ページ1に含まれる内容の要旨
USER
MANUAL
MODEL 1069
OnSite™ VDSL2 CPE
REGULATORY MODEL NUMBER:
03342D4-001
This is a Class A device and is not intended for
use in a residential environment.
Part# 07M1069-UM SALES OFFICE
Rev. A
(301) 975-1000
Revised 12/21/11
TECHNICAL SUPPORT
(301) 975-1007
An ISO-9001Certified
Company
ページ2に含まれる内容の要旨
CONTENTS 1.0 Warranty Information ................................................................. 3 1.1 Regulatory Information ................................................................. 3 EMC Directive:.............................................................................. 3 Low-Voltage Direcive (Safety):..................................................... 3 PSTN:........................................................................................... 3 1.2 Radio and TV Interf
ページ3に含まれる内容の要旨
1.0 WARRANTY INFORMATION Patton Electronics warrants all Model 1069 components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the first date of the shipment. This warranty is limited to defects in workmanship or materials, and does not cover customer damage, abuse or unauthorized modification. If this product fails or does not performs as warranted, your sole recourse shall be repair or replacement as described above. Under
ページ4に含まれる内容の要旨
of Part 15 of FCC rules, which are designed to provide reasonable pro- tection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular instal- lation. If the device does cause interference to radio or television recep- tion, which can be determined by disconnecting the unit, the user is encouraged to try to correct the interference by one or more of the follow- ing measures: moving the computing equipment away from th
ページ5に含まれる内容の要旨
1.6 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. This device can only be repaired by qualified service per- sonnel. • Do not open the device when the power cord is con- nected. For systems without a power switch and without an external power adapter, line voltages are present within the device when the power cord is connected. • For devices with an external power adapter, the power adapter shall be a listed Limited Power Source. The mains outlet t
ページ6に含まれる内容の要旨
In accordance with the requirements of council direc- tive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you sepa- rate this product from other waste and scrap and deliver to the WEEE collection system in your country for recy- cling. This device contains no user serviceable parts. This device can only be repaired by qualified service per- sonnel. WARNING This device is NOT intended nor approved for connec- tion to the PSTN. It is intended only
ページ7に含まれる内容の要旨
2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics Technical Support at +1 (301) 975-1007. 2.1 FEATURES VDSL2 - Easy to configure Auto-MDIX Ethernet Configurable 10/100, Full/Half, and Auto-Negotiating Ethernet Extends up to 4x 10/100Base
ページ8に含まれる内容の要旨
POTS/ISDN twisted-pair RJ-45 interface VDSL twisted-pair RJ-45 interface Ethernet ports (0-3) Reset switch Power jack Figure 1. Model 1069 rear panel 2.3 APPLICATION In an example application, the VDSL2 CPE modem is placed in either MxU environments or individual residents for delivering triple play ser- vices including “fiber like” high-speed broadband service. Built-in POTS/ISDN splitters allow for both data and voice to be broken out at the CPE. Figure 2. Model 1069 and VDSL DSLAM appli
ページ9に含まれる内容の要旨
3.0 INSTALLATION The Interconnecting cables shall be acceptable for external use and shall be rated for the proper applica- tion with respect to voltage, current, anticipated tem- CAUTION perature, flammability, and mechanical serviceability. To connect the Model 1069, do the following: 1. Connect the Line port of the Model 1069 with a telephone cable (refer to section 3.1, “Connecting the Line Interface” on page 10). 2. Connect an Ethernet port to the network card of a PC via an Ether-
ページ10に含まれる内容の要旨
3.1 CONNECTING THE LINE INTERFACE The Interconnecting cables shall be acceptable for external use and shall be rated for the proper applica- tion with respect to voltage, current, anticipated tem- CAUTION perature, flammability, and mechanical serviceability. The Model 1069 supports communication over a distance of up to 10,000 ft (3 km) over 24 AWG (0.5 mm) twisted-pair wire or Cat5+. Note Actual distance and link performance may vary depending on the environment and type/gauge of wire used
ページ11に含まれる内容の要旨
3.2 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE The Interconnecting cables shall be acceptable for external use and shall be rated for the proper applica- tion with respect to voltage, current, anticipated tem- CAUTION perature, flammability, and mechanical serviceability. The RJ-45 ports labeled Ethernet are the Auto-MDIX10/100Base-T inter- face. These ports are designed to connect directly to a 10/100Base-T device or network. Figure 5 shows the signal/pin relationships on this interface
ページ12に含まれる内容の要旨
3.4 CONNECTING POWER The Interconnecting cables shall be acceptable for external use and shall be rated for the proper applica- tion with respect to voltage, current, anticipated tem- CAUTION perature, flammability, and mechanical serviceability. The Model 1069 does not have a power switch, so it powers up as soon as it is plugged in. An external AC or DC power supply is available separately. This connec- tion is made via the barrel jack on the rear panel of the Model 1069. No configuration
ページ13に含まれる内容の要旨
5.0 OPERATION Once the Model 1069 is properly installed, it should operate transpar- ently. No user settings required. This section describes reading the LED status monitors. Before applying power to the Model 1069, please review section 3.4, “Connecting Power” on page 12 to verify that the unit is connected to the appropriate power source. 5.1 FRONT PANEL LED STATUS MONITORS The Model 1069 features six front panel LEDs that monitor power, the Ethernet signals, the VDSL2 connection, and th
ページ14に含まれる内容の要旨
APPENDIX A SPECIFICATIONS A.1 VDSL2 Full compliance up to 30Mhz profile A.2 LAN CONNECTION Four RJ-45, 10/100Base-T, IEEE 802.3 Ethernet A.3 TRANSMISSION LINE Two-wire unconditioned twisted pair VDSL2 Connector: RJ-45 A.4 LED STATUS INDICATORS Power (Green) VDSL2: Link (Green) Local (Green) Remote (Green) Ethernet: Link (Green) & Activity (Flashing Green) A.5 POWER SUPPLY External AC and DC options: AC: 120 VAC, 220 VAC, and UI (120–240 VAC) DC: 12 VDC, 24 VDC and 48
ページ15に含まれる内容の要旨
APPENDIX B MODEL 1069 SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model # Description Base Models 1069/EUI OnSite VDSL2 CPE RJ45 Line, 100-240VAC 07M1069-UM User Manual Power Supplies PS-03671H1-002 100-240VAC (12V, DC/2A) Wall mount power adapter Power Adapters 12-130 European replacement plug 12-129 American replacement plug 12-131 United Kingdom plug 12-132 Australian/Chinese plug 15
ページ16に含まれる内容の要旨
APPENDIX C MODEL 1069 SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 Pin 1: TX+ Pin 2: TX- Pin 3: RX+ Pin 6: RX- Pins 4, 5, 7, 8: no connection C.2 VDSL2 INTERFACE RJ-45 Pin 4: RING Pin 5: TIP Pins 1, 2, 3, 6, 7, 8: no connection C.3 POTS/ISDN INTERFACE RJ-45 Pin 4: 2-wire RING Pin 5: 2-wire TIP Pins 1, 2, 3, 6, 7, 8: no connection Copyright © 2011. Patton Electronics Company All Rights Reserved. 16
