ページ1に含まれる内容の要旨
Assembly Guide
®
EFX 536i
TM
Elliptical Fitness Crosstrainer
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Thank you for choosing Precor. For proper installation, please read this Required Tools guide thoroughly and follow the assembly instructions. If you do not assemble the EFX according to these guidelines, you could void the Precor � ½-inch socket wrench with extension Limited Warranty. � ⁹⁄₁₆-inch socket wrench � ½-inch open end wrench �Crescent wrench Obtaining Service � Wire cutter You should not attempt to service the EFX except for maintenance tasks described in the owner’s manual. Shoul
ページ4に含まれる内容の要旨
� Open the box and assemble the components in the sequence Installation Requirements presented in this guide. Follow these installation requirements when assembling the unit: � Obtain assistance. Ask another capable adult for assistance during the assembly process. � Assemble the unit near the location where you plan to use it because it is heavy. � Use your fingers or the appropriate tools to insert fasteners. Proper alignment helps alleviate cross-threading. Do not fully wrench � Provide a
ページ5に含まれる内容の要旨
Hardware Kit (not shown to scale) Fasteners Quantity (A) Hex head screws (¾-inch) 16 (B) Flat washers (⁵⁄₁₆-inch) 16 (C) Buttonhead screws (2¾-inch) 2 (D) Flat washers (³⁄₈-inch) 2 (E) Split washers (⁵⁄₁₆-inch) 16 (F) Phillips-head cap screws (¾-inch) 3 (G) Locknuts (³⁄₈-inch) 2 (H) Joint connector screws 2 (J) Joint connector nuts 2 536i Elliptical Fitness CrossTrainer Assembly Guide 3
ページ6に含まれる内容の要旨
Fasteners Quantity (K) Star washers (³⁄₈-inch) 2 (L) Buttonhead screws (⁷ ₈-inch) 10 Note: Since the hardware kit is used universally across several different product lines, extra fasteners remain once you complete this assembly. 2 — Levelers with hex nuts (M) 2 — Display covers (N) 2 — Clamps (O) Top Bottom 536i Elliptical Fitness CrossTrainer Assembly Guide 4
ページ7に含まれる内容の要旨
Assembly Steps Remove the packaging around the ramp support covers. Grasp the magazine rack at its base and slide it up and off the front ramp support cover. Set it aside. Use a long-handle ⁵⁄₃₂-inch hex key to remove the four fasteners that secure the front ramp support cover. Set the fasteners aside. A tab on each side of the front ramp support cover holds the front and back covers together. Gently squeeze the sides of the back covers to release the tabs. Remove the front ramp support
ページ8に含まれる内容の要旨
Install the front ramp support cover. Align the mounts and engage the side clips by pressing the front and back covers together. Insert the four fasteners set aside in step 2. Wrench tighten using the long-handle ⁵⁄₃₂-inch hex key. Attach the magazine rack. Align the tabs and apply downward pressure and lightly squeeze the magazine rack and back cover together. An audible click is heard when the magazine rack is secured properly. 536i Elliptical Fitness CrossTrainer Assembly Guide 6
ページ9に含まれる内容の要旨
CAUTION: Avoid cross-threading. Make sure the moving arm assembly is well-aligned with the pivot tube before wrench tightening. Any damage caused during installation is not covered by the Precor Limited Warranty. Attach one moving arm assembly at a time. Align and thread it carefully into the pivot tube. To secure it, use a ½-inch open end wrench and tighten the moving arm pivot joint. Guide the moving arm to its equilibrium point and let it rest there. Perform the same step for the oppo
ページ10に含まれる内容の要旨
Prepare the stabilizers for installation. Insert a clamp (O) into each stabilizer and secure it loosely with a buttonhead screw (L). Thread a leveler (K) onto each stabilizer. Note: Make sure the nut is fully threaded onto the leveler. Refer to the illustration. For easier access to the base mounts, lift the front of the EFX off the floor and place a wedge of packaging beneath its base. Ask your assistant to hold the stabilizer, which has the cable protruding from both ends, next to the m
ページ11に含まれる内容の要旨
Unwrap the lower board cable and remove any kinks. Feed the cable through the console bracket as shown in the illustration. Lower the console bracket between the stabilizers and rest the base of the bracket against the two bottom flanges. Align the six mounting holes. Start with the side mounts and insert the four hex head screws (A), with four split washers (E), and four flat washers (B). Finger tighten. Insert the two bottom hex head screws (A) with two split washers (E), and two flat wa
ページ12に含まれる内容の要旨
Connect the heart rate cable to the 4-prong receptacle on the electronics board. Connect the RJ45 cable to its receptacle on the back of the display console. An audible click is heard when the cable is properly attached. Place excess cable inside the console bracket. Important: When connecting the RJ45 cable to the back of the display, look for the receptacle that is in the same orientation as shown in the illustration below. Text embossed on the plastic states LOWER BOARD CONNECTION. Low
ページ13に含まれる内容の要旨
Remove the foam pouch from the ramp. Place the display covers (N) around the console bracket. Insert two buttonhead screws (L) and wrench tighten. Position the water bottle holder as shown in the illustration. Place Make sure the top cover’s front edge is flush with the display the top section over the handrail and align the two mounting console bracket before you secure it to the bottom cover. holes. Position the base below the handrail and align the slits and mounting pems with the top sect
ページ14に含まれる内容の要旨
Before exercising, make sure the EFX is level and does not Verify the heart rate display is operational. wobble from side to side. 1. Hold on to a stationary handrail and step on the foot pedals. Important: If the EFX is placed on a slightly uneven surface, 2. When you are comfortably situated, begin pedaling. A pedaling turning the levelers can help, but will not compensate for speed above 40 strides per minute must be maintained for extremely uneven surfaces. several seconds. 1. Remove th
ページ15に含まれる内容の要旨
ページ16に含まれる内容の要旨
Precor Incorporated 20031 142nd Avenue NE ©2011 Precor Incorporated P.O. Box 7202 www.precor.com Woodinville, WA USA 98072-4002 EFX536i AG 301736-101, en 1-800-347-4404 30 December 2011
ページ17に含まれる内容の要旨
User's Reference Manual ® EFX 536i ® EFX 532i Elliptical Fitness CrossTrainers
ページ18に含まれる内容の要旨
ページ19に含まれる内容の要旨
Important Safety Instructions Read all instructions in the documentation provided with your Make sure all users see a physician for a complete physical exercise equipment, including all assembly guides, user guides, examination before they begin any fitness program, particularly if and owner’s manuals, before installation of this device. they have high blood pressure, high cholesterol or heart disease; have a family history of any of the preceding The display apparatus (hereinafter refe
ページ20に含まれる内容の要旨
Care should be taken when mounting or dismounting the When using the treadmill, always attach the safety clip to your equipment. clothing before beginning your workout. Failure to use the safety clip may pose a greater risk of injury in the event of a fall. Read, understand, and test the emergency stop procedures before use. Keep in mind that heart rate monitors are not medical devices. Various factors, including the user’s movement, may affect the Keep the power cord or option
