ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS
Multiple Projector Stacking System - Table Stand
LCD2TS
ページ2に含まれる内容の要旨
LCD2TS Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and CSAV, Inc., and its affiliated corporations and subsidiaries follow all instructions can result in serious personal injury, (collectively, "CSAV"), intend to make this manual accurate and damage to equipment, or voiding of factory warranty! It is the complete. However, CSAV makes no claim that the information installer’s responsibility to make sure all components are contained herein covers all deta
ページ3に含まれる内容の要旨
Installation Instructions LCD2TS LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaien
ページ4に含まれる内容の要旨
LCD2TS Installation Instructions TOOLS REQUIRED FOR INSTALLATION 7/32" (5.5mm) #2 1/2" (12.7mm) PARTS C (1) A (2) B (1) D (4) E(1) F (1) G (8) I (5) J (8) H (8) K (8) L (16) M (8) 1/4-20 x 1-1/2" 5/16-18X3/8" 1/4-20X1-1/4" 1/4-20X1-1/2" 4
ページ5に含まれる内容の要旨
Installation Instructions LCD2TS Assembly And Installation For RPA Models Only 6 (F) WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment. It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. (C) Reinforce the structure as required before installing the component. 1. Set the base plate (B) on a flat stable
ページ6に含まれる内容の要旨
LCD2TS Installation Instructions 6. Insert four 1/4"-20x1-1/4" (J) button head cap screws from the top of the projector arm. (See Figure 4) (A) (J)x4 8 (L)x4 RPM not shown for clarity only Figure 4 7. Place a 1/4" flat washer (L) onto each screw. 8. Hold the RPM (with interface brackets attached) to the bottom of the projector arm and tighten the screws through the washers and into the interface brackets. 9. Proceed with Steps 5 - 10 from For RPA Models Only section 6
ページ7に含まれる内容の要旨
Installation Instructions LCD2TS 7
ページ8に含まれる内容の要旨
LCD2TS Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Room 30I, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112 8804-000053 RevA 2006 Chief Manufacturing www.chiefmfg.com P +86-755-8996 9226 ; 8996 9236 ; 8996 9220 11/06 F +86-755-89
