea
ページ2に含まれる内容の要旨
CONTENTS CONTENTS .............................................................................................. 2 SAFETY PRECAUTIONS ........................................................................ 3 SERVICING PRECAUTIONS .................................................................... 4 SPECIFICATION ....................................................................................... 6 ADJUSTMENT INSTRUCTION .............................................................. 10 SCR
ページ3に含まれる内容の要旨
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer. General Guidance Leakage Current Hot Check
ページ4に含まれる内容の要旨
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service 2. After removing an electrical assembly equipped with ES manual and its supplements and addenda, read and follow the devices, place the assembly on a conductive surface such as SAFETY PRECAUTIONS on page 3 of this publication. aluminum foil, to prevent electrostatic charge buildup or expo- NOTE: If unforeseen circumstances create conflict between the sure of the assembly. following servicing precautions and any
ページ5に含まれる内容の要旨
IC Remove/Replacement 3. Solder the connections. Some chassis circuit boards have slotted holes (oblong) through CAUTION: Maintain original spacing between the replaced which the IC leads are inserted and then bent flat against the cir- component and adjacent components and the circuit board to cuit foil. When holes are the slotted type, the following technique prevent excessive component temperatures. should be used to remove and replace the IC. When working with boards using the familiar r
ページ6に含まれる内容の要旨
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range 3. Test method This specification is applied to the LCD TV used LD22E 1) Performance: LGE TV test method followed chassis. 2) Demanded other specification - Safety : CE, IEC specification - EMC : CE, IEC 2. Requirement for Test - Wireless : Wireless HD Specification (Option) Each part is tested as below without special appointment. 1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F
ページ7に含まれる内容の要旨
No. Item Specification Remarks 1) PAL-BG DVB-S: Satellite 2) PAL-DK 3) PAL-I/I’ 4) SECAM L/L’, DK, BG, I 2 Broadcasting system 5) DVB-T 6) DVB-C 7) DVB-T2 8) DVB-S ► DVB-T - Guard Interval(Bitrate_Mbit/s) 1/4, 1/8, 1/16, 1/32 - Modulation : Code Rate QPSK : 1/2, 2/3, 3/4, 5/6, 7/8 16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 ► DVB-T2 - Guard Interval(Bitrate_Mbit/s) 1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256, - Modulation : Code Rate QPSK : 1/2, 2/5, 2/3, 3/4
ページ8に含まれる内容の要旨
5. Component Video Input (Y, Cb/Pb, Cr/Pr) No. Resolution H-freq(kHz) V-freq(Hz) Porposed 1 720×480 15.73 60.00 SDTV, DVD 480i 2 720×480 15.63 59.94 SDTV, DVD 480i 3 720×480 31.47 59.94 480p 4 720×480 31.50 60.00 480p 5 720×576 15.625 50.00 SDTV, DVD 625 Line 6 720×576 31.25 50.00 HDTV 576p 7 1280×720 45.00 50.00 HDTV 720p 8 1280×720 44.96 59.94 HDTV 720p 9 1280×720 45.00 60.00 HDTV 720p 10 1920×1080 31.25 50.00 HDTV 1080i 11 1920×1080 33.75 60.00 HDTV 1080i 12 1920×1080 33.72 59.94 HDTV 1080i 1
ページ9に含まれる内容の要旨
7. HDMI Input 7.1. DTV mode No. Resolution H-freq(kHz) V-freq.(kHz) Proposed 1. 640*480 31.469 / 31.5 59.94/60 SDTV 480P 2. 720*480 31.469 / 31.5 59.94 / 60 SDTV 480P 3. 720*576 31.25 50 SDTV 576P 4. 720*576 15.625 50 SDTV 576I 5. 1280*720 37.500 50 HDTV 720P 6. 1280*720 44.96 / 45 59.94 / 60 HDTV 720P 7. 1920*1080 33.72 / 33.75 59.94 / 60 HDTV 1080I 8. 1920*1080 28.125 50.00 HDTV 1080I 9. 1920*1080 26.97 / 27 23.97 / 24 HDTV 1080P 10. 1920*1080 25 HDTV 1080P 11. 1920*1080 33.716 / 33.75 29.976
ページ10に含まれる内容の要旨
ADJUSTMENT INSTRUCTION 3.1.3. Adjustment 1. Application Range (1) Adjustment method This specification sheet is applied to all of the LED LCD TV ▪ Don’t need to adjust ADC because there is data in OTP with LD22E chassis. and adjusted initially. ▪ Check ADC adjustment 1) Press In start key on the Adj. Remote Control, then 2. Designation Adjust ADC(OTP) status is displayed on “1.Adjustment (1) B ecause this is not a hot chassis, it is not necessary to check”. Select “2.ADC Data”, then ADC d
ページ11に含まれる内容の要旨
3.3.3. WIDEVINE key Inspection 3.2. MAC address D/L, CI+ key D/L, Widevine - Confirm key input data at the "IN START" MENU Mode. key D/L, ESN D/L Connect: USB port Communication Prot connection ▪ Com 1,2,3,4 and 115200(Baudrate) Mode check: Online Only ▪ check the test process: DETECT -> MAC -> CI -> Widevine -> ESN ▪. Play: START ▪. Result: Ready, Test, OK or NG ▪. Printer Out (MAC Address Label) 3.4. LAN PORT INSPECTION(PING TEST) Connect SET → LAN port == PC → LAN Port SET PC 3.4.1. Equip
ページ12に含まれる内容の要旨
2) Check the key download for transmitted command 3.5. Model name & Serial number Download (RS232: ci 00 10) 3.5.1. Model name & Serial number D/L CMD 1 CMD 2 Data 0 ▪ Press "Power on" key of service remote control. (Baud rate : 115200 bps) C I 1 0 ▪ Connect RS232 Signal Cable to RS-232 Jack. ▪ Write Serial number by use RS-232. 3) Result value ▪ Must check the serial number at Instart menu. - Normally status for download : OKx - Abnormally status for download : NGx 3.5.2. Method & notice (1
ページ13に含まれる内容の要旨
▪ Reference 4. Manual Adjustment - HDMI1 ~ HDMI4 / RGB * ADC adjustment is not needed because of OTP(Auto ADC - In the data of EDID, bellows may be different by S/W or adjustment) Input mode. ⓐ. Product ID 4.1 E DID(The Extended Display Identification HEX EDID Table DDC Function Data)/DDC(Display Data Channel) download 0001 01 00 Analog/Digital 4.1.1. Overview ⓑ. Serial No: Controlled on production line. It is a VESA regulation. A PC or a MNT will display an optimal ⓒ. Month, Year: Contr
ページ14に含まれる内容の要旨
Ex) wb 00 00 -> Begin white balance auto-adj. 4.2. White Balance Adjustment wb 00 10 -> Gain adj. 4.2.1. Overview ja 00 ff -> Adj. data ▪ W/B adj. Objective & How-it-works jb 00 c0 (1) Objective: To reduce each Panel's W/B deviation ... (2) How-it-works : When R/G/B gain in the OSD is at 192, it ... means the panel is at its Full Dynamic Range. In order to wb 00 1f → Gain adj. completed prevent saturation of Full Dynamic range and data, one *(wb 00 20(Start), wb 00 2f(en
ページ15に含まれる内容の要旨
▪ Adjustment condition and cautionary items 4.3. EYE-Q function check 1) Lighting condition in surrounding area (1) Turn on TV. Surrounding lighting should be lower 10 lux. Try to (2) Press EYE key of Adjustment remote control. isolate adj. area into dark surrounding. (3) Cover the Eye Q II sensor on the front of the using your 2) Probe location hand and wait for 6 seconds. : Color Analyzer(CA-210) probe should be within 10 cm (4) Confirm that R/G/B value is lower than 10 of the "Raw and
ページ16に含まれる内容の要旨
4.7. Wi-Fi Test 4.8. LNB voltage and 22KHz tone check Step 1) Turn on TV (only for DVB-S/S2 model) Step 2) Select Network Connection option in Network Menu. ▪ Test method (1) Set TV in Adj. mode using POWER ON. (2) Connect cable between satellite ANT and test JIG. (3) Press Yellow key(ETC+SWAP) in Adj Remote control to make LNB on. (4) Check LED light ‘ON’ at 18 V menu. (5) Check LED light ‘ON’ at 22 KHz tone menu. (6) Press Blue key(ETC+PIP INPUT) in Adj Remote control to make LNB off. (7)
ページ17に含まれる内容の要旨
4.12. GND and Internal Pressure check 6. USB S/W Download(Service only) (1) Put the USB Stick to the USB socket. 4.12.1. Method (1) GND & Internal Pressure auto-check preparation (2) Automatically detecting update file in USB Stick. - Check that Power cord is fully inserted to the SET . - If your downloaded program version in USB Stick is Low, (If loose, re-insert) it didn't work. But your downloaded version is High, USB data is automatically detecting. (2) Perform GND & Internal Pressure a
ページ18に含まれる内容の要旨
SCREW ASSEMBLY WORKING GUIDE ■ Screw specification and application situation AAA AAA AAA AAA AAA AAA BBB BBB AAA AAA AAA AAA BBB BBB AAA AAA C C C C C C C C C C C C C C C C C C C C C C C C DDD DDD DDD DDD Check Screw Type When Screw is assembled at 'A' Part. If 'C' Screw is used at the 'A' part, Module will get damaged. Copyright ©
ページ19に含まれる内容の要旨
BLOCK DIAGRAM Copyright © LG Electronics. Inc. All rights reserved. LGE Internal Use Only - 19 - Only for training and service purposes SYSTEM SYSTEM DDR3 X DDR3 X X_TAL 1600 X 1600 X 27MHz ANALOG Air/ 16 16 SYSTEM DEMOD Cable (2Gb) (2Gb) DDR3 X TUNER (T/C) 1600 X 16 P_TS DIGITAL P_TS (2Gb) DEMOD (T/C) IF(+/-) DDR T/C Demod SYSTEM CONTROLER A/B CVBS DDR3 X CVBS DIGITAL DVB-S TUNER 1600 X 16 DEMOD P_TS (S2) (S2) TS_S/P (2Gb) USB1 USB2 SYSTEM EEPROM X 1 USB USB3 (256Kb)
ページ20に含まれる内容の要旨
EXPLODED VIEW IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer. Copyright © LG Electronics. In