ページ1に含まれる内容の要旨
BDL5571V
www.philips.com/welcome
User Manual (English)
ページ2に含まれる内容の要旨
User Manual BDL5571V SAFETY INSTRUCTIONS WARNINGS AND PRECAUTIONS KNOW THESE SAFETY SYMBOLS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been i
ページ3に含まれる内容の要旨
User Manual BDL5571V Read and follow these instructions when connecting and using your computer monitor: Unplug the monitor if you are not going to use it for an extensive period of time. Unplug the monitor if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids. Consult a service technician if the monitor does not operate normally when you have followed th
ページ4に含まれる内容の要旨
User Manual BDL5571V REGULATORY INFORMATION CE DECLARATION OF CONFORMITY MMD declare under our responsibility that the product is in conformity with the following standards • EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment) • EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment) • EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment) • EN61000-3-2:2006 (Limits for Harmonic Current Emis
ページ5に含まれる内容の要旨
User Manual BDL5571V POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To compl
ページ6に含まれる内容の要旨
User Manual BDL5571V INFORMATION FOR UK ONLY WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place
ページ7に含まれる内容の要旨
User Manual BDL5571V NORTH EUROPE (NORDIC COUNTRIES) INFORMATION Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE
ページ8に含まれる内容の要旨
User Manual BDL5571V TABLE OF CONTENTS 1. UNPACKING AND INSTALLATION ................................................................................................................... 9 1.1. UNPACKING .......................................................................................................................................... 9 1.2. PACKAGE CONTENTS ......................................................................................................................... 9 1.3.
ページ9に含まれる内容の要旨
User Manual BDL5571V 6.1. PIXELS AND SUB-PIXELS .................................................................................................................. 51 6.2. TYPES OF PIXEL DEFECTS + DOT DEFINITION ............................................................................. 51 6.3. BRIGHT DOT DEFECTS ..................................................................................................................... 52 6.4. DARK DOT DEFECTS .....................................
ページ10に含まれる内容の要旨
User Manual BDL5571V 1. UNPACKING AND INSTALLATION 1.1. UNPACKING This product is packed in a carton, together with the standard accessories. Any other optional accessories will be packed separately. The weight of the product differs - depending on the type. Due to the size and weight it is recommended to move it by 2 people. After opening the carton, ensure that the content is in good condition and complete. 1.2. PACKAGE CONTENTS Please verify that you received the followin
ページ11に含まれる内容の要旨
User Manual BDL5571V 1.4. PORTRAIT MOUNTING Wall mounting holes Note: The remote control sensor should be Notes: Metric 8 (12mm) screws are needed for wall on the lower side when rotating your monitor. mounting (not included). The mounting interface should comply with the UL1678 standard in North America. The mounting means should be strong enough to bear the weight of the monitor (approx. 38.7 kg without stand). How to use the Logo Guider for Portrait Mode? a. Before
ページ12に含まれる内容の要旨
User Manual BDL5571V 1.5. INSTALLING AND REMOVING STANDS 1.5.1 How to install stands 1. Please turn the monitor off. 2. After inserting the stand in the guide block, tighten the screws on both sides of the monitor. NOTE: The long end of the stand should face to the front while installing. Screw Screw Screw Screw Stands "Longer end comes to the front" 1.5.2 How to remove the stands 1. Spread the protective sheet on a flat surface. 2. Place the monitor face-do
ページ13に含まれる内容の要旨
User Manual BDL5571V 1.5.3 Prevent monitor from falling To prevent the monitor from tipping in the event of an earthquake or other incident, please follow these steps. As shown in the figure below, secure the monitor to a solid wall or pillar using a cord which is strong enough to bear the weight of the monitor (BDL5571V: approx. 47.5 kg). Screw hooks (ring type) are recommended. Screw Hook, etc. Clamper Screw Screw Holes Caution: Although the above method is recommende
ページ14に含まれる内容の要旨
User Manual BDL5571V 2. PARTS AND FUNCTIONS 2.1. FRONT VIEW 1. Remote control sensor, ambient light sensor and power status indicator Receives command signals from the remote control. Detects the ambient lighting condition around the monitor and the image brightness will be auto adjusted when “LIGHT SENSOR” set to “ON” on OSD menu. Indicates the operating status of the monitor: - lights green when the monitor is turned on - lights red when the monitor is in standby mode -
ページ15に含まれる内容の要旨
User Manual BDL5571V 2.2. REAR VIEW 1. POWER button ( ) To switch the power on or put the monitor to standby. 2. MUTE button To switch the audio mute ON/OFF. 3. SOURCE button To set the function while OSD menu is on or to activate input selection menu while OSD menu is off. 4. PLUS (+) button To increase the adjustment while OSD menu is on, or to decrease the audio output level while the OSD menu is off. 5. MINUS (-) button To decrease the adjustment while OSD menu is o
ページ16に含まれる内容の要旨
User Manual BDL5571V Note: Keyboard Control Lock Mode This function completely disables the access to all Keyboard Control functions. To enable the keyboard control lock, press both of “ ” and “ ” buttons and hold down continuously for more than 3 seconds. To recover back to the user mode, press both of “ ” and “ ” and hold continuously for three 3 seconds. 2.3. INPUT/OUTPUT TERMINALS 1. OPTIONAL SLOT Slot for installed optional module e.g. optional DVI module. 2. USB Fo
ページ17に含まれる内容の要旨
User Manual BDL5571V 7. SPEAKERS R/L Outputs the audio signal from the AUDIO IN (AUDIO1/AUDIO2/AUDIO3) or HDMI jack to external speakers. 8. Main power switch Press to switch the main power on/off. 9. AC OUT Connect to the AC IN socket of another BDL5571V monitor or an external media device.(Rating : 100~240Vac, 50-60Hz, 3A Max.) 10. AC IN Connect the supplied power cord to the wall outlet. 11. DISPLAY PORT Connect to the DisplayPort output of a PC or an AV device. 12. VI
ページ18に含まれる内容の要旨
User Manual BDL5571V 2.4. REMOTE CONTROL 2.4.1. GENERAL FUNCTIONS POWER button Press to switch on the monitor from standby mode. Press again to turn it off to standby mode. SMART button To select smart picture mode from: Standard: for images (factory setting) Highbright: for moving image such as Video sRGB: for text based images VIDEO SOURCE button To activate the video source selection menu. Press it repeatedly to select the video input source from DP, DVI-D, VGA, HDMI an
ページ19に含まれる内容の要旨
User Manual BDL5571V DISPLAY button To turn on/off the information OSD displayed on the upper right corner of the screen. MENU button To turn the OSD menu on/off. UP button To move the highlight bar up to adjust the selected item when OSD menu is on. To move the sub-picture up in “PIP” mode. DOWN button To move the highlight bar down to adjust the selected item when OSD menu is on. To move the sub-picture down in “PIP” mode. PLUS button To move the highlight bar right
ページ20に含まれる内容の要旨
User Manual BDL5571V 2.4.2. INSERTING THE BATTERIES IN THE REMOTE CONTROL The remote control is powered by 1.5V AAA batteries. To install or replace batteries: 1. Press and slide to open the cover. 2. Align the batteries according to the (+) and (–) indications inside the case. 3. Replace the cover. Caution: Incorrect use of batteries can result in leaks or bursting. Be careful especially about the following points. Place “AAA” batteries matching the + and - signs on each batte
