ページ1に含まれる内容の要旨
Design for Manufacturing and Environment Document
Firebox V10
De-manufacturing
Instructions
Document Number: 480-2524-001
WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 1 of 10
Authorization and Revision History for this document is available in the WatchGuard ECO system
ページ2に含まれる内容の要旨
Design for Manufacturing and Environment Document 1.0 Purpose This instruction defines the de-manufacturing process for the recovery of this product family as it pertains to recycling of the major product components. 2.0 Scope This instruction applies to the following product family and family part numbers. Product Family Name Family part #’s (not necessarily inclusive) Firebox V10 • Firebox V10; all revisions WatchGuard Technologies.
ページ3に含まれる内容の要旨
Design for Manufacturing and Environment Document 3.0 Instruction 3.1 -Remove labels, rubber feet and screws Material removed (part Instruction visual Desc or P/N & material type) Labels Cert. label: 0791-00x– Metalized poly-film Warranty void: 0230-001 - Poly-film Remove rubber feet Serial number: 0812-00x - Poly-film Remove labels Product UPC: 0813-00x - Poly-film Rubber Feet 0428-002 - PSA clear; 4 ea.
ページ4に含まれる内容の要旨
Design for Manufacturing and Environment Document Material removed (part Instruction visual Desc or P/N & material type) Upper housing 0788-001- PC/ABS FR110 Disengage press fit display from upper housing with fingers Disconnect display module by lifting corner locks and pulling display flex circuit 3.3 –Disassemble display module WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 4 of 10 A
ページ5に含まれる内容の要旨
Design for Manufacturing and Environment Document Material removed (part Instruction visual Desc or P/N & material type) Flex Circuit 0784-001- Flex PCBA with SC42 Neoprene backing Lens Components Lens front 0781-001- Polycarbonate Lightpipe 0782-001- Polycarbonate Pull flex circuit with backing from display lens WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 5 of 10 A
ページ6に含まれる内容の要旨
Design for Manufacturing and Environment Document 3.4 –Remove Connector Hex Head Standoffs and separate PCBA Assembly from Lower Housing Material removed (P/N Instruction visual & material type) Stand-offs xxxx-0xx – Hex-head stainless steel; 2 ea. Remove standoffs -2 ea. Lower housing Separate PCBA from 0789-001- PC/ABS FR110 lower housing 3.2 –Disconnect PCBA Posts and Remove from Interconnect PCBA WatchGuard Technologies.
ページ7に含まれる内容の要旨
Design for Manufacturing and Environment Document Material removed (P/N Instruction visual & material type) Disconnect PCBA from base housing, 5 places Interconnect PCBA 0774-001- PCBA Separate plastic posts Locking posts from Interconnect PCBA, 0778-001- Nylon; 5 ea. 5 ea. WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 7 of 10 Authorization and Revision History for this document
ページ8に含まれる内容の要旨
Design for Manufacturing and Environment Document 3.3 – Remove battery from Main PCBA Material removed (P/N Instruction visual & material type) Battery –coin cell 0301-001– Manganese oxide / Lithium CR2032 Remove Battery from clip WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 8 of 10 Authorization and Revision History for this document is available in the WatchGuard ECO system
ページ9に含まれる内容の要旨
Design for Manufacturing and Environment Document 3.2 –Disconnect PCBA Connector and Separate PCBA, EMI Shield and Base Material removed (P/N Instruction visual & material type) Disconnect PCBA from base housing with pressure with tool or fingers, 2 places Separate PCBA, EMI Main PCBA shield and base housing. 0748-001- PCBA Locking posts 0776-001- Nylon; 2 ea. Base housing 0775-001- PC/ABS FR110 EMI Shield 0775-001- Metalized EMI paper
ページ10に含まれる内容の要旨
Design for Manufacturing and Environment Document 4.0 Applicable Documents 5.0 Revision History REV. REV. DATE REVISED SECTION REASON ECO# NO. A 10/10/2005 n/a Initial Release 0712 WatchGuard Technologies. Doc #480-2524-001 Rev. A Page 10 of 10 Authorization and Revision History for this document is available in the WatchGuard ECO system
