ページ1に含まれる内容の要旨
REAR CAMERA
MODEL
INSTALLATION MANUAL
Be sure to read this installation manual thoroughly prior to installation and making connections. If installation
methods or non-standard parts not specified in this installation manual are used, accidents or injury may
result.
Professional techniques and experience are required in order to install this system. It is recommended that
you contact the place of purchase for installation to be carried out. After reading the installation manual
thoroughly, keep t
ページ2に含まれる内容の要旨
Components Check that all of the following components are present Check that all of the following components are present Components Rear Camera Components Rear camera Bracket Screw Double-sided tape 1 2 3 4 x 1 x 1 (M3x6)x 2 (Spare) x 1 5 Cable rail 6 Harness affixing tape 7 Waterproof cushion x 6 x 2 x 1 *The rear camera cable includes a 3-pin intermediate connector (male-female) to improve ease of installation. For your safety in using the BEC105 For your safety in using the BEC105 Warnings
ページ3に含まれる内容の要旨
• • This unit is intended for operation in DC 12volt, • • Bundle cables and harnesses with electrical tape negative-grounded vehicles only. Never use it in or wire ties to prevent them from interfering with 24- volt vehicles such as heavy trucks or diesel moving parts. If they should entangle with the vehicles with cold-region specifications. steering wheel, shift lever or brake pedal, an accident may result. • • Do not install this product in locations where it may interfere with the oper
ページ4に含まれる内容の要旨
Points to note after installing the rear camera Points to note after installing the rear camera - Method of use - • • Do not place too much reliance on the back-eye camera. • • The backeye camera is meant to be used as a supplementary aid to help in avoiding obstructions. • • If the lens is obscured by raindrops or similar, it may reduce in the effectiveness of the camera. • • The position of the images displayed on the screen will vary depending on the vehicle conditions (such as number
ページ5に含まれる内容の要旨
Installation Diag Installation Diagr ram am 1 Rear camera Rear camera cable
ページ6に含まれる内容の要旨
Installing the Rear camera Installing the Rear camera Notes on installation The cables should be secured with tape or a similar securing method to prevent any obstructions while driving. If • they get wound around components such as the steering wheel, shifting lever or brake pedal, accidents may result. • Install the rear camera bracket so that the entire mounting side surface can be affixed securely to the vehicle. If the contact surface area is insufficient, the camera may fall off while d
ページ7に含まれる内容の要旨
Decide on the installation position for the rear camera. - If installing underneath a rear spoiler (example) - Tip Note the following when deciding on the 1 Rear camera installation position for the rear camera. • Provisionally attach the rear camera with tape and adjust its angle (see page 11) in a position to view the rear of the vehicle. Front of vehicle When the double-sided tape has been used once, the adhesive will be reduced if it is used again. • Install the rear camera in a positio
ページ8に含まれる内容の要旨
- If installing underneath a rear spoiler (example) - Wipe the installation surface free of any dirt, water or 2 grease. Peel off the backing paper from the double-sided 3 tape on the bracket, and affix the bracket to a flat part of the rear spoiler. Front of vehicle 2 Bracket Tip • After affixing the bracket, push the bracket firmly on the mounted surface ensure that it is securely attached. • The adhesive strength of the double-sided tape will be reduced at low temperatures (20°C) or less.
ページ9に含まれる内容の要旨
– If installing underneath a rear spoiler (example) – Wipe the installation surface free of any dirt, water or 6 grease. Peel off the backing paper from the double-sided 7 tape on the bracket, and affix the bracket to a flat part of the back door. Tip Front of 2 Bracket vehicle • After affixing the bracket, push the bracket firmly on the mounted surface ensure that it is securely attached. • The adhesive strength of the double-sided tape will be reduced at low temperatures (20˚C) or less. Use
ページ10に含まれる内容の要旨
Route the rear camera cable while securing it Clamp 10 with the cable rails, commercially-available cable tie,and commercially-available clamp. Tip Cable tie The cable rails should be cut to appropriate Front of vehicle • lengths. Clamp • Confirm that the rear camera cable does Front of vehicle not get pulled and that the cable ties and clamps do not come off when the back door is opened and closed. • Take care when routing the cable through the trunk to ensure that rainwater cannot get insi
ページ11に含まれる内容の要旨
Camer Camera Angle Adjustment a Angle Adjustment • When adjusting the camera images, apply the vehicle's parking brake and be sure to chock the wheels of the vehicle so that the vehicle will not move, otherwise accidents or injuries may occur. After connecting the rear camera cable to the 1 main unit, connect the battery cable. - Main unit - Move the selector lever to the R position to 2 display images from behind the vehicle. Loosen the adjustment screw and adjust the 3 angle of the camera so
ページ12に含まれる内容の要旨
System connection e System connection example xample Never cut the insulation on the power cable or use it to power any other equipment. If the rated current capacity • of the power cable is exceeded, fire and electric shocks may result. • The cables should be bound together with tape or with a similar technique so that they do not interfere with driving. If they become wound around parts such as the steering wheel, shifting lever or brake pedal, accidents may result. MAIN UNIT (sold separate
