ページ1に含まれる内容の要旨
Installation Instructions &
Owner’s Manual
S12Q, S12Q-GOLD,
S24Q, S24Q-GOLD, S40Q
EPA # 57987-CN-001
425 Clair Road West, P.O. Box 1719 • Guelph, ON • N1H 7X4 • Canada
t. 519.763.1032 • f. 519.763.5069 • t.f. 1.800.265.7246
e. water@r-can.com • i. www.r-can.com
P/N 520022
January 2005
ページ2に含まれる内容の要旨
TABLE OF CONTENTS: Safety Instructions Page 1 Improved Ballast Features Page 1 Water Chemistry Page 2 Installing Your Disinfection System Page 2 Operating & Maintenance Instructions Page 3-4 Warning Systems Page 4-5 Warranty Page 5 Troubleshooting Page 6-8 Parts Page 9 Specifications Page 10 SYMBOLS: Caution Protective Ground Electrical Warning Fragile Eye Protection
ページ3に含まれる内容の要旨
SAFETY INSTRUCTIONS: WARNING - to guard against injury, basic safety precautions should be observed, including the following: 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. 2. CAUTION - Disconnect power before servicing. 3. DANGER - To avoid possible electric shock, special care should be taken since water is present near electrical equipment. Unless a situation is encountered that is explicitly addressed by the provided maintenance and troubleshooting sections, do not attempt repairs yourself, r
ページ4に含まれる内容の要旨
WATER CHEMISTRY: Water quality is extremely important for the optimum performance of your UV system. The following levels are recommended for installation: • Iron: < 0.3 ppm (0.3 mg/L) • Hardness*: < 7 gpg (120 mg/L) • Turbidity: < 1 NTU • Manganese: < 0.05 ppm (0.05 mg/L) • Tannins: < 0.1 ppm (0.1 mg/L) • UV Transmittance: > 75% (call factory for recommendations on applications where UVT < 75%) * Where total hardness is less than 7 gpg, the UV unit should operate efficiently provided the quar
ページ5に含まれる内容の要旨
OPERATING & MAINTENANCE INSTRUCTIONS: • Always disconnect power before performing any work on the ultraviolet disinfection system. • Regularly inspect your disinfection system unit to ensure that the UV light is still glowing and that its LED indicator is still glowing green. • Replace the UV lamp annually ( or biennially if seasonal cottage use) to ensure a high bacteria and virus kill rate. • Always drain the UV cell when closing a cottage or leaving the unit in an area subject to freezing
ページ6に含まれる内容の要旨
f) Re-assemble the quartz sleeve with spring in the UV chamber allowing the sleeve to protrude an equal distance from both ends of the UV chamber. g) Wet the o-rings and slide onto each end of the quartz sleeve and reassemble the gland nuts (hand tight is sufficient). h) Re-tighten all connections, turn on water and check for leaks. I) Re-install the UV lamp and lamp connector as per prior instructions. j) Reconnect system to power source. Note: If the system is put on a temporary by-pass or
ページ7に含まれる内容の要旨
into existing plumbing (1” for 12 & 24 gpm models). Install “normally-closed” solenoid valve within three (3) feet of disinfection system. Remove the screws on the left and right side of the front aluminum panel allowing this panel to swing open. Remove the circuit board cover plate to expose the circuit board. Remove the round, black plastic cap covering the access hole for the solenoid wire (cap located on back panel next to main power cord). Slide the solenoid power cord (part# CS-MOL) thro
ページ8に含まれる内容の要旨
TROUBLESHOOTING GUIDE Caution: When performing any work on the disinfection system unplug the unit first and never look directly at the burning UV lamp. SYMPTOM POSSIBLE CAUSES REMEDY • replace filter cartridge with appropriate five micron cartridge, • the sediment pre-filter is clogged Note: check source water supply PRESSURE DROP as fluctuations may occur in source pressure • clean sleeve with scale cleaner • quartz sleeve is stained or dirty and eliminate source staining proble
ページ9に含まれる内容の要旨
S12Q TROUBLESHOOTING GUIDE SYSTEM STATUS LAMP REMARKS STATUS AUDIBLE UV LAMP (GREEN ALARM LED) • Correct operating conditions, unit is functioning properly. ON OFF ON • The UV lamp is spent, requires replacement lamp. • UV lamp not connected to power source. Check connection and reconnect lamp. OFF ON OFF • Ballast has switched off. To reset ballast remove power to unit by disconnecting power cord from electrical plug for a minimum of 30 seconds then reapply power. • LED indicator burnt out
ページ10に含まれる内容の要旨
S12Q-GOLD & S24Q-GOLD TROUBLESHOOTING GUIDE SYSTEM STATUS UV REMARKS AUDIBLE INTENSITY UV LAMP ALARM (LED) • Correct operating conditions unit is functioning properly. GREEN OFF ON • System performance has declined due to stained or dirty quartz sleeve and or sensor lens, or the lamp is beyond its useful life. • Clean sleeve and sensor probe lens or replace if required. YELLOW OFF ON • Replace lamp with manufacturer replacement. • Replace sensor with manufacturer replacement. • Always Wet
ページ11に含まれる内容の要旨
S12Q PARTS BREAKDOWN S12Q-GOLD PARTS BREAKDOWN S36RL UV LAMP S36RL UV LAMP QS-012 QUARTZ SLEEVE QS-012 QUARTZ SLEEVE OR-212 O RING OR-212 O RING BA-ICE-3F BALLAST (100-130V/50-60Hz. or BA-ICE-3F BALLAST (100-130V/50-60Hz. or 200-250V/50-60Hz.) 200-250V/50-60Hz.) SUB-WH/LED512 LED INDICATOR ASSEMBLY CB-1240UV CIRCUIT BOARD (for 115V. unit) RN-001 RETAINING NUT CB-1240UV/2 CIRCUIT BOARD (for 230. unit) CS-001/Q CORD SET (120V.) RN-001 ALUMINUM RETAINING NUT CS-EU/Q EUROPEAN “SCHUKO” CORD SET (230
ページ12に含まれる内容の要旨
SPECIFICATIONS MODEL S12Q S12Q-GOLD S24Q S24Q-GOLD S40Q 109.8 lpm 109.8 lpm 219.6 lpm 219.6 lpm 367.2 lpm US Public Health (29 gpm) (29 gpm) (58 gpm) (58 gpm) (97 gpm) 2 16 mJ/cm 3 3 3 3 3 (6.6 m /Hr.) (6.6 m /Hr.) (13.2 m /Hr.) (13.2 m /Hr.) (22.0 m /Hr.) 56.8 lpm 56.8 lpm 113.6 lpm 113.6 lpm 189.3 lpm R-Can Standard (15 gpm) (15 gpm) (30 gpm) (30 gpm) (50 gpm) 2 30 mJ/cm 3 3 3 3 3 (3.4 m /Hr.) (3.4 m /Hr.) (6.8 m /Hr.) (6.8 m /Hr.) (11.4 m /Hr.) 41.6 lpm 41.6 lpm 83.3 lpm 83.3 lpm 140.1 lpm NS
