ページ1に含まれる内容の要旨
®
ViewSonic
VX922
LCD Display
ページ2に含まれる内容の要旨
Contents TCO Information.......................................................................................... i Compliance Information.............................................................................. 1 Important Safety Instructions...................................................................... 2 Copyright Information ................................................................................. 3 Product Registration....................................................
ページ3に含まれる内容の要旨
TCO Information Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of go
ページ4に含まれる内容の要旨
Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO Development’s website http://www.tcodevelopment.com or may be ordered from: TCO Development SE-114 94 STOCKHOLM, Sweden Fax: +46 8 782 92 07 E-mail: development@tco.se Information regarding TCO’99 approved and labelled products may also be obtained at http://www.tcodevelopment.com Ecological requirements Flame retardants Flame retardants may b
ページ5に含まれる内容の要旨
Compliance Information For U.S.A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there i
ページ6に含まれる内容の要旨
Important Safety Instructions 1. Read these instructions completely before using the equipment. 2. Keep these instructions in a safe place. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this equipment near water. 6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the Display” in this guide for further instructions. 7. Do not block any ventilation openings. Install the equipment in accordance with the manufacturer’s instructions. 8. Do not install ne
ページ7に含まれる内容の要旨
Copyright Information ® Copyright © ViewSonic Corporation, 2005. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Asso
ページ8に含まれる内容の要旨
Getting Started ® Congratulations on your purchase of a ViewSonic LCD display. Important! Save the original box and all packing material for future shipping needs. NOTE: The word “Windows” in this user guide refers to the following Microsoft operating systems: Windows ‘95, Windows NT, Windows ‘98, Windows 2000, Windows Me (Millennium), and Windows XP. Package Contents Your LCD display package includes: • LCD display • Power cord • Video cable • ViewSonic Wizard CD-ROM • Quick Start Guide NOTE: T
ページ9に含まれる内容の要旨
Quick Installation 1. Remove two rear panel covers • Wait for the CD-ROM to auto-start. 2. Connect power cord (and AC/DC NOTE: If the CD-ROM does not auto- adapter if required) start: double-click on the CD-ROM icon in the Windows Explorer, then double-click 3. Connect video cable on viewsonic.exe. • Make sure both the LCD display and • Follow the on-screen instructions. computer are turned OFF. 6. Windows users: Set the timing mode • Connect the video cable from the LCD (resolution and refresh
ページ10に含まれる内容の要旨
Wall Mounting (Optional) ® To obtain a wall-mounting kit, contact ViewSonic or your local dealer. Refer to the instructions that come with the base mounting kit. To convert your LCD display from a desk- mounted to a wall-mounted display, do the following: 1. Verify that the Power button is turned OFF, then disconnect the power cord. 2. Lay the LCD display face down on a towel or blanket. 3. Remove the rear panel covers from the back of the LCD display. 4. Remove the four screws attaching the ba
ページ11に含まれる内容の要旨
Using the LCD Display Setting the Timing Mode Setting the timing mode is important for maximizing the quality of the screen image and minimizing eye strain. The timing mode consists of the resolution (example 1280 x 1024) and refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the OSD (On-screen Display) controls to adjust the screen image. For the best picture quality set your LCD display timing mode to: VESA 1280 x 1024 @ 60Hz. To set the Timing Mode: 1. Set
ページ12に含まれる内容の要旨
Adjusting the Screen Image Use the buttons on the front control panel to display and adjust the OSD controls which display on the screen. The OSD controls are explained at the top of the next page and are defined in “Main Menu Controls” on page 10. Main Menu with OSD controls Front Control Panel shown below in detail Scrolls through menu options and adjusts the displayed control. Also a shortcut to display the Contrast adjustment control screen. Displays the Main Displays the control screen
ページ13に含まれる内容の要旨
Do the following to adjust the display setting: 1. To display the Main Menu, press button [1]. NOTE: All OSD menus and adjustment screens disappear automatically after about 30 seconds. This is adjustable through the OSD timeout setting in the setup menu. 2. To select a control to adjust, press or to scroll up or down in the Main Menu. 3. After the desired control is selected, press button [2]. A control screen like the one shown below appears. The line at the bottom of the screen shows the
ページ14に含まれる内容の要旨
Main Menu Controls Adjust the menu items shown below by using the up and down buttons. Control Explanation Auto Image Adjust automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion. Press the [2] button to obtain a sharper image. NOTE: 1. Auto Image Adjust works with most common video cards. If this function does not work on your LCD display, then lower the video refresh rate to 60 Hz and set the resolution to its pre-set value. 2. The Auto Image Ad
ページ15に含まれる内容の要旨
Control Explanation 6500K-Adds red to the screen image for warmer white and richer red. 5400K-Adds green to the screen image for a darker color. User Color Individual adjustments for red (R), green (G), and blue (B). 1. To select color (R, G or B) press button [2]. 2. To adjust selected color, press or . Important: If you select RECALL from the Main Menu when the product is set to a Preset Timing Mode, colors return to the 6500K factory preset. Information displays the timing mode (video signa
ページ16に含まれる内容の要旨
Control Explanation The Manual Image Adjust controls are explained below: H./V. Position (Horizontal/Vertical Position) moves the screen image left or right and up or down. H. Size (Horizontal Size) adjusts the width of the screen image. Fine Tune sharpens the focus by aligning the text and/or graphics with pixel boundaries. Sharpness adjusts the clarity and focus of the screen image. Setup Menu displays the menu shown below: The Setup Menu controls are explained below: Language Select allows th
ページ17に含まれる内容の要旨
Control Explanation OSD Timeout sets the length of time the OSD screen is displayed. For example, with a “15 second” setting, if a control is not pushed within 15 seconds, the display screen disappears. OSD Background allows the user to turn the OSD background On or Off. Memory Recall returns the adjustments back to factory settings if the display is operating in a factory Preset Timing Mode listed in the Specifications of this manual. Exception: This control does not affect changes made with
ページ18に含まれる内容の要旨
Other Information Specifications LCD Type 19” (full 19" viewable diagonal area), TFT (Thin Film Transistor), Active Matrix SXGA LCD, 0.294 mm pixel pitch Color Filter RGB vertical stripe Glass Surface Anti-Glare Input Signal Video RGB analog (0.7/1.0 Vp-p, 75 ohms) Sync Composite Sync, Separate Sync, Sync on Green TMDS Digital (100ohms) f :30-82 kHz, f :50-85 Hz h v Compatibility PC Up to 1280 x 1024 Non-interlaced 1 Power Macintosh up to 1280 x 1024 Macintosh Resolution Recommended 1280 x 1024
ページ19に含まれる内容の要旨
Troubleshooting No power • Make sure power button (or switch) is ON. • Make sure A/C power cord is securely connected to the LCD display. • Plug another electrical device (like a radio) into the power outlet to verify that the outlet is supplying proper voltage. Power is ON but no screen image • Make sure the video cable supplied with the LCD display is tightly secured to the video output port on the back of the computer. If the other end of the video cable is not attached permanently to the LCD
ページ20に含まれる内容の要旨
Customer Support For technical support or product service, see the table below or contact your reseller. NOTE: You will need the product serial number. T = Telephone Country/Region Website Email F = FAX T= (800) 688 6688 United States www.viewsonic.com/support service.us@viewsonic.com F= (909) 468 1202 Canada www.viewsonic.com/support T= (886) 463 4775 service.ca@viewsonic.com United Kingdom www.viewsoniceurope.com/uk T= 0207 949 0307 Europe, Middle East, Baltic countries, and www.viewsoniceuro
