ページ1に含まれる内容の要旨
ATTACHMENT
OPERATOR’S
MANUAL
Clean Sweep
Twin Catcher
Clean Sweep Twin Catcher
Mfg. No. Description
1695164 Clean Sweep Twin Catcher
1733420
Rev. 00
Rev. Date 05/2006
TP 100-4297-00-AT-N
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Table of Contents Safety Rules & Information General Warnings............................................2 Safety Decals ..................................................2 General Operating Instructions Before Operation .............................................3 Mowing with the Catcher .................................3 After Operation ................................................3 Storing the Grass Catcher...............................3 Initial Installation Hitch Installation .........
ページ4に含まれる内容の要旨
Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. GENERAL WARNINGS � Know the unit’s controls and how to stop quickly. bag that meets manufacturer’s durability standards. READ THE OPERATOR’S MANUALS. � If the mower stall
ページ5に含まれる内容の要旨
General Operating Instructions Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. For this reason, BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the u
ページ6に含まれる内容の要旨
Initial Installation WARNING Before beginning any service work turn off the B PTO, set the parking brake, turn off the ignition, A and disconnect the spark plug wire(s). Initial Installation Hitch Installation A 1. Slide the 5/16-18 speed nut (A, Figure 1) onto rear frame support (E) through square hole (C) so that the threaded side (B) is on the inside of tractor. C E 2. Secure the 5/16-18 shoulder bolt (D) as shown. D 3. Repeat on the other side. Figure 1. Install Spacer (left side shown) A.
ページ7に含まれる内容の要旨
Pin Installation C B D A B B A C Figure 4. Install Mounting Plate A. Carriage Bolts, 5/16-18 x 3/4 Figure 3. Install Pin B. Push Nuts, 5/16 A. Lower Chute C. Mower Deck Housing B. Locknut, 1/4-20 C. Pin D. Carriage Bolt, 1/4-20 x 5/8 Component Installation PIN INSTALLATION ON LOWER CHUTE 1. Insert the head of pin (C, Figure 3) through front hole of lower chute (A). Secure with 1/4-20 x 5/8 carriage bolt (D) and 1/4-20 lock nut (B) as shown. F B CARRIAGE BOLT AND PUSH NUT INSTALLATION MOWER
ページ8に含まれる内容の要旨
Latch Installation INSTALL LATCH AND HINGE TO COVER ASSEMBLY C 1. Install the latch (B, Figure 6) to the cover assembly (A) securing with #10-24 x 5/8 screws (D) and #10-24 A locknuts (C) as shown. B 2. Install the hinge (E) to cover assembly securing with 1/4-20 x 1/2 screws (G) and 1/4-20 locknuts (F). D F F E G Figure 6. Install Latch & Hinge to Cover Assembly A. Cover Assembly B. Latch C. Locknuts, ESNA, #10-24 D. Screws, #10-24 x 5/8 E. Hinge F. Locknuts, 1/4-20 G. Screw, Slotted, 1/4-20 x
ページ9に含まれる内容の要旨
Tube Installation C E C G F C F C G E A D D B C G D F Figure 9. Install Center Tube and End Caps D A. Center Tube B. Channel Assembly F C. Lockwashers, 5/16 B D. Nuts, 5/16-24 A E. Screw, Special, 5/16-24 D F. Tube Ends G. End Caps Figure 8. Install “U” Tube A. “U” Tube B. Channel Assembly C. Carriage Bolts, 5/16-18 x 1-3/4 D. Nuts, Nylock, 5/16-18 E. “L” Channel F. Saddle Brackets G. Capscrew, 5/16-18 x 3/4 C INSTALL TUBES AND END PLUGS D 1. Install the center tube (A, Figure 9) to RH side of
ページ10に含まれる内容の要旨
Bag, Chute and Tube Installation Bag, Chute and Tube Installation A INSTALL COLLECTOR BAGS 1. Raise the cover (A, Figure 12). 2. Slide collector bags (B) onto tubes (C) with the white C bar towards the rear. Note: It may be necessary to fold seat forward to allow cover to stay in the raised position. B Figure 12. Install Collector Bags A. Cover B. Collector Bags C. Tubes LOWER DISCHARGE CHUTE INSTALLATION 1. Lift discharge deflector up (E, Figure 13). E A 2. Place the front hole of the lower c
ページ11に含まれる内容の要旨
Tube and Chute Installation CONNECTING UPPER & MIDDLE TUBE 1. Slide the upper tube (A, Figure 14) into cover (B) aligning ridge (C) with cutout (D) as shown. D 2. Slide middle tube (D, Figure 15) into upper tube (E). 3. Slide middle tube (D) over boot (A). Pull strap (B) and place hole completely over pin (C). 4. Secure upper tube (E) over middle tube (D) and C secure tubes together using 1/4 x 3/4 screw (F) and correct hole. B A Figure 14. Install Upper Tube to Cover A. Upper Tube B. Cover C.
ページ12に含まれる内容の要旨
Normal Removal & Installation E Normal Removal & Installation A Collector Installation D Note: See previous pages for more detailed installation F and operation instructions if necessary. 1. Lift discharge deflector up (E, Figure 16). 2. Place the front hole of the lower chute (A) onto carriage bolt (C) as shown. Slide front edge of lower chute (A) under hinge bracket (G). G 3. Place the rear hole of the lower chute (A) onto carriage bolt (F) as shown. 4. Secure knob (B) onto carriage bolt (C)
ページ13に含まれる内容の要旨
Normal Removal F E M L G J A B C K I D H A. Channel Assembly H. Lower Chute B. Cover I. Pin C. Pin J. Middle & Upper Tube D. Hitch K. Strap, Middle E. Bag L. Ridge F. White Bar M. Ridge Cutout G. Tubes Figure 17. Normal Installation & Removal Collector Removal WARNING OPERATION WITHOUT BAGGER For operation without bagger, the mower deflector MUST be properly installed in the down position and retained by the spring latch. 4. Lift discharge deflector up (E, Figure 16). 5. Remove wing nut (D) fr
ページ14に含まれる内容の要旨
Simplicity Mfg. Inc. - Snapper Products 535 Macon Street McDonough, GA 30253 www.Snapper.com © Copyright 2006 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA.
