ページ1に含まれる内容の要旨
Operating Instructions Installation Manual
Electronic Board
Operating Instructions
[Stand (option)] [Wall-mounting (option)] With Installation Manual
Stand and wall-mounting kit are optional. (for qualified service personnel)
Model No. UB-7325
• Before operating this unit, please read these instructions completely.
After reading them, preserve them carefully for future reference.
� Because of the nature of the print film, all the printed text will remain on the film.
� This product is designed f
ページ2に含まれる内容の要旨
Thank you for purchasing the Panasonic Electronic Board. For optimum performance and safety, please read these instructions carefully. Accessories Q’ty Q’ty � Thermal transfer film . . . . . . . . . . . . . . 1 � Letter size copy paper . . . . . . . . . . . . . 20 � Markers (red, black, and blue) . . . . . . 1 each � Software CD-ROM . . . . . . . . . . . . . . . 1 � Operating Instructions . . . . . . . . . . . . . 1 � Warranty card
ページ3に含まれる内容の要旨
Operating Instructions Table of Contents Page For Your Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Before � CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 You Start Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 � Control panel . . . . . .
ページ4に含まれる内容の要旨
For Your Safety For Your Safety CAUTION: TO PREVENT RISK OF ELECTRIC SHOCK HAZARD, DO NOT REMOVE THE COVER OF THIS PRODUCT, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR ANY TYPE OF MOISTURE. THE SOCKET-OUTLET MUST BE NEAR THIS EQUIPMENT AND MUST BE EASILY ACCESSIBLE. The product should be used only with the power cord that is supplied by the manufacturer. Stop operation immediately if your product emits smoke,
ページ5に含まれる内容の要旨
Operating Instructions Precautions Precautions Never remove the cover, take apart or modify the Do not position the electronic board in a location where product. This will void the warranty. it is unstable. Do not put drinks, other liquids or heavy items on the After installing or moving the electronic board, lock the tray or screen. casters and set the fall-prevention extension legs. Push to lock Locking the casters (Push this side) Do not use the electronic board in an excessively If the ele
ページ6に含まれる内容の要旨
Precautions Do not lean against the screen or on the cover (lower), Have the unit installed, removed and even if the electronic board is mounted on the wall. disposed of only by qualified service personnel. When the unit will no longer be used, in order CHOKING HAZARD to prevent it from falling, do not leave the unit Keep the marker’s cap out of reach of installed, but remove it. If the unit falls, it can children to prevent swallowing. cause injury. ■ CD-ROM To prevent the CD-ROMs from a
ページ7に含まれる内容の要旨
Operating Instructions Precautions � Do not install the unit where it may be exposed to direct sunlight, near heating equipment, or Installation near air-conditioning vents as this may cause stretching and/or discoloration of the screen. � Do not install the unit in strong sunlight or strong lighting. Proper copying may become impossible. � Do not install the unit in locations where the temperature may change suddenly as this may disable the unit’s ability to make copies. � Make thick and da
ページ8に含まれる内容の要旨
Part Names and Functions Part Names and Functions Scanner Screen One screen (with no ruled lines) of four screens can also be used for a projector (see page 14). Tray Printer Stand The stand is optional. Output Port Control Panel This port holds up to 10 (See page 9 for details.) sheets of output paper. Power Switch ON Printer Open Lever OFF Push down this lever to open the printer door. AC Inlet Cord Holder Power Cord Printer Door Open this door to load a Paper Cover thermal transfer film
ページ9に含まれる内容の要旨
Operating Instructions Part Names and Functions ■ Control panel Reverse Key Contrast/Remaining Film Advance Key Indicator Contrast Key Multi-Copy/Stop Key Copy Key Multi-Copy/Error Indicator Panel Name Description This lamp indicator notifies the user when the time to replace the thermal transfer film is approaching (estimated) and of the printing contrast used during copying. Indicator off: Normal printing contrast Indicator on: Darker than normal printing contrast Contrast/ Indicator flashing
ページ10に含まれる内容の要旨
Installing the Thermal Transfer Film 2) Insert the blue shaft into the front left hole. Installing the Thermal Transfer Film Install the thermal transfer film in the printer. Set the power switch to on ( I ). Blue shaft 1 � “ ” will flash on the Multi-Copy/Error Indicator when the thermal transfer film has run out. � The screen will move to home position and stop. ON 3) Place the blue gear on the front right groove. OFF Blue gear Push down the printer open lever and open 2 the printer door.
ページ11に含まれる内容の要旨
Operating Instructions Loading Copy Paper Tighten the film, then close the printer door. 4 Loading Copy Paper 1) Rotate the blue gear in the direction of the arrow to take up the slack on the film. It is possible to load up to 40 sheets of Letter size 2 copy paper [assuming a paper weight of 80 g/m (20 lb.)]. Note that only Letter size paper may be used. When the unit is first used or when “ ” flashes on the Multi-Copy/Error Indicator to indicate that the unit is out of paper, load copy pap
ページ12に含まれる内容の要旨
Loading Copy Paper Pull the paper cover forward as shown in the Close the paper cover until a click is heard. 2 4 figure. Note To prevent paper jams such as those caused 3 by multiple sheets feeding at once, fan the � Close the paper cover, or the unit will not paper thoroughly, square it, align it with the work properly. guide inside, and insert as far as it will go. � The paper cover should be closed to make copies properly. Confirm the both latches are locked. Guide Maximum paper limit
ページ13に含まれる内容の要旨
Operating Instructions Making Copies Note Making Copies � Do not use paper that has been copied on one side by this printer as copy paper in this This section describes how to copy text and unit or in any other copiers or printers as this illustrations drawn on the screen. may result in dirty rollers, degradation of printing quality, paper jams, and streaks and Set the power switch to on ( I ). smudges on output paper. 1 � Do not write on the back side of the output � “ ” will light on th
ページ14に含まれる内容の要旨
Using the Projector Screen / Replacing the Thermal Transfer Film Using the Projector Replacing the Thermal Screen Transfer Film One of four screens of this electronic board can also The unit is capable of producing about 15 more copies be used as the projector screen. The screen has no when the Contrast/Remaining Film Indicator begins to ruled lines so the projected image is easy to see. flash. The unit has run out of thermal transfer film and can no longer make copies when the Multi-Copy/Er
ページ15に含まれる内容の要旨
Operating Instructions Paper Jams Install the thermal transfer film. 4 Paper Jams � Refer to steps 3 and 4 in the section of “Installing the Thermal Transfer Film” on Remove paper jams by the following procedure when page 10. copy paper does not come out of the output port or � “ ” flashing on the Multi-Copy/Error when “” flashes on the Multi-Copy/Error Indicator. Indicator will go out. Push down the printer open lever to open the Note 1 printer door. � If “ ” is still flashing after closi
ページ16に含まれる内容の要旨
Paper Jams To prevent paper jams such as those caused Turn the power on. 3 5 by multiple sheets feeding at once, fan the � “ ” will light on the Multi-Copy/Error Indicator paper thoroughly, square it, align it with the to indicate that the unit is ready to copy. guide inside, and insert as far as it will go. � The screen will move to home position and stop. ON OFF Guide Maximum paper limit Note � Do not stack more copy paper in the unit than the maximum paper limit indicated by the guide (
ページ17に含まれる内容の要旨
Operating Instructions Computer Interfacing ■ Contents of CD-ROM Computer Interfacing The provided CD-ROM includes the following items. Drivers and software must be installed in your � USB driver computer to use Board Image Capture, Quick Image � Printer driver Navigator, Panasonic-DMS, printer and TWAIN driver. � TWAIN driver � Board Image Capture Allows you to scan hand-written text and ■ System requirements diagrams on the Panaboard and save the scanned image as a PDF file. IBM® PC/AT® or
ページ18に含まれる内容の要旨
Computer Interfacing ■ Installing Drivers / Board Image 6 When the following window appears, check Capture that the electronic board is not connected to your computer and click [OK]. The USB, printer, TWAIN driver and Board Image Capture are installed in your computer by following procedures. Note � Do not yet connect a USB cable to the electronic board. 1 1 Power on your computer and start Windows* . � Log on as an administrator for Windows 2000, Windows XP or Windows Vista. 1 * Microsof
ページ19に含まれる内容の要旨
Operating Instructions Computer Interfacing In such a case, double-click “Menu.exe” in 8 Follow the on-screen instructions if the wizard the CD-ROM from the Explorer. windows appear. � If the Autoplay dialog box appears in � If the wizard window is displayed to select Windows Vista, click “Run Menu.exe”. the file (##.inf) for the printer driver in Windows XP, select “windows\inf\oem##.inf”. 3 When “Welcome” window appears, click � If the wizard window is displayed to connect [Next]. to th
ページ20に含まれる内容の要旨
Computer Interfacing 2 In the Control Panel, double-click Add/ Remove Programs (Windows XP: Add or Remove Programs, Windows Vista: Uninstall a program). 3 Select the software you want to remove, then remove it. � To remove the USB and TWAIN driver, select Panaboard UB5-7 Driver. To remove Board Image Capture, select Panasonic Board Image Capture. To remove Quick Image Navigator, select Note Panasonic Quick Image Navigator. � If the Panaboard Operation Panel does not 4 Follows the instruct
