ページ1に含まれる内容の要旨
52" LCD Display Monitor
USER’S MANUAL
BEDIENERHANDBUCH
MANUAL DEL USUARIO
MANUEL UTILISATEUR
MANUALE UTENTE
GEBRUIKERSHANDLEIDING
ページ2に含まれる内容の要旨
Index Important Information ................................................................................................................................... English-2 Safety Precautions, Maintenance & Recommended Use ........................................................................... English-4 Contents ....................................................................................................................................................... English-5 Parts Name and Functio
ページ3に含まれる内容の要旨
Important Information DECLARATION OF CONFORMITY This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: Mitsubishi Digital Electronics America, Inc. Address: 9351 Jeronimo Road, Irvine, California 92618 U.S.A. Tel. No.: +1 - (949) 465-6000
ページ4に含まれる内容の要旨
Important Information WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE TH
ページ5に含まれる内容の要旨
Safety Precautions, Maintenance & Recommended Use FOR OPTIMUM PERFORMANCE, PLEASE NOTE • The power cable connector is the primary means of THE FOLLOWING WHEN SETTING UP AND USING detaching the system from the power supply. The monitor THE LCD COLOR MONITOR: should be installed close to a power outlet, which is easily accessible. • DO NOT REMOVE MONITOR BACK COVER. There are • Handle with care when transporting. Save packaging for no user serviceable parts inside and opening or removing
ページ6に含まれる内容の要旨
Contents Your new MDT521S monitor box* should contain the following: • LCD monitor • Screw for Clamper (To prevent from falling) x 2 • Power Cord (3 m) • CAT5 Tx BOX • Video Signal Cable (4 m) • CD-ROM • User’s Manual • Wireless Remote Control and AAA Batteries • Clamper x 2 (To prevent from falling) • Clamper x 3 (For securing cables) • Clamper x 2 (For securing the power cord and HDMI cable) 52" LCD Display Monitor USER’S MANUAL BEDIENERHANDBUCH MANUAL DEL USUARIO MANUEL UTILISATEUR MANUA
ページ7に含まれる内容の要旨
Parts Name and Functions Buttons, Switch, and Indicator ON OFF Remote control sensor and Power indicator UP ( ) button Receives the signal from the remote control (when using the Activates the OSD menu when the OSD menu is turned-off. wireless remote control). See also page 9. Acts as button to move the highlighted area up to select Glows green when the LCD monitor is in active and glows the adjustment with OSD menu. red when the LCD is in POWER OFF mode. When the LCD is DOWN ( ) button
ページ8に含まれる内容の要旨
Connectors and Terminals (OUT) (IN) (OUT) (IN) (OUT) (IN) (IN) (IN) CAT5 input/output connectors (modular con- EXTERNAL SPEAKER TERMINAL To output the audio signal for external speakers from AUDIO 1, nector 8 pin) 2, 3 jack or HDMI. The IN (RGB5 IN) connector is for connecting the CAT5 Tx BOX or the CAT5 OUT connector of a multi-connected AUDIO OUT MDT521S. To output the audio signal from the AUDIO IN 1, 2, 3 jack or The OUT connector is for connecting the CAT5 (RGB5) IN HDMI. connector
ページ9に含まれる内容の要旨
Wireless Remote Control AUDIO INPUT button Press to change the audio source for each video source. The audio source is changed from [AUDIO1] to [AUDIO2], [AUDIO3] and [HDMI] in order. Note that you cannot select the audio source for [VIDEO] or [VIDEO]. [HDMI] is selectable only when the video source is [RGB 1] and [RGB 2]. PIP (Picture In Picture) button ON/OFF button: PIP-ON/OFF. See page 27. INPUT button: Select the “picture in picture” input signal. CHANGE button: Replaces to the m
ページ10に含まれる内容の要旨
CAT5 Tx BOX < Operating Range for the Remote Control > Point the top of the remote control toward the LCD monitor's remote sensor during button operation. Use the remote control within a distance of about 7 m/23 ft. from the front of the LCD monitor's remote control sensor and at a horizontal and vertical angle of within 30° within a USB (B type) distance of about 3 m/10 ft. Connected to the USB connector (A type) of the computer. CAUTION: We have checked the operation of the USB connecto
ページ11に含まれる内容の要旨
Setup Procedure • Place “AAA” batteries matching the + and - signs on each 1. Determine the installation location battery to the + and - signs of the battery compartment. CAUTION: • Do not mix battery types. DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY • Do not combine new batteries with used ones. It causes YOURSELF. shorter battery life or leakage of batteries. Installing your LCD display must be done by a qualifi ed tech- • Remove dead batteries immediately to prevent battery nician. Cont
ページ12に含まれる内容の要旨
How to install the stands 6. Operate the attached external equipment 1. Please turn monitor off. Display the signal on the external equipment you wish. 2. Fasten screws on both sides of the monitor. NOTE: 7. Adjust the sound Install the stands so that their longer portions come to the Make adjustments lowering or rising the volume as required. front. How to remove the stands 8. Adjust the screen (See pages 24-34) 1. Spread the protective sheet on the fl at surface, such as a Make adjustments
ページ13に含まれる内容の要旨
MDT521S 13. When MDT521S is installed in portrait CAT5 video connection position The CAT5 video connection function is for transmitting the Conditions analog RGB video signal of the computer and the control MDT521S can be installed in portrait position, under the fol- signal of the monitor over a long distance using CAT5 cables. lowing conditions: The computer can control the monitor via the supplied CAT5 Caution: Tx BOX. Portrait position is effective only when wall-mounted or Caution: c
ページ14に含まれる内容の要旨
2. Connect the D-SUB input connector of the CAT5 Tx BOX 2) CAT5 EQ and the VGA (D-SUB) output connector of the computer Make adjustment so that blur and smear of the displayed let- using the signal cable (mini D-SUB 15-pin cable) supplied ters and graphic objects are minimized. with the monitor. 3) CAT5 R-GAIN/G-GAIN/B-GAIN 3. Connect the modular connector of the CAT5 Tx BOX and When the displayed image is dark, increase each value. the CAT5 (RGB5) IN connector of the monitor using a When w
ページ15に含まれる内容の要旨
How to Mount and Attach Options to the LCD Monitor You can attach mounting accessories to the LCD monitor in 3. Ventilation Requirements for enclosure one of the following two ways: mounting 1. In the upright position To allow heat to disperse, leave space between surrounding objects as shown in the diagram below. 2. Lay the screen face down Lay the protective sheet on a table, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the scre
ページ16に含まれる内容の要旨
Connections Before making connections: * First turn off the power of all the attached equipment and make connections. * Refer to the user manual included with each separate piece of equipment. Wiring Diagram Monitor LCD monitor (second monitor) Personal Personal DVD player Stereo amplifier computer computer (HDMI) (analog RGB) (DVI-D) VCR (RCA) External speaker English-15 English
ページ17に含まれる内容の要旨
Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer's screen image. Some video cards may not display an image correctly. Connect the LCD Monitor to a Personal Computer • To connect the RGB 3 IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal cable (mini D-sub 15 pin to mini D-sub 15 pin). Select RGB 3 from the INPUT button on the LCD monitor or D-SUB button on the remote control. • To conn
ページ18に含まれる内容の要旨
Connecting with Digital Interface Equipment Connections can be made with equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard. Connect the LCD Monitor to a Computer with a Digital Output • To connect the RGB 2 IN connector (DVI-D) on the LCD monitor, use a DVI-D cable. Select RGB 2 from the INPUT button on the LCD monitor or DVI-D button on the remote control. Select the “DVI INPUT MODE” to “DVI-PC“. (See page 31) • To connect the RG
ページ19に含まれる内容の要旨
Connecting a DVD Player with component out / HDMI out / DVI out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Refer to your DVD player owner’s manual for more information. Connect the LCD Monitor to a DVD Player • To connect the DVD/HD IN connector (BNC) on the LCD monitor, use a separately available BNC connector cable. You will need a BNC-to-RCA adapter to connect a DVD player with an RCA pin jack to the BNC connector cable (not provided). Select DVD-
ページ20に含まれる内容の要旨
Connecting to a VCR / Stereo Amplifi er You can connect your VCR / stereo amplifi er to your LCD monitor. Refer to your VCR / stereo amplifi er owner's manual for more information. Connect the LCD Monitor to a VCR / Stereo Amplifi er • To connect the VIDEO IN connector (RCA, BNC or S-VIDEO) on the LCD monitor, use a video cable or S-video cable. Use a separately available RCA cable or S-video cable. To connect the AUDIO IN connector (RCA) on the LCD monitor, use an RCA cable. When connect the R
