ページ1に含まれる内容の要旨
Dell Precision Mobile Workstation M4700
Owner's Manual
Regulatory Model: P21F
Regulatory Type: P21F001
ページ2に含まれる内容の要旨
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2013 Dell Inc. All Rights Reserved. ™ ™ ™ ™ ™ ™ Trademarks used in this text: Dell , the DELL logo, Dell Precision , Precision ON ,ExpressCharge , Latitude , Latit
ページ3に含まれる内容の要旨
Contents 1 Working on Your Computer....................................................................................................... 7 Before Working Inside Your Computer.....................................................................................................................7 Recommended Tools................................................................................................................................................ 8 Turning Off Your Computer................
ページ4に含まれる内容の要旨
Installing the Video-Card Fan................................................................................................................................. 28 Removing the Coin-Cell Battery..............................................................................................................................28 Installing the Coin-Cell Battery...............................................................................................................................29 Removing the Palm
ページ5に含まれる内容の要旨
Assigning a System Password and Setup Password...................................................................................... 68 Deleting or Changing an Existing System and/or Setup Password..................................................................68 4 Diagnostics.................................................................................................................................71 Enhanced Pre-Boot System Assessment (ePSA) Diagnostics...................................
ページ6に含まれる内容の要旨
6
ページ7に含まれる内容の要旨
1 Working on Your Computer Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist: • You have read the safety information that shipped with your computer. • A component can be replaced or--if purchased separately--installed by performing the removal procedure in reverse orde
ページ8に含まれる内容の要旨
NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer. 7. Remove the main battery. 8. Turn the computer top-side up. 9. Open the display. 10. Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display. CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the
ページ9に含まれる内容の要旨
2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down.. 2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your operating system, press and hold the power button for about 4 seconds to turn them off. After Working Inside Your Computer After you complete any replacement procedure, ensure you connect any external devices, cards, and cables b
ページ10に含まれる内容の要旨
10
ページ11に含まれる内容の要旨
2 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Removing the Secure Digital (SD) Card 1. Follow the procedures in Before Working Inside Your Computer. 2. Press in on the SD card to release it from the computer. Slide the SD card out of the computer. Installing the SD Card 1. Push in the SD card into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer. Rem
ページ12に含まれる内容の要旨
3. Flip and remove the battery from the computer. Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your Computer. Removing the Subscriber Identity Module (SIM) Card 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery. 12
ページ13に含まれる内容の要旨
3. Slide the SIM card out from the slot . Installing the Subscriber Identity Module (SIM) Card 1. Push in the SIM card into its slot. 2. Install the battery. 3. Follow the procedures in After Working Inside Your Computer. Removing the Base Cover 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery. 3. Remove the screws that secure the base cover to the computer. Press the rubber tabs towards the rear of the computer to disengage the base cover. 13
ページ14に含まれる内容の要旨
4. Flip and remove the base cover from the computer. 14
ページ15に含まれる内容の要旨
Installing the Base Cover 1. Slide in and place the base cover to align with the screw holes correctly on the computer. 2. Tighten the screws to secure the base cover to the computer. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer. Removing the Keyboard Trim 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery. 3. Pry up the keyboard trim starting from the top-inner edge. 4. Pry up the bottom edge of the keyboard trim from
ページ16に含まれる内容の要旨
Installing the Keyboard Trim 1. Toe-in the keyboard trim from the front and align it to its original position on the computer. Ensure that the hard-tab on the left corner snaps into place. 16
ページ17に含まれる内容の要旨
2. Press along the sides of the keyboard trim until it snaps in place. 3. Install the battery. 4. Follow the procedures in After Working Inside Your Computer. Removing the Keyboard 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) battery b) keyboard trim 3. Remove the screws that secure the keyboard to the computer. 17
ページ18に含まれる内容の要旨
4. Starting from the bottom of the keyboard, separate the keyboard from the computer and flip the keyboard over. 5. Disconnect the keyboard-data cable from the system board and remove the keyboard. 18
ページ19に含まれる内容の要旨
Installing the Keyboard 1. Connect the keyboard-data cable to the system board. NOTE: Ensure that you fold the keyboard-data cable in perfect alignment. 2. Press the keyboard in its compartment. 3. Tighten the screws to secure the keyboard to the computer. 4. Press over the cross section of the following keys to secure the keyboard to the computer: a) , , and keys b) over the <9> key c) NUMLOCK <9> key 19
ページ20に含まれる内容の要旨
5. Install the: a) keyboard trim b) battery 6. Follow the procedures in After Working Inside Your Computer. Removing the Primary Memory 1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the: a) battery b) base cover 3. Pry the retention clips away from the primary memory until it pops up. Lift the primary memory and remove it from the computer. Installing the Primary Memory 1. Insert the primary memory into the memory socket. 2. Press the clips to secure the primary mem
