ページ1に含まれる内容の要旨
Installation
Instructions
3875.403
COLONY SOFT
3875.503
Spread Lavatory Faucet with
SpeedConnect™ Drain
Congratulations on purchasing your American Standard faucet with
SpeedConnect drain, a feature found only on American Standard faucets.
SpeedConnect Drain*
• 1/3 of the parts, installs in 1/3 of the time
No tools needed
Never needs adjustment
Certified to comply with ANSI A112.18.1
Guaranteed to seal properly the first time, every time.
M968886
*Your new American Standard faucet
ページ2に含まれる内容の要旨
INSTALL POP-UP DRAIN 2 Fig. A. Fig. B. REAR OF SINK Remove CLEAR PLASTIC COVER (1). Remove 1 CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A. 4 3 Drop DRAIN BODY (4) through sink drain 6 hole. Make sure WHITE FOAM GASKET (5) 5 is under flange of DRAIN BODY (4). Fig. B. SINK 2 Note: No plumber’s putty or caulk is required. DRAIN HOLE The CABLE ATTACHMENT POINT (6) must face towards the rear of the SINK. Fig. B. INSTALL BLACK GASKET 3 Install BLACK CONE GASKET (1) onto DRAIN BODY (2) fr
ページ3に含まれる内容の要旨
ATTACH CABLE CONNECTOR 6 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 1-1/4” O.D. 2 CHECK OPERATION OF POP-UP 7 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 2 MAKE WATER SUP
ページ4に含まれる内容の要旨
INSTALL HANDLE TRIM 9 5 4 LEVER HANDLE 4 Turn HANDLE STEM (1) to "OFF" position. Place the HANDLE ADAPTER (2) on the HANDLE STEM (1). Install the 3 ADAPTER SCREW (3) and tighten securely. 5 Position LEVER HANDLE (4) and place on ADAPTER (2). Install the HANDLE SCREW (5) and tighten securely. 3 ACRYLIC HANDLE 2 Turn HANDLE STEM (1) to "OFF" position. 2 Place the HANDLE ADAPTER (2) on the HANDLE STEM (1). 11 Position ACRYLIC HANDLE (3) and install on ADAPTER (2). Install the HANDLE SCREW (4) and t
ページ5に含まれる内容の要旨
SpeedConnect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. CAB
ページ6に含まれる内容の要旨
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice Fig. G. that the Loop is on one side of the Stopper. Fig. G. LOGO To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper s
