ページ1に含まれる内容の要旨
MD200
INSTALLATION/OWNER'S MANUAL
AM/FM/CD Marine Receiver
Charge Port
ページ2に含まれる内容の要旨
MD200 INSTALLATION Preparation Please read entire manual before installation. Before You Start • Disconnect negative battery terminal. Consult a qualified technician for instructions. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Remove 2 transit screws located on top of the unit. • Insert
ページ3に含まれる内容の要旨
MD200 INSTALLATION Wiring Diagram Rear Preamp Output Connect to amplifier RCA input RCA Cable (sold separately) Antenna Connector BLUE Remote Turn-On Connect to amplifier or power AMP antenna. Insulate wire if not used. BLACK Ground Connect to vehicle chassis ground. RED Accessory Connect to ignition circuit or switched 12 volt source. 5 AMP AGC Fuse YELLOW Memory Connect to battery circuit or constant 12 volt source. FUSE When replacing the fuse, make sure new fuse is the Right Fr
ページ4に含まれる内容の要旨
MD200 OPERATION Control Locations 7 8 1 2 3 4 5 6 18 17 16 15 14 13 12 11 10 9 Release Preset 6 1 10 Volume Knob Preset 5 2 11 Mute / Power Preset 4 / Play / Pause 3 12 Tune / Track Down Preset 3 / Intro 4 13 Tune / Track Up Preset 2 / Random 5 14 Source Preset 1 / Repeat 6 15 Eject Band 7 16 8 USB Charging Port 17 Display 9 Auxiliary Input Audio / Menu 18 The MD200 has an easy-to-use interface that provides a rewarding experience, as well as support for your favo
ページ5に含まれる内容の要旨
MD200 OPERATION Control Locations - Remote 1 2 3 4 5 9 6 8 7 Display 1 Volume Down 6 Volume Up 2 Audio / Menu 7 Power / Mute 3 Band 8 Source 4 Tune / Track Down 9 Tune / Track Up 5 5
ページ6に含まれる内容の要旨
MD200 OPERATION General Operation Faceplate Removal Press RELEASE and pull away from the left side to remove. To re-install, insert right side of faceplate first then push left side to secure. Semi-permanent Remove trim ring and install supplied #1 x 7/32” Phillips Faceplate Installation head screw through left side of mounting frame into faceplate. Power On/Off Press to turn the unit on. Inserting a CD will turn the unit on automati
ページ7に含まれる内容の要旨
MD200 OPERATION General Operation Press and hold AUDIO/MENU for more than 3 seconds to Setup Menu access the setup menu, then press AUDIO/MENU to cycle through menu options. When desired option appears in the display, rotate the volume knob left/right to adjust or activate the desired function. Menu Function Options Action LOUD OFF Disables the loudness function. Loudness Enables the loudness function. Activating this feature Curve LOUD ON wil
ページ8に含まれる内容の要旨
MD200 OPERATION Audio Operation Bass Press AUDIO until BAS appears. Rotate the volume knob left/right to adjust. (-6 minimum / 6 maximum) Treble Press AUDIO until TRE appears. Rotate the volume knob left/right to adjust. (-6 minimum / 6 maximum) Balance Press AUDIO until BAL appears. Rotate the volume knob left/right to adjust. (L12 - R12) "BAL R=L" represents equal balance. Fader Press AUDIO until FAD appears. Rotate the volume knob left/right t
ページ9に含まれる内容の要旨
MD200 OPERATION CD Player Operation Insert CD With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. Eject CD Press the EJECT button to stop and eject the CD. The unit will change to tuner mode. Track Select Press TRACK to skip to the beginning of the next track. ll Press TRACK to return to the beginning of the current nn track. Pressing TRACK again skips to the beg
ページ10に含まれる内容の要旨
MD200 OPERATION Limited One Year Warranty This warranty gives you specific legal What to do? rights. You may also have other rights 1. Before you call for service, check the which vary from state to state. troubleshooting guide in your owner’s manual. A slight adjustment of any Dual Electronics Corp. warrants this custom controls may save you a service product to the original purchaser to be free call. from defects in mater
ページ11に含まれる内容の要旨
MD200 OPERATION Troubleshooting Problem Cause Action Yellow wire not connected or incorrect voltage Check connections for proper voltage Red wire not connected or incorrect voltage (11~16VDC) Unit will not turn on (no power) Black wire not connected Check connection to ground Fuse blown Replace fuse Speaker wires not connected Check connections at speakers Unit has power One or more speaker wires touching each Insulate all bare speaker wi
ページ12に含まれる内容の要旨
Specifications CD Player Frequency response: 20Hz-20kHz Channel separation @ 1kHz: >65dB D/A converter: 1 Bit FM Tuner Tuning range: 87.5MHz-107.9MHz Usable sensitivity: 12dBf 50dB quieting sensitivity: 16dBf Stereo separation @ 1kHz: 40dB Frequency response: 30Hz-13kHz AM Tuner Tuning range: 530kHz-1710kHz Usable sensitivity: 30uV Frequency response: 80Hz-2kHz General Speaker output impedance: 4~8 ohms Fuse: 5 amp AGC Dimensions: 7" x 7
