ページ1に含まれる内容の要旨
EVENTS
D320PL DIGITIZER
R9851550
OWNER’S MANUAL
13122002 R5976470/01
ページ2に含まれる内容の要旨
Barco nv Events Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.89.70 Fax: +32 56.36.88.24 E-mail: events@barco.com Visit us at the web: www.barco.com Printed in Belgium
ページ3に含まれる内容の要旨
Copyright © All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of BARCO. Guarantee and Compensation Barcoprovidesaguaranteerelatingtoperfectmanufacturingaspartofthelegallystipulatedtermsofguarantee. Onreceipt,thepurchasermustimmediatelyinspectalldeliveredgoodsfordamageincurredduringtransport,as wellasformaterialandmanufacturingfaultsBarcomustbeinfo
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
Table of contents TABLE OF CONTENTS 1. Safety..................................................................................................3 1.1ImportantSafetyInstructions....................................................................................3 1.2ImportantWarnings...............................................................................................4 2. Introduction..........................................................................................7 2.1Generalfunct
ページ6に含まれる内容の要旨
Table of contents 2 R5976470 D320PL DIGITIZER 13122002
ページ7に含まれる内容の要旨
1. Safety 1. SAFETY 1.1 Important Safety Instructions Instructions: Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do NOT submerge fully or partly in water or other liquids. Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. Consultthemanufacturerforfurtheradviceshouldanydoubtsexistregardinganycleaningprocedure. Do not block ventilation openings. Install in accordance with the manufacturer
ページ8に含まれる内容の要旨
1. Safety 1.2 Important Warnings Important Warnings: Risk of electric shock: Image 1-1 Risk of electrical shock Risk of electric shock. Do not open. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightningflashwithan arrowhead within atriangleisintendedto telltheuserthatpartsinsidethis product may cause a risk of electrical shock to persons. The exclamation point within a triangle is int
ページ9に含まれる内容の要旨
1. Safety Use of an extension cord: If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating. Also make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes. Cabinet openings: Never push objects of any kind into this product through cabinet slots as they may touch dangerous high voltage points or short out parts that cou
ページ10に含まれる内容の要旨
1. Safety 6 R5976470 D320PL DIGITIZER 13122002
ページ11に含まれる内容の要旨
2. Introduction 2. INTRODUCTION 2.1 General functionality Overview The D320PL is a video processing device, designed to drive as well Barco LED walls as large screen projectors, monitors, plasma screens, ... etc. The D320PL is capable of handling all standard output formats like SVGA, XGA, SXGA and UXGA on an analog RGBHV and digital DVI output. The D320PL Digitizer allows you to control up to 4sources onone display. Seamless switch from source to source or display sources together, overlay them
ページ12に含まれる内容の要旨
2. Introduction Type Value Compatibility Barco Daylight / ILite Displays and large screen projectors, monitors, plasma screens... Output DVI-A, DVI-D, Barco LED protocol Scalability Chaining for more inputs, stacking for more displays Flexibility User defined input Scaler 4inputchannels[Data-Video]fullyindependentscalabletodesired output resolution Z-order control Instant modification of Z-order control, for each output window Window Positioning Intuitive positioning interface Connectors RS 232
ページ13に含まれる内容の要旨
2. Introduction 2.4 Dimensions of the D320PL Digitizer Dimensions Image 2-2 R5976470 D320PL DIGITIZER 13122002 9
ページ14に含まれる内容の要旨
2. Introduction 10 R5976470 D320PL DIGITIZER 13122002
ページ15に含まれる内容の要旨
3. Physical Installation of the D320PL Digitizer 3. PHYSICAL INSTALLATION OF THE D320PL DIGITIZER 3.1 Installation requirements Requirements The D320PL Digitizer should not be placed in a built-in installation or enclosure unless proper venti- lation is provided. Whenusingtheunitinamulti-unitrackassemblyorclosedassembly,theambienttemperatureinside the assembly may not exceed the maximum rated ambient temperature of the Digitizer. The instal- lation should be such that the amount of air flow
ページ16に含まれる内容の要旨
3. Physical Installation of the D320PL Digitizer 3.2 Connections Rear panel inputs/outputs Image 3-2 A LED-WALL / PROJECTOR OUTPUT BPowerSwitch C Power input DLOOPIN ELOOPOUT F Retractable dust filter G COM1 : RS232 input H COM2 : RS232 chaining output I COM3 : RS232 stacking output J TCP-IP : Ethernet LAN connector 12 R5976470 D320PL DIGITIZER 13122002
ページ17に含まれる内容の要旨
3. Physical Installation of the D320PL Digitizer A : LED-WALL / PROJECTOR OUTPUT (DVI output connector with 3 functions) - LED wall out (Barco proprietary protocol). - RGB HV out (analog). - DVI digital out. (DVI compliant, eg: monitor, projector, plasma, ... ) B : Power switch - The power ON/OFF switch is provide on the rear side of the Digitizer. o Switchpressedto1=theunitstarts. o Switch pressed to 0 = unit totally switched off. C : Power input - Autoranging from 90 to 260 VAC / 130 Wat
ページ18に含まれる内容の要旨
3. Physical Installation of the D320PL Digitizer Image 3-3 How to insert an input module into the D320PL Digitizer 1. Gently slide in the input module into a free input slot with the grip handle at the top. 2. LockinginthemodulebypushingtheinputmodulecompletelyintotheD320PLDigitizeruntiladefinite click is audible. Maximum two HDSDI input modules may be inserted in one D320PL Digitizer. 14 R5976470 D320PL DIGITIZER 13122002
ページ19に含まれる内容の要旨
4. Input modules 4. INPUT MODULES Overview DVI input module SDI input module HDSDI input module CVBS / S-VID input module YUV / RG(s)B input module RGB analog input module Dummy input module 4.1 DVI input module Technical info: Computer generated graphical source. DVIdatain. 162 MHz pixel clock. Resolution from VGA to UXGA/60 Hz. DVI compliant. DVI loop through. Amber LED (upper LED on the front side) will be lit indicating module start up. When placed in an input sl
ページ20に含まれる内容の要旨
4. Input modules 4.2 SDI input module Technical info: SDIdatain. SDI loop through. 270Mbit/s transmission (SMPTE 259M-C). 525/625 interlaced. Coax(75Ohm). Amber LED (upper LED on the front side) will be lit indicating recognition of film, either continuous or intermittent film detection. When placed in an input slot the green LED (lowerLED on the front side)will be lit indicating that the system acknowledges the module. Image 4-3 Image 4-4 Order info: Article No. Description R9850970
