ページ1に含まれる内容の要旨
OPERATOR’S
MANUAL
Axion / 150Z Series
18.5, 21, 26HP Zero-Turn Riders
Mfg. No. Description
7800611 Simplicity Axion Model ZT18533, 18.5HP w/ 33” Mower
7800616 Simplicity Axion Model CZT18533, 18.5HP w/ 33” Mower (California Model)
7800620 Snapper 150Z Model SC18533, 18.5HP w/ 33” Mower
7800625 Snapper 150Z Model CSC18533, 18.5HP w/ 33” Mower (California Model)
7800612 Simplicity Axion Model ZT2142, 21HP w/ 42” Mower
7800617 Simplicity Axion Model CZT2142, 21HP w/ 42” Mower (California Model)
780
ページ2に含まれる内容の要旨
Not for Reproduction
ページ3に含まれる内容の要旨
TABLE OF CONTENTS Safety Rules Service & Adjustments General Operation...................................................4 Ground Speed Control Lever Adjustment .............30 Transportation & Storage ........................................4 Speed Balancing Adjustment................................30 Slope Operation ......................................................5 Cutting Height Adjustment ....................................30 Towed Equipment...........................................
ページ4に含まれる内容の要旨
SAFETY RULES Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is capable of amputating hands and feet and throwing objects. The triangle in text signifies important cautions or warnings which must be followed. 19. Follow the manufacturer’s recommendations for wheel GENERAL OPERATION weights or counterweights. 1.
ページ5に含まれる内容の要旨
SLOPE OPERATION WARNING Slopes are a major factor related to loss-of-control and tip- Never operate on slopes greater than 17.6 percent over accidents, which can result in severe injury or death. (10°) which is a rise of 3-1/2 feet (106 cm) vertically in Operation on all slopes requires extra caution. If you cannot 20 feet (607 cm) horizontally. back up the slope or if you feel uneasy on it, do not operate Select slow ground speed before driving onto slope. on it. Use extra caution when operati
ページ6に含まれる内容の要旨
6 THIS IS A 10 DEGREE SLOPE FOLD ALONG DOTTED LINE SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 10 DEGREES MAX. WARNING: To avoid serious injury, operate your unit up and down the face of slopes, never across the face. Do not operate on slopes greater than 10 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. Braking may be affected by attachments. Reduce speed
ページ7に含まれる内容の要旨
13. If the fuel tank must be drained, it should be drained SERVICE AND MAINTENANCE outdoors. Safe Handling of Gasoline 14. Replace faulty silencers/mufflers. 1. Extinguish all cigarettes, cigars, pipes, and other 15. Maintain or replace safety and instruction labels as sources of ignition. necessary. 2. Use only approved gasoline containers. 16. Use only authorized replacement parts when making 3. Never remove the gas cap or add fuel with the engine repairs. running. Allow the engine to cool be
ページ8に含まれる内容の要旨
SAFETY & OPERATION DECALS All DANGER, WARNING, CAUTION and instructional This unit has been designed and manufactured to messages on your rider and mower should be carefully provide you with the safety and reliability you would read and obeyed. Personal bodily injury can result when expect from an industry leader in outdoor power these instructions are not followed. The information is for equipment manufacturing. your safety and it is important! The safety decals below Although reading this
ページ9に含まれる内容の要旨
SAMPLE IDENTIFICATION NUMBERS ID Tag When contacting the service center for replacement parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identification numbers, and engine serial numbers in the space provided for easy access. The identification tag is located on the underside of the PRODUCT REFERENCE DATA seat. Tilt the seat forward to access the ID tag. Model Description Name/Number Part Number Unit Serial Number Date Purchased ENGINE
ページ10に含まれる内容の要旨
OPERATION Left Right Ground Speed Ground Speed Control Lever Control Lever Ground Speed Levers - Ground Speed Levers - DRIVE Positons START/PARK Positons Mower Cutting Height Switch Parking Brake Lever Choke Engine Speed Parking Brake Lever - Parking Brake Lever - (Fast) ENGAGE Positon DISENGAGE Positon Fuel Tank Cap Engine Speed (Slow) CONTROL FUNCTIONS RUN OFF START The information below briefly describes the function of individual controls. Starting, Transmission Mower Blade stopping, dri
ページ11に含まれる内容の要旨
Mower Cutting Height Switch Mower Blade Switch To increase the mower cutting height (raise the mower The yellow mower blade switch turns the mower blades deck), press the top of the yellow cutting height switch. on and off. To turn the mower blades ON, pull the switch To decrease mower cutting height (lower the mower up. To turn the mower blades OFF, push the switch deck), press the bottom of the switch. Mower cutting down. Always set the engine speed control to FAST height range is approxim
ページ12に含まれる内容の要旨
CHECKS BEFORE STARTING � Check that the crankcase oil is filled to full mark on dipstick (see CHECK ENGINE OIL in the Maintenance section). � Fill the fuel tank with fresh fuel. FUEL RECOMMENDATIONS For daily operation: Use only unleaded gasoline with a pump sticker octane rating of 87 or higher. Gasohol (up to 10% ethyl alcohol, 90% unleaded gasoline by volume) is approved as a fuel. Methyl Teriary Butyl Ether (MTBE) and unleaded gasoline blends (up to a maximum of 15% A MTBE by volume) are
ページ13に含まれる内容の要旨
9. Stop the rider and engine (see STOPPING THE EMERGENCY STOPPING RIDER AND ENGINE). In the event of an emergency the engine can be stopped PUSHING THE RIDER BY HAND by simply turning the ignition switch to STOP. Use this method only in emergency situations. For normal engine NOTE: Do not disengage the transmissions if parked on shut down follow the procedure given in STOPPING THE a slope. RIDER AND ENGINE. 1. Turn the mower blades OFF, push the ground speed control levers out to their START/P
ページ14に含まれる内容の要旨
Smooth Travel DRIVING PRACTICE - The lever controls of the BASIC DRIVING zero turn rider are WARNING: Never operate on slopes greater than 17.6% highly responsive. (10°). See SLOPE OPERATION in the safety section. The BEST method of Zero turn riders operate differently from other four- handling the ground wheeled vehicles. The drive wheels are also your speed control levers is in steering wheels. If you cannot drive the unit on a hill, you three steps — as shown will not be able to steer th
ページ15に含まれる内容の要旨
Practice Turning Around a Corner Practice Turning In Place While traveling forward allow one handle to gradually To “zero turn” means to turn in place. To turn in place, return back toward neutral. Practice several times before gradually move one ground speed control lever forward mowing. from neutral and one lever back from neutral simultaneously. Repeat several times. NOTE: To prevent damaging your lawn by pivoting directly on the tire tread, it is best to keep both wheels going at least slig
ページ16に含まれる内容の要旨
MOWER DECK REMOVAL & A INSTALLATION - 33” DECKS B C NOTE: Perform mower removal and installation on a hard, level surface such as a concrete floor. WARNING A After lowering the mower cutting height, engage parking brake, turn off the mower blades, turn the ignition switch to STOP, and remove key before attempting to install or remove the mower. Removing the Mower Deck 1. Turn the mower blades OFF, put the ground speed control levers in START/PARK position, engage the D parking brake, turn the i
ページ17に含まれる内容の要旨
MOWER DECK REMOVAL & B C INSTALLATION - 42” DECKS A NOTE: Perform mower removal and installation on a hard, level surface such as a concrete floor. WARNING After lowering the mower cutting height, engage D parking brake, turn off the mower blades, turn the ignition switch to STOP, and remove key before attempting to install or remove the mower. Removing the Mower Deck 1. Turn the mower blades OFF, put the ground speed Figure 12. Mower Hitch Components - 42” Decks control levers in START/PARK po
ページ18に含まれる内容の要旨
6. Turn the ignition switch OFF and remove the key. MOWER DECK REMOVAL & Remove the 4x4 wood blocks. INSTALLATION - 52” DECKS 7. Insert ratchet into 3/8” (9.5 mm) square hole in idler pulley arm (A, Figure 14) and pull to release belt NOTE: Perform mower removal and installation on a tension. Install the mower belt (B) as shown in Figure 14. hard, level surface such as a concrete floor. WARNING C E B D F After lowering the mower cutting height, engage parking brake, turn off the mower blades, tu
ページ19に含まれる内容の要旨
MAINTENANCE MAINTENANCE SCHEDULE The following schedules should be followed for normal care of your rider and mower. Before Spring 8 25 100 200 Yearly RIDER MAINTENANCE, All Models Each Use & Fall Hours Hours Hours Hours Clean Debris from Rider and Engine Compartment * � Clean Debris from Engine Cooling Areas & Air Filter * � Check Tire Pressure � Lubricate Rider & Mower * � Clean Deck & Check/Replace Mower Blades � Clean Battery & Cables � Check Rider Safety System ** � � � Check / Adjust PTO
ページ20に含まれる内容の要旨
Rider Maintenance Items WARNING Move the ground speed levers to START/PARK positions, engage the parking brake, turn the mower blades OFF, turn the ignition switch OFF, and wait for all moving parts to stop before accessing the engine compartment or performing any maintenance procedures. ACCESSING THE ENGINE COMPARTMENT Figure 16. Accessing the Engine Compartment Lift up on the back edge of the seat deck to access the engine compartment. A B CLEAN DEBRIS FROM RIDER AND ENGINE COMPARTMENT Serv
