ページ1に含まれる内容の要旨
Refresh
Personal Hygiene System™
OWNER’S MANUAL
Round EU44959 — ROUND FRONT
Elongated EV77959 — ELONGATED FRONT
This manual contains important safety information.
Please read carefully before product installation or use.
EX93000 Refresh Installation Manual 10/06
ページ2に含まれる内容の要旨
Important Safeguards CAUTION CAUTION For safety reasons, please read this entire manual before installation or use. Danger - Possibility of electric shock! Do not use harsh brushes or abrasive detergents to clean Use the correct voltage according to the specifications and the Refresh Personal Hygiene System™. Use only mild soap connect to a three-prong GFCI grounded outlet. and a soft cloth for cleaning. NOTE: This GFCI outlet should be installed prior to performing this installation. Ple
ページ3に含まれる内容の要旨
Before Installation Tools Needed • Flat head screwdriver • Universal wrench (included) • Phillips head screwdriver • Measuring tape NOTE: The included Universal Wrench will work for most applications. Depending on your toilet confi guration, an adjustable wrench may also be needed. Alternate Mounting Hardware Some toilets may not provide adequate access to the seat mounting holes preventing proper installation of the Standard Mounting Hardware. In this case you will need to use the Alternate
ページ4に含まれる内容の要旨
Installation (continued) 3) Install Mounting Plate (continued) L c) Adjust mounting plate so length (L) between the front of the toilet 3c bowl and the back of the mounting plate is as follows: Round (EU44959): L=18¼" (465 mm) Elongated (EV77959): L=20½"(495 mm) d) Tighten Mounting Bolts with screwdriver until the mounting plate is securely fastened to the toilet. 4) Connect T-Valve and Hoses NOTE: If your water supply line is rigid pipe, you may need to replace it before installing the R
ページ5に含まれる内容の要旨
Installation (continued) 8) Remote Control Installation a) Identify a location for the Remote Control that is visible and reachable from the toilet and that does not obstruct the IR signal. Depending on your wall type, you can install the screws directly or use anchor mounts (provided) as shown. b) If you prefer to not drill holes in your wall, you may use double sided foam tape to adhere bracket to wall. In this case, make sure to choose a tape with an adhesive that will not damage wall u
ページ6に含まれる内容の要旨
Operation Some features of the Refresh Personal Hygiene System™ are designed to function only when the seat is occupied. REMOTE CONTROL PANEL WARM WATER WASH INDICATOR LIGHTS Posterior (Rear) Feminine (Vaginal) Cleansing Cleansing power Water Temperature power save Low>Med>High>Off LCD Panel Seat Temperature seat heat Low>Med>High>Off seat sensor Warm Air Dryer On Low>Med>High AUXILIARY CONTROLS Powersave (backup for Remote) Function Decrease Increase AUX Stop Water Pressure Stop Adjustment (f
ページ7に含まれる内容の要旨
Operation (continued) Setting the Clock a) Press and hold the STOP button on the remote Control for over 5 seconds until the Clock flashes. b) Use the button to set the HOUR and the button to set the MINUTES. Power Save Mode The Refresh Personal Hygiene System™ includes a power saving feature to reduce electrical consumption when not in use. Once set, the Power save function turns the Refresh ON and OFF each day according to your programmed time settings. Setting the Power save Start and
ページ8に含まれる内容の要旨
Maintenance CAUTION CAUTION Always unplug the Refresh before cleaning! Seat Cleaning and Removal Use a soft, damp cloth and mild cleanser (such as dish soap) to wipe down the seat. DO NOT scrub or use harsh, abrasive products to clean the Refresh bidet seat. For a more thorough cleaning, you may remove the Refresh bidet seat. To release, push the button Press to located on the back right side of the seat and pull Release the Refresh bidet seat forward. Nozzle Cleaning It is recommended
