ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
© Copyright 2007 Compex Systems Pte Ltd All Rights Reserved This document contains information, which is protected by copyright. Reproduction, adaptation or translation without prior permission is prohibited, except as allowed under the copyright laws. Trademark Information ® is a registered trademark of Compex, Inc. Microsoft Windows and the Windows logo Compex are the trademarks of Microsoft Corp. NetWare is the registered trademark of Novell Inc. WMM and WPA are the registe
ページ3に含まれる内容の要旨
FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. RF Exposure warning The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any o
ページ4に含まれる内容の要旨
Table of Contents OVERVIEW THE PRODUCT ..............................................................1 Introduction ................................................................................................... 1 Features and Benefits................................................................................... 2 When to Use Which Mode........................................................................... 4 Access Point Mode............................................
ページ5に含まれる内容の要旨
Access the Secure Shell Host Command Line Interface .................. 67 Set the WEB Mode ...................................................................................... 68 Use MAC Filtering........................................................................................ 69 Add a MAC Address to the MAC Address List ................................... 70 Delete a MAC Address from All Access Points................................... 73 Delete a MAC Address from Individu
ページ6に含まれる内容の要旨
Setup 802.1x/RADIUS for Access Point................................................... 131 Setup 802.1x/RADIUS for Client ............................................................... 133 Setup WPA Enterprise for Access Point ................................................. 135 Setup WPA Enterprise for Client.............................................................. 136 CONFIGURE THE SECURITY FEATURES .......................................139 Use Packet Filtering...........
ページ7に含まれる内容の要旨
Overview the Product Introduction NetPassage WPE53G is a high-performance and low-cost IEEE802.11b/g Access Point using the latest AR5007 technology. NetPassage WPE53G is also very small compared to other Access Points in the market. Using Atheros System-on-Chip (SoC) solution, WPE53G supports high-speed data transmission of up to 54Mbps or 108 Mbps. Moreover, Power-over-Ethernet support enables NetPassage WPE53G to be used even in areas without readily-available power outlets.
ページ8に含まれる内容の要旨
Features and Benefits • Compact Form Factor • Compact Form Factor Small in dimension; light in weight. You can bring it with you anywhere. • Multiple-SSID Supporting VLAN Segmentation. • Multiple-SSID Supporting VLAN Segmentation. Up to 4 virtual access points (VAP) with unique BSSIDs is supported and if required, traffic from each VAP can be tagged to a specific VLAN and bridged. The security mode for each VLAN can be configured separately. • Long Range Support • Long Ra
ページ9に含まれる内容の要旨
• • P Pa arra alllle ell B Brro oa ad db ba an nd d In Gateway Mode, Load-Balancing and Fail-Over Redundancy provides scalable Internet bandwidth. • Antenna Control and Alignment • Antenna Control and Alignment Allows the user to select the specific antenna to use, and also adjust it for optimal throughput. • DHCP Relay • DHCP Relay In Routing Mode, DHCP clients can get IP address from the central DHCP server even if they are on different subnets. • • R Re em mo ott
ページ10に含まれる内容の要旨
When to Use Which Mode Access Point Mode The Access Point Mode is the default mode of the access point and enables the bridging of wireless clients to access the wired network infrastructure and also enables their communication with each other. In this example the wireless users are able to access the file server connected to the switch, through the access point in Access Point Mode. Page 4
ページ11に含まれる内容の要旨
Access Point Client Mode In Access Point Client Mode the device acts as a wireless client. When connected to an access point, it creates a network link between the Ethernet network connected at this client device, and the wireless Ethernet network connected at the access point. In this mode it can only connect with another access point. Other wireless clients cannot connect to it directly unless they are also connected to the same access point – allowing them to communicate with a
ページ12に含まれる内容の要旨
Wireless Routing Client Mode In Wireless Routing Client Mode the Ethernet port of the access point may be used to connect with other devices on the network while Internet access would be provided through wireless communication with a wireless ISP. Page 6
ページ13に含まれる内容の要旨
Gateway Mode In Gateway Mode, the access point supports several types of broadband connections in a wireless network after you have identified the type of broadband Internet access you are subscribed to. Page 7
ページ14に含まれる内容の要旨
Broadband Internet Access Type: Static IP Address Use Static IP Address if you have subscribed to a fixed IP address or to a range of fixed IP addresses from your ISP. Dynamic IP Address With Dynamic IP Address the access point requests for, and is automatically assigned an IP address by your ISP, for instance: • Singapore Cable Vision • @HOME Cable Services PPP over Ethernet (PPPoE) Use PPPoE if you are using ADSL services in a country utilizing standard PPPoE authentication
ページ15に含まれる内容の要旨
Wireless Adapter Mode In Wireless Adapter Mode, the access point can communicate wirelessly with another access point to perform transparent bridging between 2 networks, like in the Access Point Client Mode. In this mode, however, the wireless adapter connects to a single workstation only. No client software or drivers are required to use this mode. Optional additional feature: Point-to-Point connection in this operation mode is also supported if you specifically wish to connect w
ページ16に含まれる内容の要旨
Transparent Client Mode In Transparent Client Mode, the access point provides connection with * an access point acting as the RootAP. This operation is designed for the implementation of Point-to-Point and Point-to-Multipoint connections. Point-to-Point Point-to-MultiPoint An access point acts as Root AP and 1 An access point acts as Root AP other access point acts as Transparent and several other access point Client. acts as Transparent Clients. This mode is generally used fo
ページ17に含まれる内容の要旨
Difference Between other client modes and Transparent Client Mode Other client modes Transparent Client Mode Connectivity with any Connectivity with RootAP- standard APs. supported APs. All devices connected to Devices connected to the the Ethernet port use a Ethernet port flow through common MAC address for freely and transparently communications with the without the MAC address AP. restriction. The Transparent Client Mode is more transparent, making it more suitable for link
ページ18に含まれる内容の要旨
Repeater Mode The access point comes with a built-in Repeater Mode to extend the range, and substantially enhance the performance of the wireless network by allowing communications over much greater distances. In Repeater Mode, the access point acts as a relay for network signals on the network by regenerating the signals it receives, and retransmitting them to extend the range of the existing network infrastructure. Detailed information on the Repeater Mode is available in the
ページ19に含まれる内容の要旨
Panel Views and Description Page 13
ページ20に含まれる内容の要旨
Install the Hardware Setup Requirements • CAT5/5e Networking Cable. • At least 1 computer installed with a web browser and a wired or wireless network interface adapter. • All network nodes installed with TCP/IP and properly configured IP address parameters. Using power adapter to supply power to the unit * Caution: LV model DC Jack input voltage range is 9-15VDC HV model DC Jack input voltage range is 15-24VDC *** DO NOT use power adapter from HV mod
