ページ1に含まれる内容の要旨
SHARP
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read
this manual carefully. It will guide you in operating your SHARP product.
• HT-SL72 SOUND BAR HOME THEATER SYSTEM consisting of TX-SL72 (Amplifier System),
CP-SW72 (Active Subwoofer System) and HT-SL72 (Sound Bar).
• HT-SL77 SOUND BAR HOME THEATER SYSTEM consisting of TX-SL77 (Amplifier System),
CP-SW77 (Active Subwoofer System) and HT-SL77 (Sound Bar).
HT-SL72 HT-SL77
H roll TM
NaGH
ページ2に含まれる内容の要旨
The following accessories are included, This )roduct has noremote control, HT-SL77 only Subwoofer Stand x 2 Audio Cable x 1 HDMI Cable x 1 Wall Mount RCA to Headphone Bracket x 2 Cable (1pin - 2 pins) x 1 (GITAUA004AW01) (QCNWGA080AWPZ) (QCNWGA077AWPZ) (QCNWGA081 AWPZ) (LHLDZA267AWSA) Wall Mount Sound Bar Stand Pattern Paper (Sound Bar) Amplifier Stand x 2 Speaker Wire x2 Angle x 2 (TCAUHA030AWZZ) (GITAUA021AW01) (QCNWHA046AW01) (LANGKA225AW01) (GITAUA012AW01) Screw for Brackets Sound Bar Stand
ページ3に含まれる内容の要旨
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 CAUTION _lk of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, CAUTION: TO REDUCE THE RISK OF ELECTRIC and can radiate radio frequency energy and, if not installed SHOCK, DO NOT REMOVE COVER (OR BACK). and used in accordance with the instructions, may cause NO
ページ4に含まれる内容の要旨
Electricity is used to perform many useful functions, but it 17) Object and Liquid Entry - Never push objects of any kind can also cause personal injuries and property damage if into this product through openings as they may touch improperly handled. This product has been engineered dangerous voltage points or short-out parts that could result in a fire or electric shock. and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or To prevent fi
ページ5に含まれる内容の要旨
CONSUMER LiMiTED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below. This warranty does not app
ページ6に含まれる内容の要旨
FRONT VIEW t 2 3 4 • Donot expose the unit tomoisture, totemperatures higher than 140°F (60°C) orto extremely low temperatures. • Ifyour system does not work properly, disconnect the AC power cord from the AC outlet and replug. • Incase ofan electrical storm, unplug the unit for safety. • Hold the AC power plug by the head when removing it Reference page from the AC outlet, aspulling the cord can damage 1. Gain (AUDIO IN) Knob ...................... 13 internal wires. 2. Pairing Button .........
ページ7に含まれる内容の要旨
FRONT VIEW 1 2 REAR VIEW Reference page 1. Left Front Speaker 4. Right Front Speaker Terminal (Red/Black) .... 10 2. Right Front Speaker 5. Left Front Speaker Terminal (White/Black) .... 10 3. Bass Reflex Duct FRONT VIEW REAR VIEW --3 Reference page Reference page 4. Bass Level switch ........................ 13 1. Power/Pairing Indicator .................... 13 2. Bass Reflect Duct 5. Pairing button ........................... 13 3. Woofer 6. AC Power Cord ........................... 10
ページ8に含まれる内容の要旨
1 To fix the Sound Bar stand 1. Peel off the double sided tape separator and attach the Make sure to unplug the AC power cord before I installing the unit or changing the position. 1 Sound Bar stand cushion at the bottom surface of the Sound Bar stand. Select from three installation methods according to the preferred position. Sound Bar stand cushion Sound Bar Double For 52" 60" or 70" TV Sound Bar assembly stand sided tape Use Sound Bar cover joint 7-13/32" separator (188 mm) for 52" TV. Hook F
ページ9に含まれる内容の要旨
Caution: 3.Slot inthe Sound Bar tothe base stand according to your TV size. • Be very careful to prevent the Sound Bar and Amplifier from falling when mounting on the wall. • Before mounting, check the wall strength. (Do not put on the veneer plaster or whitewashed wall. The Sound Bar may fall.) If unsure, consult a qualified service technician. 60" TV{_ • Mounting screws are not supplied. Use appropriate ones. _ _J} 70 II TV • Check all wall mount angle screws for looseness. • Select a good loc
ページ10に含まれる内容の要旨
The Amplifier can be installed as below: 4 Screw the wall mount angle to the wall as shown in the illustration. (Total screw is 4 pieces) 1 2 3 • Make sure that the screw and the wall can support a load of 45 Ibs (20 kg). Wall mount angle "_ ..... E. Wall Horizontal Vertical On the wall ws x 2) / ' "_ mount To mount the Amplifier on the wall, perform the following /- ,,,,/ ang e steps. Wall surface ( _ ....... (screws x 2) X_ 1 Make a hole on the wall using a drill. 5 Align the wall mount slot a
ページ11に含まれる内容の要旨
Installation image: Notes: l As the sound from the system is omni-directional, you can place the speaker anywhere you like. However, it is TV recommended to place it as close to the TV as possible. • The front panel of the speaker is not removable. • If the Amplifier is wall mounted behind the TV, make sure the distance between the TV and Amplifier are not less than 8" (20cm) to avoid wireless interruption. Caution: Do not change the installation direction when the unit is turned on. Place the s
ページ12に含まれる内容の要旨
Caution: • Turn off all other equipment before making this connection. Notes: • Setthe TV at lowvolume beforeturningon thesystem. • GAINknob isinvalidduring DIGITAL(HDMI)function. • Makesureto set the correctinputselectoron theAmplifierto a preferred connectionbefore usingany of these methods. Amplifier ACTIVE CONNECTION INPUT SELECTOR HDMI Set to DIGITAL HEADPHONE OUT Set to ANALOG RCA • This unit supports HDMI which enables ARC (AudioReturn Channel). • To enable ARC make sure to use High Speed
ページ13に含まれる内容の要旨
Switch the input selector toANALOG. (For HT-SL77) Connect tothe TV using an audio cable. 1.Method 1 TV l ToHEAOPHONEtermna -- Audio cable Amplifier Notes: • Connecting via this method may disable TV internal speakers. • In some cases, a small background noise could emit from the Sound Bar, when you use the headphone connection with a TV-Set. In such case, please change the connection to the HDMI/ARC or RCA-connection. This effect depends on the used TV-Brand, model and age, and it is not a quali
ページ14に含まれる内容の要旨
] I of Make the sure TV. (HT-SL77) to enable the HDMI CEC when making HDMI connection. For details, refer to the operation manual I 1 Notes: • If a device such as microwave oven, wireless LAN card, Bluetooth device or any other device that uses the Plug the AC power cord into a AC outlet, the stand-by indicator turns RED. same 2.4GHz frequency near the system, some sound interruption may be heard due to interference. The Amplifier will automatically power on if: DIGITAL (HDMI) function: TV or si
ページ15に含まれる内容の要旨
Many potential problems can be resolved by the owner Possible cause Symptom without calling a service technician. • Wireless connection • Checkthe distance If something is wrong with this product, check the following cannot be before calling your authorized SHARP dealer or service between the Amplifier and center. established. Subwoofer (less than 32 feet (10m)). • Make sure there is no other wireless devices near the unit. Possible cause Symptom • Make sure there is no • No sound is heard • Is
ページ16に含まれる内容の要旨
Aspart ofour policy ofcontinuous improvement, SHARP reserves theright tomake design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal Type FullRangespeakersystem values ofproduction unit. There maybe some deviations 14/16"x 4-1/2 (2.2x 11.5cm) from these values inindividual unit. FullRange Maximum input 100W/OH power Ratedinputpower 50W/CH Powersource AC120V _ 60Hz Impedance 3ohms/CH(4piecesparallel) Power 20W cons