ページ1に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page A (1,1)
INSTRUCTION MANUAL
VHF TRANSCEIVER
iF14/S
UHF TRANSCEIVER
iF24/S
This device complies with Part 15 of the FCC
rules. Operation is subject to the condition that
this device does not cause harmful interfer-
ence.
ページ2に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page i (1,1) SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic energy • DO NOT operate the radio without a proper antenna attached, as this during transmit mode. This radio is designed for and clas- may damaged the radio and may also cause you to exceed FCC RF sified as “Occupational Use Only”, meaning it must be exposure limits. A proper antenna is the antenna supplied with this used only during the course of employment by individuals ra
ページ3に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page iii (1,1) FOREWORD PRECAUTION READ ALL INSTRUCTIONS carefully and completely before R WARNING! NEVER hold the transceiver so that the antenna using the transceiver. is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform SAVE THIS INSTRUCTION MANUAL— This instruction best if the microphone is 5 to 10 cm (2 to 4 inches) away from the manual contains important operating instructio
ページ4に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page v (1,1) ACCESSORIES 1 Supplied accessories 1 TABLE OF CONTENTS The following accessories are supplied: Qty. SAFETY TRAINING INFORMATION …………………………………… i q Flexible antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 FOREWORD ……………………………………………………………… iii w Battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 EXPLICIT DEFINITIONS ………………………………………………… iii OPERATING NOTES ……………………………………………………
ページ5に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 2 (1,1) 1 ACCESSORIES ACCESSORIES 1 Accessory attachments 1 D Flexible antenna ï Battery pack Connect the supplied flexible an- To attach the battery pack: tenna to the antenna connector. Slide the battery pack on the back of the transceiver in the direc- tion of the arrow (q), then lock it with the battery release button. CAUTION: • Slide the battery pack until the battery release button makes a ‘click’ • NEVER HOLD by the antenna sound. when carrying t
ページ6に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 4 (1,1) 1 ACCESSORIES ACCESSORIES 1 ï Jack cover D Belt clip 1 Attach the jack cover when the optional speaker-microphone is not To attach the belt clip: used. q Release the battery pack if it is attached. To attach the jack cover: To detach the jack cover: w Slide the belt clip in the direction of the arrow until the belt clip is q Attach the jack cover to the q Unscrew the screws with a locked and makes a ‘click’ sound. [SP MIC] connector. phillips screw
ページ7に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 6 (1,1) 2 PANEL DESCRIPTION PANEL DESCRIPTION 2 Front, top and side panels 2 e LED INDICATOR (p. 8) q IC-F14S/F24S IC-F14/F24 ➥ Lights red while transmitting. ➥ Lights green while receiving a signal, or when the squelch is open. ➥ Lights/blinks orange when the matched 2/5-tone code is re- ceived, according to the pre-programming. r SPEAKER-MICROPHONE CONNECTOR [SP MIC] Connects the optional speaker-microphone. (p. 31) w i e u [SP MIC] jack cover Speaker
ページ8に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 8 (1,1) 2 PANEL DESCRIPTION PANEL DESCRIPTION 2 ‘ ‘ LED indicator ‘ ‘ Programmable function keys The LED indicator indicates several informa- The following functions can be assigned to [Upper] and [Lower] 2 tion as follows; programmable function keys. (Ref.; R=Red, G=Green, O=Orange) Consult your Icom dealer or system operator for details concerning your transceivers programming. If the programmable function names are bracketed in the following explanation
ページ9に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 10 (1,1) 2 PANEL DESCRIPTION PANEL DESCRIPTION 2 MONITOR KEY DTMF AUTODIAL KEY ➥ Mute and release the CTCSS (DTCS) or 2-tone squelch mute. Push to transmit the programmed DTMF code. Open any squelch/deactivate any mute while pushing this key. 2 CALL KEYS (LMR operation only) Push to transmit a 2/5-tone code. ➥ Activates one of (or two of) the following functions on each chan- • Call transmission is necessary before you call another station de- nel independ
ページ10に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 12 (1,1) 3 CONVENTIONAL OPERATION CONVENTIONAL OPERATION 3 Turning power ON Call procedure ➥ Rotate [VOL] to turn power ON. When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice trans- [VOL] 3 mission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX c
ページ11に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 14 (1,1) 3 CONVENTIONAL OPERATION CONVENTIONAL OPERATION 3 Receiving and transmitting NOTE: Transmitting without an antenna may damage the trans- D Transmitting notes ceiver. See p. 2 for antenna attachment. • Transmit inhibit function 3 The transceiver has several inhibit functions which restrict trans- Receiving: mission under the following conditions: q Rotate [VOL] to turn power ON. - The channel is in mute condition. w Toggle [CHANNEL SWITCH] (IC-F1
ページ12に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 16 (1,1) 3 CONVENTIONAL OPERATION CONVENTIONAL OPERATION 3 Scrambler function Man Down Emergency Call The optional voice scrambler units UT-109 (#01) and UT-110 (#01) The man down emergency call function transmits an emergency provide high performance private communication between stations call automatically, after the transceiver laying down in a horizontal 3 with the same scrambler codes. position for a pre-set time period. (The optional UT-113 MAN D
ページ13に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 18 (1,1) OPTIONAL UNIT INSTALLATION 4 OPTIONAL UNIT INSTALLATION 4 Optional unit installation Scrambler unit installation Install the optional unit as follows: The following PC board modification is required when installing the q Rotate [VOL] to turn the power OFF, and remove the battery optional UT-109 or UT-110. pack. (p. 3) q Rotate [VOL] to turn the power OFF, and remove the battery w Remove the unit cover. pack. (p. 3) 4 NOTE: Use a flat head screw
ページ14に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 20 (1,1) 5 BATTERY CHARGING BATTERY CHARGING 5 Battery charging Caution Prior to using the transceiver for the first time, the battery pack must R DANGER Charge the specified Icom batteries only. be fully charged for optimum life and operation. Only tested and approved for use with genuine Icom batteries. Fire and/or explosion may occur when a third party battery pack or CAUTION: To avoid damage to the transceiver, turn it OFF while counterfeit product i
ページ15に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 22 (1,1) 5 BATTERY CHARGING BATTERY CHARGING 5 Optional battery chargers D Rapid charging with the BC-160 ï AD-106 installation The optional BC-160 provides rapid charging of optional Li-Ion bat- q Install the AD-106 desktop charger adapter into the holder space tery packs. of the BC-119N/121N. • An AC adapter (may be supplied with BC-160 depending on ver- Desktop charger adapter sion) or the DC power cable (OPC-515L/CP-17L) is additionally Connectors 5
ページ16に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 24 (1,1) 5 BATTERY CHARGING BATTERY CHARGING 5 D Rapid charging with the BC-119N+AD-106 D Rapid charging with the BC-121N+AD-106 The optional BC-119N provides rapid charging of optional Li-Ion The optional BC-121N allows up to 6 battery packs to be charged battery packs. simultaneously. The following items are additionally required. The following items are additionally required: • Six AD-106. • One AD-106 (purchase separately). • An AC adapter (BC-124) or
ページ17に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 26 (1,1) 6 SWIVEL BELT CLIP SWIVEL BELT CLIP 6 e Clip the belt clip to a part of your belt. And insert the transceiver MB-93 contents into the belt clip until the base clip inserted fully into the groove. Qty. q Belt clip …………………………………………………………… 1 w Base clip …………………………………………………………… 1 q w 6 To attach r Once the transceiver is locked in place, it swivels as illustrated q Release the battery pack if it is attached. (p. 3) below. w Slide the base clip in
ページ18に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 28 (1,1) 6 SWIVEL BELT CLIP SWIVEL BELT CLIP 6 To detach q Turn the transceiver upside down in the direction of the arrow w Release the battery pack if it is attached. (p. 3) and pull out from the belt clip. e Pinch the clip (q), and slide the base clip in the direction of the arrow (w). q w 6 CAUTION: HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP. Otherwise the transceiver may not be attached to the holder or
ページ19に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 30 (1,1) 7 OPTIONS OPTIONS 7 D BATTERY PACK D BELT CLIPS • BP-230 Li-Ion BATTERY PACK • MB-93 SWIVEL BELT CLIP 7.4 V/800 mAh Li-Ion battery pack, allows approx. 5.5 hours* op- • MB-94 BELT CLIP eration. Exclusive alligator-type belt clip. The same as supplied with the • BP-231 Li-Ion BATTERY PACK transceiver. 7.4 V/1150 mAh Li-Ion battery pack, allows approx. 8 hours* op- • MB-96*/96F LEATHER BELT HANGER eration. The same as supplied with the transceiver.
ページ20に含まれる内容の要旨
IC-F14_F24-2.qxd 04.7.22 0:57 PM Page 32 (1,1) MEMO MEMO
