ページ1に含まれる内容の要旨
PARTS AND OPERATION MANUAL
PLASTER/MORTAR MIXERS
EM-700S
EM-700P
Revision #8 (03/17/06)
MULTIQUIP INC. . . . . PARTS DEPARTMENT:
18910 WILMINGTON AVE. 800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700 SERVICE DEPARTMENT:
800-421-1244 800-478-1244
FAX: 310-537-3927 FAX: 310-537-4259
E-mail:mq@multiquip.com � www:multiquip.com
© COPYRIGHT 2001, MULTIQUIP INC.
ページ2に含まれる内容の要旨
PAGE 2 — ESSICK EM-700S & 700P — PARTS & OPERATION MANUAL — REV. #8 (03/17/06)
ページ3に含まれる内容の要旨
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 ESSICK EM-700S & 700P — PARTS & OPERATION MANUAL — REV. #8 (03/17/08) — PAGE 3
ページ4に含まれる内容の要旨
TABLE OF CONTENTS Here's How To Get Help .......................................... 3 Table Of Contents ................................................... 4 Parts Ordering Procedures ..................................... 5 Rules for Safe Operation & Safety Decals .............. 6 Warranty .................................................................. 7 ESSICK — 700S & 700P Operations ......................................................... 8-11 Specifications ..............................
ページ5に含まれる内容の要旨
st Effective: June 1 , 2005 PARTS ORDERING PROCEDURES Ordering parts has never been easier! Choose from three easy options: Best Deal! Order via Internet (Dealers Only): If you have an MQ Account, to obtain a Order parts on-line using Multiquip’s SmartEquip website! Username and Password, E-mail us at: parts@multiquip.com. ■ View Parts Diagrams To obtain an MQ Account, contact your ■ Order Parts District Sales Manager for more information. ■ Print Specification Information Use the internet and q
ページ6に含まれる内容の要旨
RULES FOR SAFE OPERATION & SAFETY DECALS ■ Do not operate or service this equipment ■ When towing, an adequate safety chain before reading the operating and must be fastened to the frame, refer to page 9. maintenance instructions manual or serious ■ Keep all inexperienced and unauthorized injury may result. people away from the equipment at all times. ■ Do not operate this equipment unless all ■ Unauthorized equipment modifications will guards and safety devices are attached and void all warrant
ページ7に含まれる内容の要旨
WARRANTY There are no warranties, express or implied, made by Multiquip There are no warranties, express or implied, in addition to the Inc. hereunder on Products manufactured or distributed by it above except as may be provided in writing by Multiquip Inc. except the warranty against defects in material and workmanship MULTIQUIP INC. SHALL NOT BE LIABLE FOR ANY SPECIAL, on new Products to the original purchaser, as hereinafter set INDIRECT OR CONSEQUENTIAL DAMAGES. forth. THE FOREGOING WARRANTI
ページ8に含まれる内容の要旨
EM-700S & 700P — OPERATIONS CONTROLS KILL SWITCH: (Gasoline Engine Only) Located on the side of the engine cover. ENGINE THROTTLE AND CHOKE CONTROLS: Please refer to the engine owners manual for specific instructions. The electric motor switch ( electric motor only) located on the motor — is used to start and stop the mixer. DUMP LATCH: To dump the tub, grasp the dump handle and lift the dump latch, then rotate the tub to discharge the mix. After, discharge, return the tub to the vertical mixing
ページ9に含まれる内容の要旨
EM-700S & 700P — OPERATIONS PADDLE SHAFT BEARING IMPORTANT — DRUM HEAD SEAL CARE The paddle shaft in the Essick Mixer rotates in sealed ball On each end of the mixing drum is a drum head containing self bearings requiring no additional lubrication. adjusting paddle shaft seals. These seals consist of packing rings, split glands and spring actuated adjusters. A properly maintained seal prevents material from working around the BEARING BRACKET paddle shaft, causing excessive wear. The following is
ページ10に含まれる内容の要旨
EM-700S & 700P — OPERATIONS their hands in the mixing drum. STEP 1 TOWING — Before towing, check with local and state laws for proper compliance. The tow bar and chain must be properly attached to the mixer DRAW BAR and towing vehicle prior to towing. Refer to the following installation instruction: Step 1. Insert the Draw Bar into the main frame. Secure, utilizing BOLT & NUT the ¾" bolt (grade 5) and nylock nut. Tighten to 100 foot pounds. Step 2. Install the chain through the hole located betw
ページ11に含まれる内容の要旨
EM-700S & 700P — OPERATIONS CLEANING — BLADE ADJUSTMENTS END SCRAPER END SCRAPER END SCRAPER END SCRAPER END SCRAPER Always disconnect the spark plug wire before cleaning the inside of the drum. Never pour or spray water over the gasoline engine or electric motor. For consistent performance, long life and high quality mixing, thoroughly clean the mixer inside and out at the end of each day’s operation. To prevent lumps of dried mortar from forming and contamination of future batches, do not allo
ページ12に含まれる内容の要旨
EM-700S & 700P — SPECIFICATIONS EM-700S SPECIFICATIONS MODEL U.S.(inch) METRIC CAPACITY ....................................................7 CUBIC FEET ....................................................... 198 LITERS BAG CAPACITY .............................................1½ - 2½ ............................................................ 1½ - 2½ WEIGHT (appROX.) ......................................792 LBS. ............................................................. 357 KG. L X W X H .
ページ13に含まれる内容の要旨
NOTE PAGE ESSICK EM-700S & 700P — PARTS & OPERATION MANUAL — REV. #8 (03/17/08) — PAGE 13
ページ14に含まれる内容の要旨
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Section 1: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant. Section 2: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a ser
ページ15に含まれる内容の要旨
EM-700S & 700P — SUGGESTED SPARE PARTS EM-700S/P EM-700S/P 1 to 4 Units 5+ Units Qty. P/N Description Qty. P/N Description 3 ......... EM505834 ........... V-BELT 5 ......... EM505834 ........ V-BELT 3 ......... EM507846 ........... V-BELT, w/ELECTRIC MOTOR 5 ......... EM507846 ........ V-BELT, w/ELECTRIC MOTOR 6 ......... 491010 ................ LATCH ASSY 10 ....... 491010 ............. LATCH ASSY 3 ......... EM203010 ........... BLADE KIT STEEL DRUM 5 ......... EM203010 ........ BLADE KIT (70
ページ16に含まれる内容の要旨
EM-700S & 700P — DRUM HEAD AND PADDLE SHAFT ASSY DRUM HEAD PADDLE SHAFT ASSEMBLY 27 26 25 28 TOW END PAGE 16 — ESSICK EM-700S & 700P — PARTS & OPERATION MANUAL — REV. #8 (03/17/06)
ページ17に含まれる内容の要旨
EM-700S & 700P — DRUM HEAD AND PADDLE SHAFT ASSY DRUM HEAD AND PADDLE SHAFT ASSY DRUM HEAD PARTS NO. PART NO. PART NAME QTY. REMARKS 1 EM507274 PADDLE SHAFT 1 2 EM200297 U-BOLT 2 EM968011 NUT HEX ½-13 4 3 EM200292 U-BOLT INSERT 4 4 EM200018 COLLAR 1 5 EM902153 BEARING 2 6 EM507720 DUMP BEARING .................................................................... 2 ................ FROM S/N 98624071 6 500076 DUMP BEARING .................................................................... 2 ......
ページ18に含まれる内容の要旨
EM-700S — STEEL DRUM STEEL DRUM 109 110 111 108 PAGE 18 — ESSICK EM-700S & 700P — PARTS & OPERATION MANUAL — REV. #8 (03/17/06)
ページ19に含まれる内容の要旨
EM-700S — STEEL DRUM STEEL DRUM NO. PART NO. PART NAME QTY. REMARKS 100 EM201537 DUMP HANDLE 1 * 101 EPC-1 TOWING TONGUE (P. EYE) ................................... 1 .............. NO LONGER AVAILABLE 101 EBC-1 TOWING TONGUE (PIN HOLE) ............................. 1 .............. CONTACT MQ SALES DEPT./ACCESSORY ITEM 101 HBC-1 TOWING TONGUE (BALL HITCH) ......................... 1 .............. CONTACT MQ SALES DEPT./ACCESSORY ITEM 102 EM963580 CAP SCREW ....................................
ページ20に含まれる内容の要旨
EM-700P — POLYETHYLENE DRUM POLYETHYLENE DRUM 122 123 124 125 126 127 124 125 128 129 PAGE 20 — ESSICK EM-700S & 700P — PARTS & OPERATION MANUAL — REV. #8 (03/17/06)
