ページ1に含まれる内容の要旨
CHARGER / ENGINE
STARTER, 6/12V
Model 46944
ASSEMBLY and OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe THiS
ページ2に含まれる内容の要旨
Specifications Amperage Output 40 amps at 6 Volts (6 and 12 Volt) 100 amps at 6 Volts intermittent 2/10/40 amps at 12 Volts 200 amps at 12 Volts intermittent Timer 3 Hour Dimensions 16” W x 11-3/4” D x 31-3/4” H Cable Clamps 3/4” W x 6-1/2” L (Copper), 3-3/4” L, Color Coded Vinyl Grip Sleeves, Red (Positive), Black (Negative) Cable Length 79” Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, pa
ページ3に含まれる内容の要旨
9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 10. Maintain tools with care. Keep tools clean for better and safer performance. Inspect tool cords periodically, and if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 11. Disconnect power. Unplug Charger Engine Starter when not in use. 12. Avoid unintentional starting. Be sure the switch
ページ4に含まれる内容の要旨
Additional Battery Charger Safety Warnings: 1. Only use this Charger Engine Starter with lead acid, rechargeable type batteries. Remove battery caps to check liquid level inside battery. If liquid is not present or if liquid appears to be frozen, do not attempt to charge battery. 2. Do not use this Charger Engine Starter as a low voltage system power supply except in automotive applications. 3. Do not try to start the automobile engine when the battery is still charging. It may damage
ページ5に含まれる内容の要旨
Unpacking When unpacking, check to make sure the parts listed on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Assembly Refer to FIGURE 1 and FIGURE 2 below. 1. Place the Charger Engine Starter on its side. 2. Mount the Mounting Foot on the bottom using three screws. FIGURE 2 FIGURE 1 Note: Wheel Hubs must face inward. Handle Axle Cap Mounting Foot Cord Cleats Axle Bracket 3. Next, sli
ページ6に含まれる内容の要旨
Operation (continued) 7. After fully charging the battery, when the ammeter needle reads zero nearly, unplug the Charger Engine Starter line cord from the outlet or extension cord. 8. Remove the negative (black) cable clamp from the battery. 9. Remove the positive (red) cable clamp from the battery. Table 1 Battery Size / Rating Charge Rate* / Charging Time Hours** 12V 2 Amp 12V 10 Amp 12/6V 40 Amp Small Batteries Motorcycle 6 - 12 AH 3 - 6 NR NR Garden Tractor etc. 12 - 32 AH 3
ページ7に含まれる内容の要旨
Operation (continued) require 1 to 1-1/2 hours of charging at the 40 amp rate to reach the full charge state. For the same battery with its timer set to maximum, 3 hours overcharging will occur. Slight overcharging will not likely harm a battery that was otherwise in good condition. When the state of charge is unknown, start out with a timer setting of one hour or less. Hold: This position defeats the timer function, allowing for continuous operation. Use it when you want to charge more
ページ8に含まれる内容の要旨
Troubleshooting (continued) Symptom: Ammeter needle moves up to full charge, then drops to zero. Makes clicking noise. Probable Cause: 1. Battery is completely dead. 2. Defective battery. 3. Charger Engine Starter is resetting itself after circuit overload. 4. Circuit breaker is cycling. 5. Reverse con- nections at battery. Remedy: 1. Continue charging battery. Charger Engine Starter will continue to reset itself until the battery charge reaches a chargeable level. 2. Check an
ページ9に含まれる内容の要旨
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installatio
