ページ1に含まれる内容の要旨
12 VOLT IMPACT WRENCH
Model 92349
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical
ページ2に含まれる内容の要旨
Specifications Maximum Torque 150 Ft. Lbs. 1 Drive Size / ” Square 2 Blows Per Minute 30 to 40 Power Cord (12 Volt Plug In) 18 AWG X 2C SPT - 2, 11’ Long 7 13 3 11 Accessories / ”, / ”, / ”, & / ” Sockets 8 16 4 16 NOTE: Unlike air-operated or 120V AC impact wrenches, this Wrench will build up inertia before striking a blow. This is normal, and DOES NOT INDICATE A PROBLEM. Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and mai
ページ3に含まれる内容の要旨
9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician. The handle must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect power. Unplug tool when not in use. 11. Avoid unintentional starting. Be sure the Trigger is in the Off position when not in use and before plugging in. Do not carry
ページ4に含まれる内容の要旨
Unpacking When unpacking, check to make sure the parts listed on page 7 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Operation WARNING! Running engines produce carbon monoxide, an odorless, colorless gas that is extremely toxic. Exposure to carbon monoxide can result in headaches, dizziness, vomiting, and even death. The engine must only be run in an open, well-ventilated place. 1. Prior to us
ページ5に含まれる内容の要旨
Operation (continued) WARNING: Working around vehicle engines whether running or not is inherently dangerous, and extraordinary precautions outside the scope of this booklet are required. Refer to the owner’s manual of your vehicle for more information. 4. NOTE: Unlike air-operated or 120V AC impact wrenches, this wrench will build up inertia before striking a blow. This is normal, and DOES NOT INDICATE A PROBLEM. 5. Make sure the vehicle is parked safely away from all other moving traffic. Be s
ページ6に含まれる内容の要旨
Operation (continued) 9. Occasionally, you will have to manually break a nut loose before you can remove it with the Impact Wrench. To do so, use a Breaker Bar (not included) and Socket to break the nut loose. Then, proceed as discussed in number 8 on page 5. 10. Replace the wheel on the vehicle hub, aligning the wheel studs with the bolt holes in the wheel. 11. Install the wheel lug nuts, following the vehicle manufacturer’s recommendations. To avoid cross-threading the lug nuts, thread the nu
ページ7に含まれる内容の要旨
Parts List Part No. Description Part No. Description 1 Bearing 21 Bolt 2 Anvil Bearing 22 Cable Block 3 Radial Bearing 23 Cable Bushing 4 Anvil 24 12V Plug-In 5 Oil Bearing 25 Left Housing 6 Rachet Wheel Base 26 Trigger 7 Wheel 27 LED 8 Wheel Tray 28 Bolt 9 Pull Spring 29 Wheel 10 Wheel Brace 30 Pull Spring 11 Rachet Wheel Bearing 31 Bolt 12 Pedestal Bearing 32 Bolt 13 Gear 33 Pawl 14 Gear Shaft 34 Rod 15 Drive Wheel 35 7/8” Socket 16 Motor Gear Wheel 36 13/16” So
ページ8に含まれる内容の要旨
Assembly Drawing 23 19 24 22 18 17 20 16 21 14 13 15 12 11 9 10 7 8 25 6 28 29 26 30 5 4 38 27 31 32 37 33 3 34 36 2 1 35 39 Note: The Battery Adapter Cable (40) is not shown. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 92349 For technical questions, please call 1-800-444-3353 Page 8
