ページ1に含まれる内容の要旨
X9C-NagaV
User’s Manual
ページ2に含まれる内容の要旨
FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonab
ページ3に含まれる内容の要旨
The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN61000- 3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio int
ページ4に含まれる内容の要旨
TABLE OF CONTENTS TABLE OF CONTENTS ..........................................................................................III Your New LCD Monitor 1 Unpacking 1 Identifying Components 3 Adjusting the Tilting Angle 5 Connecting AC Power and Video Cable 6 Power Management System 6 The LCD Monitor’s Control Panel 7 Adjusting the Monitor’s Display 8 TFT LCD Monitor Specifications 14 Supported Timing 16 Troubleshooti
ページ5に含まれる内容の要旨
The LCD Monitor Your New LCD Monitor Your LCD Monitor has been designed to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640x400 VGA to 1280x1024 SXGA. The digital controls located on the front panel allow the user to easily adjust the Monitor’s display parameters, and the LCD Monitor’s small footprint gives you more room in your workspace for other peripherals. Lightweight and compact, the LCD Monitor is the perfect solution
ページ6に含まれる内容の要旨
After unpacking your LCD monitor, make sure the following items are included in the box and are in good condition: • LCD monitor • Power Cord • Monitor-To-PC Analog signal cable 15pin • Monitor-To-PC DVI signal cable • 1.5M stereo Jack Audio Cable • User’s manual If you find that any item to be missing or appear to be damaged, contact your dealer immediately. Do not throw away the packing material or shipping carton in case you need to ship or store the LCD monitor in the fut
ページ7に含まれる内容の要旨
Identifying Components A. The LCD Monitor — Front View 3 1 4 2 Figure 1-1: The LCD Monitor Front View 1. Power-On Indicator This Circular LED indicator green lit when the power is on and orange lit when the LCD monitor is in power-saving mode. 2. Monitor Stand 3. LCD Screen The LCD monitor screen is a 19-inch TFT 1280 x 1024 screen. 4. LCD Monitor Control Panel Refer to Chapter 2 for more details. 3 Rev.1
ページ8に含まれる内容の要旨
B. "Hot Keys" for Quick Adjustment of Monitor Settings + P Figure 1-2: "Hot Keys" 1. Volume Adjustment "hot key": Press this + button to allow you to adjust the volume of the LCD Monitor directly 50 2. Contrast Adjustment “ Hot key” Press this - button to allow you to adjust the contrast of the LCD Monitor directly 50 3. Auto adjustment “ Hot Key “ Press th
ページ9に含まれる内容の要旨
Adjusting the Tilting Angle The LCD Monitor’s angle settings range from 0 ° to 10 °. 0 to 10 10 Figure 1-3: Tilting the Monitor 5 Rev.1
ページ10に含まれる内容の要旨
Connecting AC Power and Video Cable Note: Turn off your PC and the LCD monitor before connecting your LCD monitor to the computer. AC-IN AC Outlet (Wall Socket) Computer Power Cord Audio cable DVI VGA Figure 1-4: The AC Adapter Power Management System This LCD Monitor complies with the VESA DPMS power management proposal. When the LCD Monitor is in power-saving mode or detects an incorrect timing, the monitor screen will be blank and the power LED indicator from green lit change to
ページ11に含まれる内容の要旨
The Display Controls The LCD Monitor’s Control Panel + P Figure 2-1: The Control Panel 1. : Enable the OSD Menu button or / Move the cursor to the left (when OSD is enabled) 2. : Move the cursor to the Right ( When OSD is enabled) / Auto-adjustment hot key 3. - : Enter into the sub-menu or decrease the value / Contrast hot key 4. + : Enter into the sub-menu or increase the value / Volume hot key 5. : Power Switch This button lets y
ページ12に含まれる内容の要旨
Adjusting the Monitor’s Display OSD Main Menu 1. Pressing the button causes the screen below to appear. 2. Use the & key to select the desired group, then press – or + key to enter into sub-menu 3. Repeat step 2 to select the changed item, then – or + to change the value. Timing : 1280 x 1024 V/H Freq : 74.6Hz 79KHz SCEPTRE X9C-NagaV The OSD Main Menu OSD Main SCREEN 8 Rev.1
ページ13に含まれる内容の要旨
Auto Adjust Option The Auto Adjust option lets the monitor determine and select the settings that are most appropriate for your system requirements. Note: it only apply for Analog RGB input Provides you with the current display timing information. Brightness and Contrast Adjustment Adjusts the Brightness value Adjusts the Contrast value Execute the white balance function Return to the previous Menu Audio Function Vo
ページ14に含まれる内容の要旨
Set up the color temperature value User Mode Sets the color temperature to 6500K Sets the color temperature to 9300K Red change Red gain for the color temperature (only valid when color temperature set at user mode ) Green change Green gain for the color temperature (only valid when color temperature set at user mode ) Blue change Blue gain for the color temperatur
ページ15に含まれる内容の要旨
Adjusts phase tracking to reduce display flicker Moves the whole screen right or left Moves the whole screen up or down Return to the previous Menu OSD Adjustment Restores settings to factory default values Sets the OSD timer Moves the OSD menu horizontally Moves the OSD menu vertically Set the graphic mode or text mode Return to the previous Menu Port Select Set analog port for PC signal input
ページ16に含まれる内容の要旨
Set DVI port for PC signal input Return to the previous Menu Exit the OSD screen 12 Rev.1
ページ17に含まれる内容の要旨
Note: 1) No video When the monitor is ON and there is no video signal received, the following message will be displayed 2) Signal out of range When the frequency range of the signal is out of the Monitor’s specifications, (over 85HZ) the display will show the following message Out of Range 13 Rev.1
ページ18に含まれる内容の要旨
Appendix A TFT LCD Monitor Specifications Item Specification LCD Panel 19" SXGA Control Software Power switch with LED indicator Functions (ON/OFF) Power On-Screen Main Menu Submenu Display Information (OSD) Brightness Brightness/Contrast/White /Contrast Control balance/Exit Audio Control Volume/Mute/Exit Color temperature User mode, 9300K, 6500K Control R,G,B, gain value Display Quality Auto Adjustment/Phase adjustment/Screen Size/ Screen Horizontal position/Screen Verti
ページ19に含まれる内容の要旨
Item Specificaiton Scanning Frequency 24-80K H/V, Hz 50-75 Power Management Meets VESA DPMS Power Consumption 37W/1W Max. (ON/OFF, W) Dimensions 16.54 x 16.4 x 6.81 in. WxHxD (420.2 x 416.5 x 173mm) Net Weight 11 lbs (approx.) (5 Kg) Power Supply Universal Input AC Socket Environment Operating Temperature: 32 to 104°F (0 to 40° C) Relative Humidity: 10% to 90% Regulatory FCC B DoC,UL/cUL,Energy star 15
ページ20に含まれる内容の要旨
Appendix B Supported Timing Vertical Horizontal Item Standards Resolution Dot Clock Scanning Scanning (MHz) Frequency Frequency (Hz) (kHz) 1 NEC PC98 640x400 21.05 56.42 24.83 2 MAC 13" mode 640x480 30.24 66.67 35.00 3 MAC 16" mode 832x624 57.28 74.55 49.73 4 MAC 17" mode 1024x768 80.00 75.02 60.24 5 VGA 640x350 25.18 70.09 31.47 6 VGA 640x400 25.18 70.09 31.47 7 VGA 640x480 25.18 59.94 31.47 8 VESA 640x480 31.50 72.81 37.86 9 VESA 640x480 31.50 75.00 37.50 10 VESA 800x600 3
