ページ1に含まれる内容の要旨
PARTS AND OPERATION MANUAL
STOW VIBRATOR HEADS
MODELS 900, 1000, 1300,
1400, 1700, 2100 & 2600
MODEL #
SERIAL #
Revision #1 (04/22/02)
STOW CONSTRUCTION EQUIPMENT STOW CONSTRUCTION EQUIPMENT STOW CONSTRUCTION EQUIPMENT STOW CONSTRUCTION EQUIPMENT STOW CONSTRUCTION EQUIPMENT PARTS DEPARTMENT:
A DIVISION OF MULTIQUIP INC. 800-427-1244
POST OFFICE BOX 6254 FAX: 800-672-7877
CARSON, CA 90749
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
310-537-3700 • 888-252-STOW [888-252-7869]
800-478-1244
FAX: 310-53
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 VIBRATOR HEADS — PARTS & OPERATION MANUAL — REV. #1 (04/22/02) — PAGE 3
ページ4に含まれる内容の要旨
VIBRATOR HEADS— TABLE OF CONTENTS Here's How To Get Help ............................................ 3 Table Of Contents ..................................................... 4 Parts Ordering Procedures ....................................... 5 Safety Message Alert Symbols ................................. 6 Rules For Safe Operation ......................................... 7 MQ STOW - VIBRATOR HEADS Preparation & Operation ........................................... 8 Maintenance ............
ページ5に含まれる内容の要旨
VIBRATOR HEADS— PARTS ORDERING PROCEDURES n Dealer account number n Dealer name and address n Shipping address (if different than billing address) n Return fax number n Applicable model number n Quantity, part number and description of each part n Specify preferred method of shipment: UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* Airborne Express* Truck or parcel post *Normally shipped
ページ6に含まれる内容の要旨
VIBRATOR HEADS— SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! HAZARD SYMBOLS Engine exhaust gases contain poisonous Safety precautions should be followed at all times when operating carbon monoxide. This gas is colorless and this equipment. Failure to read and understand the Safety odorless, and can cause death if inhaled. Messages and Operating Instructions could result in injury to NEVER operate this equipment in a confined yourself and others. area or enclosed str
ページ7に含まれる内容の要旨
VIBRATOR HEADS— RULES FOR SAFE OPERATION WARNING: ALWAYS check the equipment for loosened threads or bolts before starting. Failure to follow instructions in this manual may NEVER use accessories or attachments, which are not lead to serious injury or even death! This recommended by Stow for this equipment. Damage to the equipment is to be operated by trained and equipment and/or injury to user may result. qualified personnel only! This equipment is for industrial use only. EMERGENCIES T
ページ8に含まれる内容の要旨
VIBRATOR HEADS—PREPARATION & OPERATION This safety alert symbol is used to attract your WARNING! WARNING! WARNING! WARNING! WARNING! attention. Personal safety is involved. When you see this symbol, become alert; heed its MAKE CERTAIN the motor is disconnected message. from the power source and the switch is in the "OFF" position. WARNING! WARNING! WARNING! WARNING! WARNING! 4. When connecting the head to the casing, clean the mating DO NOT attempt to operate this vibrator head threads with a
ページ9に含まれる内容の要旨
VIBRATOR HEADS— MAINTENANCE MAINTENANCE Figure 3. Head Parts Reference CAUTION! CAUTION! CAUTION! CAUTION! CAUTION! Number Description DO NOT allow the vibrator head to wear below 1 ....................... Housing the following dimensions: See General 2 ....................... Nut or Screw Specifications - page11. 3 ....................... Bearing The vibrator heads should be inspected and lubricated after 4 ....................... Spindle every 100 hours of use. Refer to (Figure 3). 5 .....
ページ10に含まれる内容の要旨
VIBRATOR HEADS — MAINTENANCE 4. Remove the cap screw or hex nut that holds the lower 6. Apply a high strength anaerobic sealant to the external bearings in place. (Ref. 2) threads of the casing adapter. Screw the adapter into the housing and tighten. Threads are left-hand. (Ref. 1,9) 5. Remove the spindle with the upper bearings still attached. The lower bearings (tip-end) can now be removed from 7. Tip head over and pour in the required amount of Stow the housing.(Ref. 4) Lube P/N 12000-30
ページ11に含まれる内容の要旨
VIBRATOR HEADS — SPECIFICATIONS SPECIFICATIONS TABLE 3. GENERAL SPECIFICATIONS Model 900 1000 1300 1400 1700 2100 2600 1 lb. 2 lb. 4 lbs. 4 lbs. 6 lbs. 8 lbs. 12 lbs. Weight 11 oz. 6 oz. 11 oz. 10 oz. 4 oz. 11 oz. 10 oz. Length 15" 14" 15" 15" 14" 13" 13" Manufacturing Diameter 7/8 1 - 1/16 1 - 3/8 1 - 3/8 1 - 11/16 2 - 1/8 2 - 5/8 Minimum Wear Diameter 13/16 1 1 - 1/4 1 - 1/4 1 - 9/16 1 - 7/8 2 - 1/4 Head Lube Capacity 1/2 oz. 1/2 oz. 1/2 oz. 1/2 oz. 3/4 oz. 1 oz. 1 - 1/2 oz. VIBRATOR HEADS
ページ12に含まれる内容の要旨
VIBRATOR HEADS — SEAL INSTALLATION SEAL INSTALLATION SHAFT END HEAD END 2. Seal lip to face vibrator head end. 1. Seal lip to face vibrator shaft end. Figure 4. Seal Installation Seal outer case to face outer case of first seal pressed into casing adapter. Depending on vibrator head model, casing adapter may not appear exactly as shown. CAUTION! CAUTION! CAUTION! CAUTION! CAUTION! Improper seal installation may cause premature head failure. PAGE 12 — VIBRATOR HEADS— PARTS & OPERATION M
ページ13に含まれる内容の要旨
NOTE PAGE VIBRATOR HEADS — PARTS & OPERATION MANUAL — REV. #1 (04/22/02) — PAGE 13
ページ14に含まれる内容の要旨
SV-SERIES — VIBRATOR HEAD ASSY. VIBRATOR HEAD ASSY. PAGE 14 — VIBRATOR HEADS— PARTS & OPERATION MANUAL — REV. #1 (04/22/02)
ページ15に含まれる内容の要旨
SV-SERIES — VIBRATOR HEAD ASSY. VIBRATOR HEAD ASSY. ITEM NO. PART NO. DESCRIPTION 900 1000 1300 1400 1700 2100 2600 - 17302-505 MODEL 900 X - X 16369-501 MODEL 1000 - MODEL 1300 X 16317-501 - 16316-501 MODEL 1400 X - X 15699-505 MODEL 1700 - MODEL 2100 X 16301-501 - 16274-501 MODEL 2600 X 1 1 17303-002 HOUSING 1 HOUSING 1 16371-001 1 16320-001 HOUSING 1 1 1 1 15700-001 HOUSING 1 HOUSING 1 16305-001 1 16279-001 HOUSING 1 2 1 08233-004 NUT GRIPCO 1/4-20 2 08233-005 NUT GRIPCO 5/16-18 1 2 08297-00
ページ16に含まれる内容の要旨
SV-SERIES — VIBRATOR HEAD ASSY. VIBRATOR HEAD ASSY. PAGE 16 — VIBRATOR HEADS— PARTS & OPERATION MANUAL — REV. #1 (04/22/02)
ページ17に含まれる内容の要旨
SV-SERIES — VIBRATOR HEAD ASSY. VIBRATOR HEAD ASSY. ITEM NO. PART NO. DESCRIPTION 900 1000 1300 1400 1700 2100 2600 5 07001-056 SEAL 2 5 2 07001-021 SEAL 5 07001-029 SEAL 2 2 5 2 07001-046 SEAL 5 SEAL 2 07001-057 5 2 07001-019 SEAL 6 26055-001 SPACER 1 8 26050-001 FITTING ADAPTER 1 8 16375-001 FITTING ADAPTER 1 8 16328-001 FITTING ADAPTER 1 8 1 16327-001 FITTING ADAPTER 9 CASING ADAPTER 1 26049-001 9 16374-002 CASING ADAPTER 1 9 1 16325-001 CASING ADAPTER 9 16326-001 CASING ADAPTER 1 9 1 16704-
ページ18に含まれる内容の要旨
TERMS AND CONDITIONS OF SALE Effective: July 1, 2000 PAYMENT TERMS 4. Freight is at the sender’s expense. All PRICING AND REBATES parts must be returned freight prepaid to Terms of payment for parts are net 10 days. Prices are subject to change without prior Multiquip’s designated receiving point. notice. Price changes are effective on a specific date and all orders received on or after that date 5. Parts must be in new and resalable FREIGHT POLICY condition, in the original Multiquip package w
ページ19に含まれる内容の要旨
NOTE PAGE VIBRATOR HEADS — PARTS & OPERATION MANUAL — REV. #1 (04/22/02) — PAGE 19
ページ20に含まれる内容の要旨
PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 STOW CONSTRUCTION EQUIPMENT STOW CONSTRUCTION EQUIPMENT STOW CONSTRUCTION EQUIPMENT STOW CONSTRUCTIO
