ページ1に含まれる内容の要旨
TD-W8951NB
150Mbps Wireless N ADSL2+ Modem Router
(Annex B)
Rev: 3.0.0
1910010747
ページ2に含まれる内容の要旨
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., L
ページ3に含まれる内容の要旨
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
ページ4に含まれる内容の要旨
CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device has been designed to operate with the antennas listed below, and having a maximum gain of 5dBi. Antennas not included in this list or having a gain greater than 5dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to
ページ5に含まれる内容の要旨
NCC Notice: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功 率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並 改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電 機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 Продукт сертифіковано згідно с пр авилами си стеми УкрСЕПРО на відп овідн іс ть вимогам нормативних документі в та вимогам, що пер е дбачені чинними законодавчими актами Украї н и. Safety Information When product has power button, the power button is one of the way to shut off the product; when th
ページ6に含まれる内容の要旨
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N ADSL2+ Modem Router (Annex B) Model No.: TD-W8951NB Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU The a
ページ7に含まれる内容の要旨
CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Introduction......................................................................................... 2 1.1 Product Overview........................................................................................... 2 1.2 Main Features ................................................................................................ 2 1.3 Conventions ..
ページ8に含まれる内容の要旨
4.5.4 UPnP.......................................................................................................................64 4.5.5 DDNS......................................................................................................................65 4.5.6 CWMP.....................................................................................................................66 4.6 Maintenance ......................................................................................
ページ9に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Package Contents The following contents should be found in your package: One TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) One Power Adapter for TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) Quick Installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter (Optional) One Resource CD, which includes this User Guide Note: Make sure that the package contains the above it
ページ10に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Chapter 1. Introduction Thank you for choosing the TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B). 1.1 Product Overview The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or IEEE 802.11n/ IEEE 802.11g/ IEEE 802.11b wireless network. The TD-W8951NB connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made us
ページ11に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Downstream data rates up to 24Mbps, upstream data rates up to 3.5Mbps （With Annex M enabled）. Supports long transfers, the max line length can reach to 6.5Km. Supports remote configurati on and management through SNMP and CWMP. Supports PPPoE, it allows connecting the internet on demand and disconnecting from the Internet when idle. Provides reliable ESD and surge-protect func tion with quick response semi-conduc
ページ12に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locate on the front panel. They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name Status Indication On The modem router is powered on. (Power) The modem router is off. Please ensure that the power adapter is Off connected correctly. On ADSL line is synchronized and ready to use. Fl
ページ13に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Note: 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Modem Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now. 2. If the Internet LED is off, please check your ADSL LED first. If your ADSL LED is also off, please ref
ページ14に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide least 5 seconds. And the Router will reboot to its factory default settings. Method two: Restore the default setting from “Maintenance-SysRestart” of the Router's Web-based Utility. WiFi: Press this button to enable or disable Wireless LAN interface. 1, 2, 3, 4 (LAN): Through the port, you can connect the Router to your PC or the other Ethernet network devices. ADSL: Through the port, you can connect the router wit
ページ15に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Figure 2-3 Wall-mount Install Note: The diameter of the screw, 3.5mm
ページ16に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide • PHONE: Connect to the phone sets • MODEM: Connect to the ADSL port of TD-W8951NB Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of TD-W8951NB. Connect the other end to the MODEM port of the external splitter. Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s Ethernet port or a regular hub/switch port, and the other end to the LAN port on the TD
ページ17に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-W8951NB or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Follow the steps below to configure it. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1). Figure 3-1 Step 2: Right
ページ18に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3 10
ページ19に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 Note: You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above. Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab,
ページ20に含まれる内容の要旨
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide Figure 3-5 If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Router. Figure 3-6 You can check it following the steps below: 1) Is the connection between your PC and the Router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the Router's IP
