ページ1に含まれる内容の要旨
PXDP
iPOD INTERFACE
Instruction Manual
PROFESSIONAL INSTALLATION
STRONGLY ADVISED
IMPORTANT NOTE
iPod Firmware MUST be updated BEFORE any other step is taken.
Otherwise, the iPod will not operate properly. See page 1 for further details.
Peripheral Electronics®,
a division of AAMP of America™
13160 56th Court Clearwater, Florida 33760
866-788-4237 in the US or 727-572-9255 ext.262 for international calls
support@peripheralelectronics.com
©2006 AAMP™ of Florida, Inc.
rm11.29.06
DIN CONNE
ページ2に含まれる内容の要旨
Table of Contents Pages CHAPTER 1-Getting Started 1.1 Introduction 1 1.2 Precautions 1 1.3 Configuration & Harnesses 2 1.4 Programming the PXDP 3 CHAPTER 2-General Installation 2.1 Installation Location 4 2.2 Pre-Installation Checklist 4 2.3 Wiring Connections 4-5 2.4 Installation at Changer Location 5-6 2.4 Installation at Radio 6 CHAPTER 3 -Operation 3.1 Operation 7 3.2 Troubleshooting 8 3.3 Warranty 9 3.4 Warn
ページ3に含まれる内容の要旨
Chapter 1- Getting Started 1.1 Introduction ® Thank you for purchasing the PXDP iPod Interface, by Peripheral Electronics . The PXDP is designed to provide endless hours of listening pleasure through most vehicles’ factory radios. To ensure that your iPod performs correctly in your car or truck, we recommend that you read this entire manual before attempting installation of the PXDP interface. The PXDP interface will allow you to connect your iPod to a factory radio that has the ability to
ページ4に含まれる内容の要旨
Docking cable Vehicle specific harness PXDP interface 1.3 Configuration and Harness Selection This section will instruct you on how to properly identify and/or confirm the proper interface dip-switch configuration and vehicle specific harness selection. Please go to: http://www.peripheralelectronics.com/apps Use this guide to locate your vehicle, inform you of the proper dip-switch configuration for the interface, and the vehicle specific harness that you will need for your particular vehic
ページ5に含まれる内容の要旨
1.6 Programming the PXDP Now that you have identified the correct harness and dip-switch configuration using the application guide, it is now time to program the interface. To program the interface, set the dip-switches located on the side of the interface (see Fig.1 below) to the congfiguration listed for your vehicle in the online applica- tion guide: http://www.peripheralelectronics.com/apps Switches are in their default setting of “off” in the up position and are turned “on” when switch
ページ6に含まれる内容の要旨
V O L P WR S E E K 1 2 3 4 R D S S T C U A N N E 5 6 D S P B A N D T D A I S P C E IN F O S T Y E P E K E T R A F A E U Q T O A V U O T I O Chapter 2- General Installation 2.1 Installation Location Most installations will require you to remove the factory radio in order to plug in the vehicle specific harness. Some vehicles may require you to connect the interface to a factory pre-run CD changer cable. The location of these CD changer cables will vary by vehicle. Some common locations of the
ページ7に含まれる内容の要旨
Make these connections only after verifying the proper circuit on your radio harness with a voltmeter. With the key OFF and the negative test lead of the voltmeter firmly touching a bare metal chassis part of your car, begin probing the wires in the main radio harness with the positive test lead. The constant 12V+ circuit should read a continuous 12 volts or higher. Once you’ve identified the constant 12V+ circuit, strip back about 1/8” of the insulation. Now take the positive test lead
ページ8に含まれる内容の要旨
4. Decide on a convenient location to mount your iPod. 5. Run the docking cable from the interface to the desired mounting location. Use caution to not cut, pinch, or crimp the cable during this step. Avoid moving parts, vehicle wiring harnesses and areas of excessive heat when routing the cable. 6. Secure the interface in the vehicle using; double sided tape, Velcro or wire ties. Make sure to check for proper clearance and avoid moving parts. Take into account the size of the interface an
ページ9に含まれる内容の要旨
Chapter 3- Operation 3.1 Operation SELECTING THE IPOD To select the iPod from the radio, press the button that would normally activate the factory CD changer. This button varies by vehicle manufacturers. In some applications (using config.#8) the PXDP is accessed like an XM reciever, In these cases you will press the appropriate activation button. Some radio models require pressing the “Seek >” button once, after pressing the CD button. Yet, it may also be necessary to press Play on the iPo
ページ10に含まれる内容の要旨
3.2 Trouble Shooting Symptom Cause Remedy No Power Blown fuse in vehicle fuse Replace fuse with same block. amp rating. If the fuse blows again, call tech support. No Power Bad connection Check cable and wiring connection. Alternator noise is heard Improper wiring creates a Install a Ground loop isola- (Changes with Engine RPM) ground loop tor or seek professional service from a local car audio shop. You can hear music from The Firmware on the iPod Update the Firmware on the iPod but you
ページ11に含まれる内容の要旨
3.3 Warranty One Year Limited Warranty The quality controls used in the manufacture of this product will ensure your satisfaction. This warranty applies only to the original purchaser of this product from an authorized Peripheral Elecronics dealer. This warranty covers any supplied or manufactured parts of this product that, upon inspec- tion by Peripheral Electronics authorized personnel, is found to have failed in normal use due to defects in material or workmanship. This warranty does not
ページ12に含まれる内容の要旨
www.peripheralelectronics.com Peripheral Electronics®, a division of AAMP of America™ 13160 56th Court Clearwater, Florida 33760 866-788-4237 in the US or 727-572-9255 ext.262 for international calls support@peripheralelectronics.com ©2006 AAMP™ of Florida, Inc.
