ページ1に含まれる内容の要旨
18V Cordless 1/2”
ImpaCt WrenCh
model 67845
set up and operatIng InstruCtIons
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sa Ve thIs manual.
© ®
Copyright 2010 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual
ページ2に含まれる内容の要旨
Contents Important saFetY InFormatIon .................................3 general poWer t ool saFetY WarnIngs ........................................... 3 ImpaCt WrenCh saFetY WarnIngs ........................................... 5 VIbratIon saFetY .............................. 6 groundIng ......................................7 double Insulated t ools: t ools WIth tWo prong plugs ... 7 extensIon Cords .............................. 7 sYmbologY .......................................... 7 sp
ページ3に含まれる内容の要旨
notICe is used to sa Ve thIs manual address practices not Keep this manual for the safety warnings related to personal injury. and precautions, assembly, operating, CautIon, without the inspection, maintenance and cleaning safety alert symbol, is procedures. Write the product’s serial number used to address practices not in the back of the manual near the assembly related to personal injury. diagram (or month and year of purchase if product has no number). Keep this manual general
ページ4に含まれる内容の要旨
operating a power tool. do not use safety equipment may not provide a power tool while you are tired or adequate protection. Eye protection under the influence of drugs, alcohol must be ANSI-approved and breathing or medication. A moment of inattention protection must be NIOSH-approved for while operating power tools may result the specific hazards in the work area. in serious personal injury. 4. power tool use and care b. use personal protective equipment. a. do not force the power too
ページ5に含まれる内容の要旨
the power tool for operations different 2. Avoid unintentional starting. Prepare to from those intended could result in a begin work before turning on the tool. hazardous situation. 3. Do not lay the tool down until it has come 5. battery tool use and care to a complete stop. Moving parts can grab the surface and pull the tool out of a. recharge only with the charger your control. specified by the manufacturer. A charger that is suitable for one type of 4. When using a handheld power to
ページ6に含まれる内容の要旨
electrical shock. Vibration safety • Any power cord must be properly This tool vibrates during use. Repeated grounded. Ground Fault Circuit or long-term exposure to vibration may Interrupter (GFCI) should also be cause temporary or permanent physical implemented – it prevents sustained injury, particularly to the hands, arms electrical shock. and shoulders. To reduce the risk of 8. WARNING: Some dust created by power vibration-related injury: sanding, sawing, grinding, drilling, an
ページ7に含まれる内容の要旨
Standard Association, and the National sa Ve these Electrical Code. InstruCtIons. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the groundIng preceding illustration. (see outlets for 2-prong plug.) t o preVent eleCtrIC shoCk extension Cords and death From InCorreCt groundIng WIre note: Extension cords must not be used with ConneCtIon: this item’s charger. Check with a qualified electrician if you are in doubt as to whether the outlet is properl
ページ8に含まれる内容の要旨
Functions speCIFICatIons Housing, right & left Battery Pack 18 V / NiCd / 1700 mAh (24 & 28) Impact Anvil (6) Speed 0 - 2,100 RPM / 3,000 BPM (No Load) Average 205 ft-lbs Forward (clockwise) Torque 211 ft-lbs Reverse (counterclockwise) Drive 1/2” Square Drive Bolt Capacity 1/2” (13 mm) Forward/Reverse Lever (26) unpaCkIng Trigger (27) Handle When unpacking, make sure that the Battery Pack (35) item is intact and undamaged. If any parts are missing or broken, please call Harbor Battery Pack
ページ9に含まれる内容の要旨
4. Charge for 2-1/2 to 3 hours, then unplug Charging the battery pack the Adapter from the wall and the Adapter (37) Charger (36) Charger, and remove the Charger from the Battery Pack. 5. Allow the components to cool if they are warm or hot to the touch. Store the Adapter and Charger in the Storage LED Light Flanges Case (38). CautIon: Do not leave the Battery Pack Figure 2 charging for more than 5 hours or the Battery Pack may become damaged. 1. Plug the Adapter (37) into a 120V wall
ページ10に含まれる内容の要旨
• To set the Impact Anvil (6) to turn 5. Set the desired direction of the Impact forward (clockwise), press the right Anvil (6) with the Forward/Reverse Lever side of the Forward/Reverse Lever (26) (26). until it clicks into place. 6. Position the socket over the fastener. • To set the Impact Anvil (6) to turn in 7. Holding the handle firmly with one hand Reverse (counterclockwise), press the and the top of the Housing (24 & 28) left side of the Forward/Reverse Lever with your other hand,
ページ11に含まれる内容の要旨
Cleaning, maintenance, and maIntenanCe and lubrication ser VICIng 1. beFore eaCh use, inspect the Procedures not specifically general condition of the tool. Check for explained in this manual must loose hardware, misalignment or binding be performed only by a qualified of moving parts, cracked or broken parts, technician. damaged electrical wiring, and any t o preVent other condition that may affect its safe serIous Injur Y operation. From aCCIdental 2. aFter use, wipe external
ページ12に含まれる内容の要旨
please read the FolloWIng CareFull Y THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROvIDED THE PARTS LIST AND ASSEMBLy DIAgRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAkES ANy REPRESENTATION OR WARRANTy OF ANy kIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAkE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACE
ページ13に含まれる内容の要旨
assembl Y dIagram 36 37 35 SKU 67845 For technical questions, please call 1-800-444-3353. Page 13
ページ14に含まれる内容の要旨
lImIted 90 da Y WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installati
