ページ1に含まれる内容の要旨
Programming Menu
ページ2に含まれる内容の要旨
NOTES SCANTEAM 2380 Programming Menu Please Note: The programming features on each menu page are not supported in all models and software revisions of the SCANTEAM 2380. Notations are included if the feature is available only in certain models. Contact your Welch Allyn Sales Coordinator for the revision/model to fit your needs. The SAMPLE BAR CODES page (near the end of the programming menu) contains bar code symbols that you may use to verify that you have programmed your SCANTEAM 2380 correc
ページ3に含まれる内容の要旨
STATUS SCANTEAM 2380/PM Programming Menu CHECK SHOW FIRMWARE REVISION LEVEL Scan the bar code below to display the revision level of the SCANTEAM 2380 firmware. For example: After scanning the Firmware Revision Level bar code, “(C) WA93C” is output to the terminal/host device. The “C” at the end indicates the firmware is at revision level C. Firmware Revision Level SHOW SOFTWARE NUMBER Scan the bar code below to display the SCANTEAM 2380 software number. The resulting information will show i
ページ4に含まれる内容の要旨
USER’S SCANTEAM 2380 Programming Menu NOTES 4
ページ5に含まれる内容の要旨
SYSTEM SCANTEAM 2380/PM Programming Menu GUIDE USE THIS PAGE As a general overview of the programming menu. The programming menu consists of two basic components as shown below. Programming Menu BAR CODE CHART CODE Programming Menu USE THIS PAGE SELECTION II In combination with the adjoining menu pages to program the unit. (RETAIL) The bar codes on this page correspond to symbols in shaded areas on adjoining menu pages. SCAN these bar codes in the sequence indicated on menu page to program desir
ページ6に含まれる内容の要旨
SCANTEAM 2380 Information and Examples TERMINAL SELECTION DIRECT CONNECT ENABLE When enabled, this programming selection allows the wand scanner to replace the keyboard. The scanner will respond the the PC keyboard initialization commands upon power up. This selection is for an AT keyboard only with a terminal ID of 03. LOW POWER When enabled, this programming selection puts the wand scanner in a low power mode. The LED will be pulsed to conserve power and will “wake up” when a transition from
ページ7に含まれる内容の要旨
TERMINAL SCANTEAM 2380 Programming Menu SELECTION USE THIS PAGE To select the terminal type. To enable the AT Direct Connect feature. To enable the Low Power feature. scan scan terminal selection scan PC/XT IBM 01 ENTER PS/2 model 30 02 PC/AT, PS/2 50–80 03 PS/2 30–286 3196/97, 3476/77 07 3191/92, 3471/72 (102 Keyboards) 3196/97, 3476/77 08 (122 Keyboards) 3191/92, 3471/72 09 (122 Keyboards) M19, M24, M28 OLIVETTI 01 M200, M240, M250, M290, 03 M380, P500 078/079/080/191 TELEX 09 VT220, 320, 34
ページ8に含まれる内容の要旨
SCANTEAM 2380 Information and Examples OUTPUT PARAMETERS & FORMAT SELECTIONS PREAMBLE/POSTAMBLE Preambles and Postambles are characters added by the 2380 to scanned bar code data. These characters are sent with the bar code data to the terminal. Use the Hex–ASCII table below to find the alpha–numeric code to be used for programming a particular Preamble or Postamble. NOTE: The 2380 will translate characters 00–1F (keyboard function codes) into keyboard “function keys.” The assigned translation
ページ9に含まれる内容の要旨
OUTPUT PARAMETERS SCANTEAM 2380 Programming Menu & FORMAT SELECTION USE THIS PAGE To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To add preambles and/or postambles to the bar code. To select function transmit enable. To select keyboard type. To set intercharacter, interfunction, and intermessage delays to specific values. To control scanning indicators or enable function records feature. scan To enable the Append Buffer when Code 3 of 9 with append option is enabl
ページ10に含まれる内容の要旨
SCANTEAM 2380 Information and Examples COMM 1 INTERNATIONAL KEYBOARDS The unit aligns the keyboard layout based on the International Keyboard selected here. INTERMEC COMPATIBILITY YES – Allows the unit to be compatible with Intermec keyboard function codes. NO – The default keyboard function codes that are in the preamble and postamble remain active at all times. 10
ページ11に含まれる内容の要旨
SCANTEAM 2380 Programming Menu COMM 1 USE THIS PAGE To select foreign keyboards. To enable Intermec compatibility scan selections scan variables scan scan France A INTERNATIONAL ENTER KEYBOARDS (3) Germany B Spain C scan Switzerland D Italy E USA F* Sweden (4) G DEFAULT Canada (5) H Portugal (5) I Yes/No* INTERMEC COMPATIBILITY (3) scan Notes: (1) * Designates DEFAULT selections. (2) See facing page for more information and examples. (3) This programming feature is supported for Mask B and
ページ12に含まれる内容の要旨
SCANTEAM 2380 Information and Examples SCANCODE SELECTION K2 SCANCODE CAPABILITY Reconfigures the 2380 to use K2 (SCANTEAM 2300) compatible scancodes. If other Welch Allyn wedge products are being used or are planned for future use, it is strongly recommended to program this selection for “YES” and use the function codes found in the Keyboard Function Codes Table 2 and Table 3 in the Appendix A.8 of the 2380Technical Manual. Otherwise, the 2380 will be programmed to use function codes in Keyboar
ページ13に含まれる内容の要旨
SCANCODE SCANTEAM 2380 Programming Menu SELECTION USE THIS PAGE (3) To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To reconfigure the 2380 to use the 2380 Function Codes. (Applies only to IBM XT, AT, and PS/2’s.) Refer to Appendix A.8 in 2380 Technical Manual for two options. To reconfigure the 2380 to use a new Scancode Table. Only applicable to customers who request new Scancode Table (that is, foreign keyboards). scan selections scan variables scan scan K2 SCA
ページ14に含まれる内容の要旨
SCANTEAM 2380 Information and Examples SYMBOLOGY SELECTION INDUSTRIAL INDUSTRIAL CODE OUTPUT FORMATS CODABAR aSX . . . XS Code 3 of 9 bSXX . . XXCS INTERLEAVED 2 of 5 eXX . . . XXC 2 of 5 fXX . . . . XX MSI gXX . . . XX Code 11 hXX . . . XXCC Code 93 iXX . . . . XX Code 128 jXX . . . . XX Where: a = Codabar Code ID b = Code 3 of 9 ID e = Interleaved 2 of 5 ID f = 2 of 5 ID g = MSI (Plessey) h = Code 11 ID i = Code 93 ID j = Code 128 ID S = Start/Stop Character X = Data Character C = Checksum Cha
ページ15に含まれる内容の要旨
SYMBOLOGY SCANTEAM 2380 Programming Menu SELECTION (CODES) USE THIS PAGE To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To specify desired bar code symbologies. To select symbology options. selections scan variables scan scan Enable *Yes/No scan CODABAR (ID = a) Minimum Length A *01–MAX Maximum Length B Min–48* S/S Xmit C *Yes/No Enable *Yes/No CODE 39 (ID = b) Minimum Length A *00–MAX ENTER Maximum Length B Min–48* S/S Xmit C Yes/No* Check Char. Req’d Yes/No
ページ16に含まれる内容の要旨
SCANTEAM 2380 Information and Examples SYMBOLOGY SELECTION RETAIL RETAIL CODE OUTPUT FORMATS Non–Zero Suppressed UPC–A and UPC–E Output Format UPC–A cNXXXXXXXXXXC UPC–A with 2 digit supplemental cNXXXXXXXXXXC–SS UPC–A with 5 digit supplemental cNXXXXXXXXXXC–SSSSS UPC–E cNXXXXXXXXXXC UPC–E with 2 digit supplemental cNXXXXXXXXXXC–SS UPC–E with 5 digit supplemental cNXXXXXXXXXXC–SSSSS Zero Suppressed UPC–A and UPC–E Output Format UPC–A cNXXXXXXXXXXC UPC–A with 2 digit supplemental cNXXXXXXXXXXC–SS
ページ17に含まれる内容の要旨
SYMBOLOGY SCANTEAM 2380 Programming Menu SELECTION (CODES) USE THIS PAGE To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To specify desired bar code symbologies. To select symbology options. selections scan variables scan scan scan Enable *Yes/No CODABAR (ID = a) Minimum Length A *01–MAX Maximum Length B Min–48* S/S Xmit C *Yes/No Enable *Yes/No CODE 39 (ID = b) ENTER Minimum Length A *00–MAX Maximum Length B Min–48* S/S Xmit C Yes/No* scan Check Char. Req’d Y
ページ18に含まれる内容の要旨
USER’S SCANTEAM 2380 Programming Menu NOTES 18
ページ19に含まれる内容の要旨
KEYBOARD LAYOUTS SCANTEAM 2380 Programming Menu Continued C5 C4 A1 A2 C6 B7 B8 B9 C3 A3 A4 A0 A5 A6 B4 B5 B6 B1 B2 B3 C2 A7 A8 A9 B0 C0 C1 IBM XT Keyboard A5 A6 A7 A8 A9 B0 D7 D8 C9 D1 A2 A3 A4 C3 A0 D6 B7 B8 B9 B5 B4 B5 B6 A0 B1 B2 B3 C0 C1 IBM PC/AT Keyboard A5 A6 A7 A8 A9 B0 C7 C8 C9 C5 A1 A2 A3 A4 C3 A0 B7 B8 B9 C6 B5 B4 B5 B6 A0 B1 B2 B3 C0 C1 IBM PS2–30 Keyboard 19
ページ20に含まれる内容の要旨
USER’S SCANTEAM 2380 Programming Menu NOTES 20
