ページ1に含まれる内容の要旨
Dear Sceptre Customer,
Congratulations on your new SCEPTRE X32 HDTV purchase. Thank you for
your support. To ensure safety and many years of trouble free operation of
your TV, please read the manual carefully before making any adjustments,
and keep them in a safe place for future references. We hope you enjoy your
new SCEPTRE HDTV.
For technical assistance, please call 1800-788-2878 and select option 3 or
email our tech support group at monitor-ts@sceptre.co
ページ2に含まれる内容の要旨
IMPORTANT INFORMATION - 2 - www.SCEPTRE.com SCEPTRE X32 HDTV User Manual
ページ3に含まれる内容の要旨
SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and / or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning t
ページ4に含まれる内容の要旨
SAFETY INSTRUCTIONS This product is designed and manufactured to operate within defined design limits, and misuse may result in electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of the product. Read the following safety instructions before operating the display. Keep these instructions in a safe place for future reference. • To avoi
ページ5に含まれる内容の要旨
• Do not overload power strips and internal components may function extension cords. Overloading can abnormally. Unplug the power cord result in fire or electric shock. immediately and contact your dealer • The wall socket should be installed for repair. Continued use of the near the equipment and should be product may cause fire or electric easily accessible. shock. • Only the marked power source can be • Do not install the product in an area used for the product. Any power with heavy du
ページ6に含まれる内容の要旨
IMPORTANT INFORMATION Television Antenna Connection Protection External Television Antenna Grounding If an outside antenna or cable system is to be connected to the TV, make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and static charges. Article 810 of the National Electrical Code, ANSI/NFPSA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in
ページ7に含まれる内容の要旨
Opening the Package The SCEPTRE TV is packaged in a carton. Any standard accessories are packed separately in another carton. The weight of the TV is approximately 23.5 lbs. Due to the size and weight of the product, it is suggested that it must be handled by a minimum of 2 or more persons. Since the glass can be easily scratched or broken, please handle the product gently. Never place the unit on a surface with the glass facing downwards unless it is on protective padding. When op
ページ8に含まれる内容の要旨
Attaching or Removing the Stand 1. To remove the stand, remove the 4 screws in the circled area and the stand will come off. 2. To attach the stand place the display unit flat on a table. Afterwards attach the neck piece onto the display by matching the two protruding clips and inserting them in. Screw in the 4 screws to secure the neck. Do not over torque the type 2 screws. It will strip the plastic threading.
ページ9に含まれる内容の要旨
3. Attach the base onto the neck matching the 5 holes and screw in the type 2 screws. Do not over torque the type 2 screws. It will strip the plastic threading. - 9 - www.SCEPTRE.com SCEPTRE X32 HDTV User Manual
ページ10に含まれる内容の要旨
Table of Contents IMPORTANT INFORMATION...........................................................................................................2 SAFETY INSTRUCTIONS ................................................................................................................3 SAFETY INSTRUCTIONS ................................................................................................................4 IMPORTANT INFORMATION.....................................................
ページ11に含まれる内容の要旨
Identifying Front and Rear Panel Front View INDICATOR LIGHT – The light is red when power is plugged in but the TV is not turned on. The light turns blue when the TV is turned on. Because of the LCD in the panel, the TV might take 10 – 12 seconds to power on. REMOTE SENSOR – The remote sensor receives all the commands from the remote control. Rear View Mounting Pattern Mounting Specification : 200mm x 200mm using screw size M5
ページ12に含まれる内容の要旨
Side Control Buttons 1. VOL(+) – This button increases the TV’s volume. If a sub-menu is active, pressing this button will move the select right. 2. VOL(-) – This button decreases the TV’s volume. If a sub-menu is active, pressing this button will move the selection left. 3. CH( ▲) – This button changes the TV channel up. If the OSD is active, this button functions as up for the menu. 4. CH( ▼) – This button changes the TV
ページ13に含まれる内容の要旨
Rear View Connections 1. SPDIF - This connection port is used for sending out digital audio signals to digital surround sound receivers. The orange (COAX SPDIF OUT) connector sends out either bit-stream or PCM digital sound signal to a home theater receiver with digital coax input. 2. TV – This connection is for digital or analog cable without the cable box or over-the-airwave antennas. The tuner is a hybrid tuner that tunes to both
ページ14に含まれる内容の要旨
7. Analog Audio Out – This connection is for connecting to analog audio receivers. 8. Video – Video connects to devices that use composite video cables such as VCR or DVD player or Wii™. Connect the yellow for video and the red / white for audio. This port shares the audio jacks with YPbPr. 9. YPbPr – This connection port is for DVD players or satellite / cable set- top boxes that use component cables. From left to right, connect green, blue, and red for video, and then connect white fo
ページ15に含まれる内容の要旨
SCEPTRE X32 Remote Control This remote control follows SONY’s universal remote code. To find the actual code you need to consult your cable or satellite tech support. - 15 - www.SCEPTRE.com SCEPTRE X32 HDTV User Manual
ページ16に含まれる内容の要旨
For universal remotes, this TV follows SONY’s universal remote code. You need to find the actual code from your cable or satellite or universal remote provider. 1. POWER – Turns the TV on or off. 2. SOURCE – Press this button to cycle through the INPUT source. 3. CC – Cycles between different closed captioning modes. 4. MTS – Selects stereo, mono, or second audio programming. 5. MUTE – Turns the sound off from the TV. To un-mute either press VOL(+) or press the MUTE button again. 6.
ページ17に含まれる内容の要旨
Connection Suggestions If You Have Digital Cable without Cable Box or Antenna… 1. Make sure the power of HDTV is turned off. 2. Connect the Coaxial RF cable from your antenna or digital cable to the TV port on the back of your HDTV. 3. Turn on the HDTV. 4. Follow the first time on screen instructions. Please Note : • Not all broadcasts are in High Definition (HD). Please refer to your local broadcasting stations for more information.
ページ18に含まれる内容の要旨
Connecting DVD Player with Component YPbPr… 1. Make sure the power of HDTV and your DVD player is turned off. 2. Obtain a Component Cable. Connect the green color connector to both your DVD player and YPbPr’s green connector port on the back of your HDTV. 3. Connect the blue color connector to both your DVD player and YPbPr’s blue connector port on the back of your HDTV. 4. Connect the red color connector to both your DVD player and YP
ページ19に含まれる内容の要旨
Connecting Wii™ with Composite… 1. Make sure the power of HDTV and your Wii™ is turned off. 2. Obtain a Yellow Video Cable. Connect the Yellow Video connector to both your Wii™ and AV’s Yellow Video connector port on the back side of your HDTV. 3. Obtain a RCA Audio Cable. Connect the white color connector to both your Wii™ and AV’s white connector port on the back side of your HDTV. 4. Connect the red color connector to both your Wii
ページ20に含まれる内容の要旨
Connecting Cable or Satellite boxes with HDMI… 1. Make sure the power of HDTV and your set-top box is turned off. 2. Connect a HDMI cable to the HDMI output of your set-top box and the other end to the HDMI port on the back of your HDTV. 3. Turn on the HDTV and your set-top box. 4. Use the remote control’s source button or the source button on the TV to switch to HDMI. Please Note : • Please reference the set-top box’s manu
