ページ1に含まれる内容の要旨
OUTDOOR GAS BARBEQUE
OWNER’S MANUAL
This manual is for use with Jackson Grills 3 & 4 Burner Models
MODELS JG3 AND JG4
MODELS JG3 AND JG4
Warning: Please read and understand the contents of this manual fully before operating.
Failure to do so may result in fire or explosion. Homeowners should retain these
instructions.
CONTENTS
CONTENTS
A Message to our Customers.................. 2
Safety....................................................3
Installati
ページ2に含まれる内容の要旨
A special message to our customers Thank you for choosing the Jackson Grill for your new gas grill. This appliance is designed with quality components and we are confident that it will provide you with years of excellent operation. Please take the time to read the whole manual and familiarize yourself with all of the features of the Jackson Grill. This manual also contains important safety information and operation instructions. Ensure that this manual remains handy to the barbeque fo
ページ3に含まれる内容の要旨
3. This appliance must not be operated SAFETY unattended. Your new Jackson Grill barbeque is a safe, 4. Special care must be taken to keep convenient appliance when used and small children away from heated maintained properly. As with all gas-fired surfaces. appliances, certain safety precautions must be observed. Failure to follow ELECTRICAL CAUTION these precautions may result in damage or injury. If you have any questions or concerns regarding the 1. If any accessory i
ページ4に含まれる内容の要旨
QCC-1 Quick Closing Coupling system. CLEARANCES The QCC-1 system incorporates new safety features required by the Canadian 1. The appliance must have a minimum Standards Steering Committee and the horizontal clearance from sides and American National Standards Institute back of unit to adjacent vertical (ANSI). combustible construction below and extending above the top of the unit 36 Gas will not flow until a positive inches from sides and 36 inches from connection has been m
ページ5に含まれる内容の要旨
or the US Department of Transport position. Protect the valve from (DOT) for use in the USA. accidental damage. 2. The LP gas cylinder used for this 3. Do not tip the LP gas cylinder while appliance must not have a capacity connecting it to the regulator. Fasten larger than 20 lb. (9 kg): the cylinder securely during transport, use and storage. approximately 18” (46cm) high & 12” (30cm) diameter. 4. If the cylinder is tipped after it is connected to the regulator, shut off 3. Al
ページ6に含まれる内容の要旨
OPERATION IDENTIFICATION 1. Never connect your gas grill to an LP To identify these cylinders, the new OPD cylinder without the regulator handwheel has been standardized to the provided, and never to an shape shown. unregulated gas supply. The gas regulator supplied with the appliance must be used. 2. Always leak test the LP gas cylinder to regulator connection when connecting the LP gas cylinder to the appliance. See “leak testing”. 3. Do not operate the appliance if the sm
ページ7に含まれる内容の要旨
gas only. The hose and hose couplings until there is a positive stop. Do not comply with CGA Standard CAN 1.83. use tools. Hand tighten only. No modifications or substitutions When making the connection, hold should be attempted. the regulator in a straight line with the cylinder valve, so as not to 4. Protect the hose from dripping grease cross thread the connection. and do not allow the hose to touch any hot surface, including the base 4. Leak test the connection. See “leak of
ページ8に含まれる内容の要旨
NATURAL GAS INSTALLATIONS The outdoor cooking gas appliance and its’ individual shut off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ LEAK TEST psi (3.5 kPa). 1. DO NOT USE OR PERMIT SOURCES The outdoor cooking gas appliance must OF IGNITION IN THE AREA WHILE be isolated from the gas supply by closing DOING THE LEAK TEST. THIS its’ individual manual shut off valve during INCLUDES SM
ページ9に含まれる内容の要旨
This will allow the orifices to disengage 5. Clean the outside of the burners with a from the burner venturi. wire brush and make sure all gas ports are clear. Use a straight coat hanger 6. Unscrew each gas valve and re-install to clear any obstructions. new natural gas valves and orifices. Use teflon tape or pipe dope when 6. Use a flashlight to look into the venturi installing valves and orifices. end of the burner to check for blockages. If necessary, use a straight coat hanger
ページ10に含まれる内容の要旨
charred remains with a wire brush or 1. Remove the cooking grates and the scraper. flame tamers that are over each burner. When used for the first time, the grill will emit a slight odor. This is a normal and 2. Turn the burner you are lighting to temporary condition caused by the burn-in high / light and place a long match of internal paints and lubricants used in near the side gas ports of the burner. the manufacturing process and should not occur again. Simply run the main burner
ページ11に含まれる内容の要旨
LIGHTING INSTRUCTIONS OPEN LID Ensuring all burner controls are in the off position, slowly ┌ ┐ turn on the gas supply valve. MAIN BURNER REAR BURNER LIGHTING LIGHTING Turn any main burner control Remove warming rack. to high position. Depress Igniter button and Turn rear burner control to hold or light with a match. high positionand light with a match. If ignition is not immediate, If ignition is not immediate, turn burner control off. Wait turn burner
ページ12に含まれる内容の要旨
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSES SOLUTION Low heat or low flame when For propane – improper lighting Ensure lighting procedure is valve turned to high. procedure. followed carefully. All gas grill valves must be in the off position when the tank valve is turned on. Turn tank on for all pressure to equalize. See lighting instructions. For natural gas – undersized Pipe must be sized according to supply line. installation code. For both gases – improper pre- Pre-heat grill
