ページ1に含まれる内容の要旨
Model APS-596C
Owner’s Manual
5 Button Remote Security System
with Dual Stage Shock Sensor
IMPORTANT! In order to provide the highest possible level of security to your vehicle, this
system is equipped with selectable manual override circuitry. It is possible that you will need
to manually override your security system if the transmitter becomes lost, or inoperative due
to battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is
necessary to fully understand the procedure
ページ2に含まれる内容の要旨
YOUR “ Code Hopping “ TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter, and retransmit at a later time to disarm your system. Your anti code hopping transmitters will change their signal every time the but
ページ3に含まれる内容の要旨
dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. Closing the hood, trunk, or doors will correct the problem and you do not need to disarm the system to make the correc- tion. Doors Lock - Optional Headlight Illumination - Optional ARMING THE SYSTEM - PASSIVE ( AUTOMATIC ) 1. Turn off the engine, exit the vehicle and close and lock all doors, hood lid and trunk lid. Dash mounted LED begins to flash rapidly, indicating
ページ4に含まれる内容の要旨
DISARMING THE SYSTEM As you approach the vehicle, press and release the Unlock button on the keychain Transmitter. Dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is re-arming auto- matically. Open any door to suspend the automatic arming. Parking Lights flash two times. If the parking lights flashed three times, then the alarm was trig- gered in your absence. Before turning the key on,
ページ5に含まれる内容の要旨
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. If your transmitter has a separate lock/unlock buttons, pressing the unlock button anytime after the first unlock command will cause all the vehicle doors to unlock. Headlight Illumination - Optional WHILE THE SYSTEM IS SOUNDING If during a triggered state, you wish to shut off
ページ6に含まれる内容の要旨
MANUALLY OVERRIDING YOUR SYSTEM: Using The Receivers Push-Button Override Switch Your Security System can be disarmed without the use of the keychain transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. If your system has been selected for Valet Switch manual override as indicated on the last page of this manual, to bypass the alarm system; 1. Open the vehicle door. The alarm will sound. 2. Turn the ignition
ページ7に含まれる内容の要旨
5. Within 10 seconds, begin to press and release the Receivers Push-button switch to set the tenths digit. (As per the example, press and release 5 times to set the tenths digit to 5) 6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off then on. 7. Within 10 seconds, begin to press and release the Receivers Push-button switch to set the units digit. (As per the example, press and release 2 times to set the units digit to 2). 8. Turn the ignition switch to the of
ページ8に含まれる内容の要旨
2. To stop the alarm, press and hold the ARM or DISARM button on the transmitter again for 3 seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds. Also if any transmitter button other than the ARM or DISARM button is pressed and released, the Panic mode will be turned off immediately. The normal function of this transmitter button will be suspended during the Panic sounding period. 3. While in the Panic mode, pressing and releasing the ARM or DISARM buttons
ページ9に含まれる内容の要旨
IGNITION CONTROLLED LOCK UNLOCK: (Unlock Drivers Only, or Unlock All Doors) Your security system has a selectable safety feature that allows the vehicle doors to lock when the ignition switch is turned on, (Providing all doors are closed), and to unlock the doors when the ignition switch is turned off. In addition, the unlocking of the doors is further selectable, in a two step unlock configuration, to unlock only the drivers door or all doors. TELEMATIC UPGRADE: This system has the ability to
ページ10に含まれる内容の要旨
Included with your system is a two way remote transceiver that makes use of a LCD screen to ensure that the vehicle reacted to commands that you executed from the hand held transmitter(s). These screens are shown below for your reference. When Disarmed, Press the Arm/Lock button to Lock and Arm the System. The Lock Icon is displayed on the LCD panel and the park- ing lights flash once. When Armed, Press the Disarm/Unlock but- ton to Unlock and Disarm the System. The Unlock Icon is displayed o
ページ11に含まれる内容の要旨
If the alarm system has been triggered, the icon displayed on the transmitter LCD will in- dicate which zone has been activated, as well sound the beep tones, or vibrate dependent upon the setting as shown above. The fol- lowing trigger patterns will be displayed. Triggered and the entry attempt was made to one of the vehicle doors. Triggered and entry attempt was made to the vehicles hood or trunk. Triggered and entry attempt was made to the vehicles glass, or the vehicle has been hit or bump
ページ12に含まれる内容の要旨
When the vehicle is armed and the vibration sensor input is active, the transmitter will chirp 3 times, the lights will flash and then the dis- play will flash as shown. When the input or the zone clears, the transmitter will chirp 1 time and the display will clear. The Battery Icon Indicator will show 3 bars as shown left, when the battery is at full capacity and will show less than 3 bars as the battery discharges. This is a guide and should be used to monitor the condition of the battery.
ページ13に含まれる内容の要旨
Parking Meter Counter: The transmitter has a built in clock that can count down from 10, 20, 30, 60, 90, or 120 minutes. This feature is useful when parking the vehicle in a metered parking lot. If the time on the parking meter is 30 minutes, you can set the count down timer to 20 minutes. The transmitter will emit a beep tone when the timer expires to remind you to get back to your vehicle. See following chart for setting the parking meter count down timer feature. Alarm Clock Mode: The tran
ページ14に含まれる内容の要旨
14 128-8803 14 of 16
ページ15に含まれる内容の要旨
APS-596C SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN CHIRP INDICATORS *1 CHIRP = ARM *2 CHIRPS = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de-activated. PARKING LAMP INDICATORS 1 FLASH = ARM 2 FLASHES = DISARM 3 FLASHES = DISAR
ページ16に含まれる内容の要旨
© 2010 Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-8803 16 128-8803 16 of 16
