ページ1に含まれる内容の要旨
Installation Installation Guide
Wireless Audio / Video Kit
GUWAVKIT
1
ページ2に含まれる内容の要旨
2 3
ページ3に含まれる内容の要旨
Table of Contents System Requirements 4 Video Mode Configuration 45 Important Information 5 Screen Resolution Configuration 48 Package Contents 6 Wireless USB Transmitter Settings 51 Device Overview 8 Wireless USB Transmitter Selection 53 Wireless USB Transmitter 8 Wireless USB Transmitter Reset 54 Wireless VGA Receiver 9 Wireless VGA Receiver in Wired Mode 55 Wireless Audio Receiver 11 Trouble Shooting Guide 56 Preparing for Setup 12 Technical Specifications 70 Software Installation 17 Appendix
ページ4に含まれる内容の要旨
System Requirements • Microsoft Windows® XP (SP2) or Vista (32- / 64-bit) with available USB 2.0 port • 1.6 GHz processor (CPU) with 1GB of system memory (RAM) • Flat-panel (LCD / Plasma / DLP) TV display or Projector with VGA (RGB / D-sub 15-pin / PC) or DVI port (Does NOT work with CRT tube TV) • TV or audio system with 3.5mm audio jack or RCA connectors Suggested system requirement to play online video clips in a “window” – 1.6 Ghz Atom™ with 1GB RAM, 480p video in a “window” – 1.8 Ghz Pen
ページ5に含まれる内容の要旨
Important Information Before you get started, please NOTE: Do not place Wireless USB devices under direct sunlight or near high heat emitting devices; Do not place Wireless USB devices near water or wet surfaces to avoid electric hazards; Do not place Wireless USB devices on any moving or unstable surfaces. 4 5
ページ6に含まれる内容の要旨
Package Contents • 1 x Wireless VGA • 1 x USB 2.0 A to mini-B cable (3 ft.) receiver (for display) • 1 x USB 2.0 extension cable (4 ft.) • 1 x Wireless Audio receiver (for stereo) • 1 x Gold Plated VGA cable (6 ft.) • 1 x Wireless USB Transmitter (for computer) • 1 x 3.5mm to 3.5mm cable • 1 x VGA (F) to DVI-A adapter 6 7 LINK PWR
ページ7に含まれる内容の要旨
• 1 x 3.5mm to RCA cable • 1 x Hook-and-loop fastener • 1 x Quick Start Guide / User manual • 1 x Power adapter for Audio Receiver • 1 x Installation CD • 1 x Power adapter for Video Receiver • 1 x Warranty / Registration Card 6 7
ページ8に含まれる内容の要旨
Device Overview Wireless USB Transmitter 1. LINK: Data Transfer Activity Indicator - LED blinks when data is being transferred 2. PWR: Power 1 2 - LED is solid when powered by the PC 3. USB Connector - Connect to any available USB 2.0 port on your computer 3 8 9 LINK PWR
ページ9に含まれる内容の要旨
Wireless VGA Receiver 1 2 3 4 5 6 7 8 9 8 9
ページ10に含まれる内容の要旨
1. VGA : VGA Activity Indicator 5. Power Plug - LED is solid when display cable is connected - Power adapter socket - LED is blinking when data is being transferred 6. RESET Button 2. PWR: Power Indicator - Association history can be erased by pressing and holding this button for 10 seconds. (Please visit P.54 - LED is solid when power is applied for details) 3. Status Indicator 7. HOST Button - Single* solid light: device is wirelessly connected to the selected Wireless USB Transmitter - T
ページ11に含まれる内容の要旨
Wireless Audio Receiver 1. Power/Activity LED - LED is solid when connection is established - LED is blinking when power is on and connection is not established 2. 3.5mm Audio Socket 1 - Connects to the 3.5mm audio connector of the included 3.5mm or RCA audio cable, and the other end to the available 3.5mm audio socket or RCA audio socket on your display or stereo system 3. Mini-B USB Port - Connects to the mini-B end of the included USB cable, and the Type-A end to an available USB port
ページ12に含まれる内容の要旨
Preparing for Setup Before you begin, please make sure to properly remove all previously installed Wireless USB Manager and DisplayLink drivers from your system to avoid driver conflict. To properly remove previously installed drivers, please follow below instructions. For Windows XP users 1. Go to Start -> Control Panel -> Add or Remove Programs 2. Select any previously installed DisplayLink software and click on Remove button to properly uninstall the program. 3. After all DisplayLink
ページ13に含まれる内容の要旨
4. Repeat steps 1 and select any previously installed Wireless USB drivers and click on Remove button to properly uninstall the program. 12 13
ページ14に含まれる内容の要旨
For Windows Vista users 1. Click on the Vista logo. Click on Control Panel then double click on Programs and Features. 2. Select any previously installed Displaylink software and click on Uninstall button to properly uninstall the program. 14 15
ページ15に含まれる内容の要旨
3. After successfully remove the DisplayLink software, please restart your system. 4. Repeat Step 1 and select IOGEAR Wireless USB to VGA Kit and click on Uninstall. 14 15
ページ16に含まれる内容の要旨
After all previously installed DisplayLink and Wireless USB to VGA Kit software are properly removed, please make sure to install the software on the CD following the procedures on the next page before plugging in the Wireless USB Transmitter to your computer. Important Note: If installing on Windows XP, Service Pack 2 (SP2) is required. Please verify that this has been installed before installing the Wireless Audio/Video Kit software. Before installing the software, please make sure t
ページ17に含まれる内容の要旨
Software Installation – Windows XP For Windows XP users Important Note: For Windows XP users, if you do not have Mi- 1. Insert the installation CD into the CD-ROM on crosoft .NET Framework 2.0 installed, you will be your computer and the InstallShield Wizard will load automatically. prompted to have it installed. Please follow below instructions for installation. 1. Click “Yes” to install .NET 2.0 Framework 2. Check “License Agreement” and click “Install” 3. Click “Finish” to complete th
ページ18に含まれる内容の要旨
2. Click on “Next” to continue. 3. Click on “Yes” to accept the software License Agreement and continue the installation. Note – If you previously installed IOGEAR Wireless USB Hub and Adapter Kit (GUWH104KIT) software, please follow detail instructions on P.72 Appendix. 18 19
ページ19に含まれる内容の要旨
4. The InstallShield Wizard will continue loading 5. The installation wizard will continue to install the the drivers. Do not click on any button, other- video driver provided by DisplayLink. Click on wise, it will interrupt the installation process and “I Accept” to continue the installation. cause malfunction of the product. Note – If this screen does not appear, please make sure you correctly remove all DispalyLink software from your system. After un-installation, please repeat the
ページ20に含まれる内容の要旨
6. The DisplayLink driver starts to load. Do not 7. Click on “Finish” to complete the software installation. click on any button, otherwise, it will interrupt the installation process and cause malfunction of the product. It is highly recommended to restart your system after the software installation to ensure all drivers are loaded correctly. 20 21
