ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
To The Owner 1 Thank You Thank you for purchasing a Lawn Mower manufactured by This product has met the rigid safety standards of the Outdoor Troy-Bilt LLC. It was carefully engineered to provide excellent Power Equipment Institute and an independent testing performance when properly operated and maintained. laboratory. If you have any problems or questions concerning the machine, phone a authorized Troy-Bilt service dealer or contact Please read this entire manual prior to operating the eq
ページ3に含まれる内容の要旨
Important Safe Operation Practices 2 WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol. HEED ITS WARNING! CALIFORNIA PROPOSITION 65 WARNING: Engine Exhaust, some of its constituents, and certain v
ページ4に含まれる内容の要旨
12. A missing or damaged discharge cover can cause blade 27. When starting engine, pull cord slowly until resistance contact or thrown object injuries. is felt, then pull rapidly. Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than 13. Many injuries occur as a result of the mower being pulled you can let go. Broken bones, fractures, bruises or sprains over the foot during a fall caused by slipping or tripping. could result. Do not hold on to the mow
ページ5に含まれる内容の要旨
3. Check the blade and engine mounting bolts at frequent Service intervals for proper tightness. Also, visually inspect blade for damage (e.g., bent, cracked, worn) Replace blade with Safe Handling Of Gasoline: the original equipment manufacture’s (O.E.M.) blade only, 1. To avoid personal injury or property damage use extreme listed in this manual. “Use of parts which do not meet the care in handling gasoline. Gasoline is extremely flammable original equipment specifications may lead to i
ページ6に含まれる内容の要旨
Spark Arrestor Average Useful Life According to the Consumer Products Safety Commission WARNING: This machine is equipped with an (CPSC) and the U.S. Environmental Protection Agency (EPA), internal combustion engine and should not be used this product has an Average Useful Life of seven (7) years, or 140 on or near any unimproved forest-covered, brush hours of operation. At the end of the Average Useful Life, buy covered or grass-covered land unless the engine’s a new machine or have the
ページ7に含まれる内容の要旨
ページ8に含まれる内容の要旨
Assembly & Set-Up 3 Contents of Carton • One Lawn Mower • One Lawn Mower Operator’s Manual • One Bottle of Oil • One Grass Catcher • One Engine Operator’s Manual • One Hardware Pack • One Side Discharge Chute 2. Insert a carriage bolt from the hardware pack into the Assembly upper hole on the handle mounting bracket. Secure with NOTE: This unit is shipped without gasoline or oil in the engine. one plastic wing nut, also included in the hardware pack. Fill up gasoline and oil as instructed in
ページ9に含まれる内容の要旨
ページ10に含まれる内容の要旨
ページ11に含まれる内容の要旨
Controls and Features 4 Blade Control Recoil Starter Grass Catcher Side Discharge Chute Mulch Plug Cutting Height Adjustment Levers Figure 4-1 Grass Catcher Blade Control The grass catcher, located at the rear of the mower, is used to bag The blade control is attached to the upper handle of the mower. the grass clippings for disposal at another site. Once the bag is Depress and squeeze it against the upper handle to operate the full, it has to be removed from the mower and emptied before
ページ12に含まれる内容の要旨
ページ13に含まれる内容の要旨
Using Your Lawn Mower Using Grass Catcher Be sure lawn is clear of stones, sticks, wire, or other objects You can use the grass catcher to collect clippings while you are which could damage lawn mower or engine. Such objects could operating the mower. be accidently thrown by the mower in any direction and cause 1. Attach grass catcher following instructions in the serious personal injury to the operator and others. “Assembly & Set-Up” section. Grass clippings will automatically collect in ba
ページ14に含まれる内容の要旨
ページ15に含まれる内容の要旨
Engine Care Replacing Rear Flap A list of key engine maintenance jobs required for good 1. To remove rear flap, lift rear door, and press flap in on performance by the mower is given below. Follow the either side to remove from hole. See Fig. 6-2. accompanying engine manual for a detailed list and instructions. • Maintain oil level as instructed in engine manual. • Service air cleaner every 25 hours under normal conditions. Clean every few hours under extremely dusty conditions. Poor engine
ページ16に含まれる内容の要旨
Service 7 WARNING: An unbalanced blade will cause Blade Care excessive vibration when rotating at high speeds. It WARNING: When removing the cutting blade for may cause damage to mower and could break sharpening or replacement, protect your hands with causing personal injury. a pair of heavy gloves or use a heavy rag to hold the 5. Lubricate the engine crankshaft and the inner surface of blade. the blade adapter with light oil. Slide the blade adapter Periodically inspect the blade adapt
ページ17に含まれる内容の要旨
Troubleshooting 8 Problem Cause Remedy Engine Fails to start 1. Blade control disengaged. 1. Engage blade control. 2. Spark plug boot disconnected. 2. Connect wire to spark boot. 3. Fuel tank empty or stale fuel. 3. Fill tank with clean, fresh gasoline. 4. Engine not primed (if equipped with primer). 4. Prime engine as instructed in the Operation section. 5. Faulty spark plug. 5. Clean, adjust gap, or replace. 6. Blocked fuel line. 6. Clean fuel line. 7. Engine flooded. 7. Wait a few minutes to
ページ18に含まれる内容の要旨
Model Series 430 1
ページ19に含まれる内容の要旨
Model Series 430 Ref Ref Part Number Description Part Number Description No. No. 1 747-1161A Blade Control Handle 26 687-02337 Pivot Arm Assy RH (8” wheel) 687-02338 Pivot Arm Assy LH (8” wheel) 2 749-1092A Upper Handle 27 736-0524B Blade Bell Support 3 747-04080A Grass Catcher Frame 4 749-0928A Lower Handle 28 787-01290 Front Adjustment Plate 5 720-0279 Wing Nut 29 720-0426 Adjustment Lever Knob 30 732-0404 Spring Lever Assembly 6 710-1205 Rope Guide 31 736-0270 Bell Washer 7 710-1174 Carriage
ページ20に含まれる内容の要旨
MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by Troy-Bilt LLC with c. Routine maintenance items such as lubricants, filters, blade respect to new merchandise purchased and used in the United States sharpening, tune-ups, brake adjustments, clutch adjustments, and/or its territories and possessions, and by MTD Products Limited deck adjustments, and normal deterioration of the exterior finish with respect to new merchandise purchased and used in Canada due to
