ページ1に含まれる内容の要旨
Floor jack
transmission adapter
39152
set up and operating instructions
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sa Ve this manual.
© ®
Copyright 2002, 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this ma
ページ2に含まれる内容の要旨
notice is used to sa Ve this manual address practices Keep this manual for the safety not related to personal injury. warnings and precautions, assembly, caution, without operating, inspection, maintenance and the safety alert cleaning procedures. Write the product’s symbol, is used to address serial number in the back of the manual practices not related to near the assembly diagram (or month personal injury. and year of purchase if product has no number). Keep this manual and t
ページ3に含まれる内容の要旨
when operating the tool. Do not c. maintain the tool with care. Keep use the tool while tired or under a cutting tool sharp and clean. A the influence of drugs, alcohol, or properly maintained tool, with sharp medication. A moment of inattention cutting edges reduces the risk of while operating the tool increases the binding and is easier to control. risk of injury to persons. d. check for misalignment or binding b. dress properly. do not wear loose of moving parts, breakage of clothing o
ページ4に含まれる内容の要旨
for this product is dangerous sYmbols and and can lead to serious injury or property damage. speciFic saFetY 2. if in doubt about the safety of instructions your project, have the work done by a professional familiar with Symbol Definitions applicable safe practices. symbol property or statement 3. Use only with 2-1/4 Ton Floor Jack No-load speed n o (such as SKU 50183 Heavyweight Revolutions or reciprocation per Floor Jack, sold separately). .../min minute 4. Always evaluate your tas
ページ5に含まれる内容の要旨
quickly and safely as possible in Functional description order to avoid injury from the falling load, including getting hit with flying Specifications fragments. Weight Capacity 880 lb. 8. If in doubt about the safety of your 60° Forward project, we advise you to have Base Tilt 10° Backwards the work done by a professional Saddle Pin Diameter .094” familiar with applicable safety For Use Only With 2-1/4 Ton Transmission Jack practices. (SKU 50183 Heavyweight Floor Jack) 9. Use only on
ページ6に含まれる内容の要旨
2. Place each Adjustable Steel Angle (6) 4. The Chain (5) comes assembled to on top of the Base (38) and fasten to one of the Angle Support Brackets. the Base using Bolts (30), Nuts (28) See Figure 2. Use Nut (23), Eye and Washers (29) and finger tighten Bolt Pin, (25) and Wing Nuts (26) on. See Figure 1. to attach Hook Bolt (22) to Support Bracket on opposite corner from 6 Chain. See Figure 3. 26 1 38 25 23, 26 22 28, 29, 30 6 Figure 1 Fi
ページ7に含まれる内容の要旨
7. The bottom of the Base Shaft (18) is general operating instructions then securely placed into the saddle Warning! Verify that Floor Jack is of the Transmission Jack to firmly compatible with this Transmission hold the Transmission Adapter in Jack Adapter before operation. place. See Figure 5. 1. Designate a work area that is clean and well-lit. The work area must not operating instructions allow access by children or pets to read the entire important prevent distraction and inj
ページ8に含まれる内容の要旨
Bolt (22). Turn the nut to retract the centerline is as close to the centerline bolt and hold the transmission snugly. of the engine as possible. 7. Follow the steps in your vehicle’s 6. Begin raising the transmission. Owner’s Service Manual, remove Continue raising it until it is at the drive shaft and any and all mounting installation height. bolts and/or nuts. 7. With the transmission at the correct 8. Depending on type of transmission, height in the transmission tunnel of you may need
ページ9に含まれる内容の要旨
2. before each use, inspect the general inspection , maintenance , condition of the Transmission Jack. and cleaning Check for oil leaks, jack operation, loose components, free rotation Procedures not specifically and pivoting of saddle adjustment explained in this manual components. If a problem occurs, must be performed only by a have the problem corrected before qualified technician. further use. t o preVent do not use damaged equipment. serious injur Y 3. periodically, lubri
ページ10に含まれる内容の要旨
please read the FolloWing careFull Y THE MANUFACTURER AND/OR DISTRIbUTOR HAS PROvIDED THE PARTS LIST AND ASSEMbLY DIAgRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIbUTOR MAkES ANY REPRESENTATION OR WARRANTY OF ANY kIND TO THE bUYER THAT HE OR SHE IS qUALIFIED TO MAkE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/ OR DISTRIbUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACE
ページ11に含まれる内容の要旨
assembl Y diagram 1 2, 3, 4 5 6 7, 8, 9 11 10 12 28, 29, 30 13 27 14 26 35, 36, 37 31, 32, 33, 34 23, 22, 25 22 17 15 16 38 18 19 21 20 SKU 39152 For technical questions, please call 1-800-444-3353. Page 11
ページ12に含まれる内容の要旨
limited 90 da Y WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installat
