ページ1に含まれる内容の要旨
BeefEater
AUSTRALIA
Signature Plus
NEW ZEALAND
Signature S-3000E
UNITED STATES
Signature S-3000S
Balcony CANADA
BeefEater Gas Barbecues
Assembly, Installation and Operating Instructions
Certified ISO 9001 : 2000 by
9800958
IMPORTANT: FOR YOUR SAFETY
• BeefEater Barbecues are approved for OUTDOOR USE ONLY and If you smell gas:
must not be used in a building, garage or any other enclosed area.
1. Shut off gas to the appliance.
• BeefEater Barbecues must not be used in recreational vehicles or
2.
ページ2に含まれる内容の要旨
2 Table of Contents Beefeater Barbecues 3 Safety Warnings Dimensions and Specifications 19 12 6 - 9 Assembly & Installation Spare Parts 20 - 21 Instructions Help Guide 14 BBQ Accessories 24 Operation Instructions 10 -13 Outdoor Installation 18 Cleaning and Maintenance 15 - 17 Gas Cylinder Information 4 - 5 Tech Support 24 WARNING: We want you to enjoy your barbecuing experience - Failure to follow the instructions and observe the warnings provided in this operating manual could result in serio
ページ3に含まれる内容の要旨
3 Precautions and Warnings BeefEater Barbecues DO NOT DO • Lean over barbecue when lighting. • Spanner tighten all gas fittings as per instructions. • Leave cooking food unattended. • Check all gas hoses and line connections for damage, cuts or cracks each time the appliance is to be used. • Delay lighting burners after turning gas on. • Always leak test with a solution of soapy water. • Spray or store aerosols in vicinity of barbecue whilst in operation. • Check main opening, throat and ven
ページ4に含まれる内容の要旨
4 Gas Cylinder Information Beefeater Barbecues Gas Cylinder Safety Information Standard POL Regulator This appliance is designed to be used with a gas Fig 1 Gas Shutoff Valve cylinder not exceeding 9KG (20lbs) capacity. The Gas cylinder must be constructed and marked in accordance with specifications for LP Gas Cylinders of the:(USA) U.S. Dept. of Transportation (DOT) or Tighten in this direction Bleeder valve screw the National Standard of Canada, CAN/CSA - B339, Cylinders, Spheres or Tubes
ページ5に含まれる内容の要旨
5 Gas Cylinder Information BeefEater Barbecues Tools Required You will need the following tools to assemble 19mm your barbecue. 19mm Spanner (wrench) for Gas Inlet Connection 10mm 10mm Spanner (wrench) All body nuts Phillips Head Screwdriver Note: Important: Always use the correct size spanner (wrench) to tighten Always check the gas label on the appliance to gas fittings. Ensure that all gas fittings are spanner ensure that you have the correct gas configuration tightened and then leak test
ページ6に含まれる内容の要旨
6 Assembly Instructions Beefeater Barbecues Assembly Notes Assembly Procedure Before any assembly or installation is attempted it is Heat Reflectors, Burners And Vaporizers important that you check for damage or missing parts. Your The modular Vaporizer Grid system has been designed to dealer or the manufacturer must be notified of any problems maximise the performance of your BeefEater barbecue immediately before proceeding. The reflectors fit between each burner. They reflect heat The ma
ページ7に含まれる内容の要旨
7 Assembly Instructions BeefEater Barbecues Fitting The Heat Reflectors Fitting The Vaporizers Completely remove all of the plastic film from the reflectors. Remove the protective plastic film from each Vaporizer and The tabbed ends of the heat reflectors face forward to the then fit the Vaporizers to the barbecue. The tabbed ends front of the barbecue frame. The tabs fit into the slots in of the Vaporizers face forward to the front of the barbecue the front end of the barbecue (behind the c
ページ8に含まれる内容の要旨
8 Assembly Instructions Beefeater Barbecues Assembly Procedure (Continued) Fitting The Cooking Plates And Grills We recommend fitting the plate to the left-hand side of the barbecue frame (with the drain hole to the extreme left). The grill or grills can be fitted to the right hand side of the barbecue frame. Grills must always be positioned over the Vaporizer grids. See Fig 13. 1 BeefEater 2, 3 & 4 burner barbecues come standard with / 2 1 plate and /2 grill and are approved for use wit
ページ9に含まれる内容の要旨
9 Installation Instructions BeefEater Barbecues Recommended minimum LPG cylinder capacity for use with Important this appliance is 4kg. Maximum LPG cylinder capacity for This appliance must be installed in accordance with use with this appliance is 10kg. the installation requirements of the LOCAL GAS and Do not install the gas cylinder beneath the barbecue unless ELECTRICITY supply authority, or the appropriate installation in conjunction with an approved separator panel. code issued by t
ページ10に含まれる内容の要旨
10 Operating Instructions Beefeater Barbecues Before Lighting After Use 1. Check that all gas hose fittings and connections are 1. Be sure to turn off all control knobs and cylinder valve spanner tight. Gas regulators that are fitted with a hand (for Propane - LPG) or shut-off valve (for Natural Gas). tightening wheel should be checked to ensure that the 2. Clean drip tray, griddle plates and grills if necessary . connection is secure. Allow barbecue to cool before replacing the weather cover
ページ11に含まれる内容の要旨
11 Operating Instructions BeefEater Barbecues Preheating Guide Manual Lighting 2, 3, 4 and 5 burner barbecue Turn on desired number of 1. Press and turn the left hand control knob counter- burners to the High position for approximately ten minutes clockwise to the “High” position, then light the left hand or until the cooking surfaces are heated. burner immediately through the gap between the front of the drip tray and the barbecue body . Cooking With Optional The BeefEater Note: If the
ページ12に含まれる内容の要旨
12 Operating Instructions Beefeater Barbecues Cooking With The BeefEater Roasting Hood cont. If you are cooking a roast, it is always a good idea to use a roast holder and baking dish. This will keep the meat away Temperature Warnings from the direct heat source but allow the meat to cook by Do not exceed the temperature warning on the temperature convection. (This is essential in the case of the 2 burner gauge. barbecue where the meat tray will be sitting over direct heat). Note: Do not
ページ13に含まれる内容の要旨
13 Operating Instructions BeefEater Barbecues Operation Of The Optional Side Burner Warning When using the side burner ensure that any handle fitted to Lighting a wok, pot or pan is positioned so that it is out of reach of 1. Check the control knob is in the Off position and ensure children. the gas line is properly connected. 2. Raise the lid and check that the burner and burner cap Warning - Safety With Woks And Pots are in the correct position. And Pans 3. Press and turn the control kno
ページ14に含まれる内容の要旨
14 Help Guide Beefeater Barbecues Your BeefEater barbecue has undergone a series of quality checking points prior to leaving the factory. Should you have a problem with your appliance please refer to the help guide below before calling your dealer or service person. Important - Shut off the gas supply before performing any checks. Problem Cause Check Barbecue will not light Ignition system not working Check to see visible spark at starter probe - if no spark is present when control knob is tur
ページ15に含まれる内容の要旨
15 Care and Maintenance BeefEater Barbecues Care And Maintenance Instructions Cleaning The Cooking Surfaces Each system has specific care, cleaning and maintenance Cooking Surface Preparation requirements so it is important to read the correct Before Using Your BeefEater Barbecue instructions for the system supplied with your barbecue. Your BeefEater barbecue will feature either of the following Standard Cast Iron Grills - Non Porcelain Coated cooking surfaces. Many food acids, marinades,
ページ16に含まれる内容の要旨
16 Care and Maintenance Beefeater Barbecues or vegetable cooking spray after each use will help to • Coat the grills with a layer of cooking oil. This will protect the grills between barbecuing sessions. . Do not clean the reduce surface rust and prolong plate and grill life. The surface coating will wear off in time and cast iron will cooking grills in a dishwashing machine. • Do not use highly caustic, harsh or abrasive chemical rust (this is not covered by warranty). 4. Burners: Check ma
ページ17に含まれる内容の要旨
17 Care and Maintenance BeefEater Barbecues avoid unwanted marks. occur on any exposed metal surface if it is not protected from the elements. Even stainless steel can be affected by Near the ocean or salt-water environment, wash regularly, long term exposure to the elements. To prevent exposure to rinse and then dry before covering. Covering a salt sprayed the elements, store your barbecue, hood and trolley under stainless steel product while still wet will allow salt deposits to form, c
ページ18に含まれる内容の要旨
18 Outdoor Installation Instructions Beefeater Barbecues 12 We recommend that this installation be done in a masonry WARNING: Contact your local municipality for any structure and carried out by a professional tradesperson. Other building codes regulating the installation of outdoor non-combustible material such as Hardiplank, Villaboard with barbecue appliances. Outdoor installations must metal studs may also be used. conform to local codes or, in the absence of local codes, with the fol
ページ19に含まれる内容の要旨
19 Specifications BeefEater Barbecues 12 Australia’s Leading Barbecue
ページ20に含まれる内容の要旨
Signature S3000 Balcony Signature S3000 Signature S3000 20 Signature Series Spare Parts Beefeater Barbecues 2 Burner Balcony 3 Burner Signature S3000 S/E 21 21 3 3 8 * 8 * 9 * 4 4 9 4 * 3 7 7 5 5 5 5 6 5 6 11 6 10 6 1 17 11 6 20 12 13 1 17 16 13 11 10 14 2 11 13 16 11 14 2 14 20 14 16 15 12 14 16 13 16 15 4 Burner Signature S3000 S/E 5 Burner Signature S3000 S/E 21 21 8 8 * * 3 3 9 9 * * 3 3 3 4 4 7 4 7 4 4 4 5 5 4 5 5 6 5 6 5 6 5 6 5 6 6 6 6 20 20 1 1 10 11 17 11 17 11 13 11 11 10 13 11 11 11
