ページ1に含まれる内容の要旨
Foundry IronPoint 250
Installation Guide
4980 Great America Parkway
Santa Clara, CA 95054
Tel 408.207.1700
www.foundrynetworks.com
August 2007
ページ2に含まれる内容の要旨
Copyright © 2007 Foundry Networks, Inc. All rights reserved. No part of this work may be reproduced in any form or by any means – graphic, electronic or mechanical, including photocopying, recording, taping or storage in an information retrieval system – without prior written permission of the copyright owner. The trademarks, logos and service marks ("Marks") displayed herein are the property of Foundry or other third parties. You are not permitted to use these Marks without the prior writte
ページ3に含まれる内容の要旨
Compliances FCC - Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no
ページ4に含まれる内容の要旨
Foundry IronPoint 250 Installation Guide FCC Antenna Usage and Transmit Power To comply with FCC/Canada telecommunication regulation, the conducted output power of this transmitter, when use with each specific antenna supplied, cannot exceed the maximum limit indicated in the following tables. 802.11a RF Power Table for FCC External Antenna Maximum Conducted Transmit Power (dBm) 5180 MHz 5240 MHz 5745 MHz 5785 MHz 5825 MHz 4.5 dBi Integrated Antenna 11.64 14.91 24.6 24.9 25.2 (FDS_2FED02) 8 dB
ページ5に含まれる内容の要旨
Compliances 802.11g RF Power Table for FCC External Antenna Maximum Conducted Transmit Power (dBm) 2412 MHz 2437 MHz 2462 MHz 2 dBi Integrated Antenna 21.1 24.5 17.68 (FDS_2FED02) 6 dBi Omnidirectional Antenna 19.4 24 17.2 (MMO24580608) (not including 1 dBi cable loss) 4 dBi Bi-Directional Antenna 19.4 24 16.7 (MHA2400PT) 13 dBi Directional Panel Antenna 15.6 21.75 11.6 (MP24013XFPT) Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio noise emissions fr
ページ6に含まれる内容の要旨
Foundry IronPoint 250 Installation Guide EC Declaration of Conformity 0560 Contact Foundry Networks at: Foundry Networks, Inc. 4980 Great America Parkway Santa Clara, CA 95054 Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: EN 60950 (IEC 60950) - Product Safety EN 301 893 - Technical requirements for 5 GHz radio equipment EN 300 328 - Technic
ページ7に含まれる内容の要旨
Compliances Operation Using 5 GHz Channels in the European Community The user/installer must use the provided configuration utility to check the current channel of operation and make necessary configuration changes to ensure operation occurs in conformance with European National spectrum usage laws as described below and elsewhere in this document. Allowed 5GHz Channels in Each European Community Country Allowed Frequency Bands Allowed Channel Numbers Countries 5.15 - 5.25* GHz 36, 40, 44, 48
ページ8に含まれる内容の要旨
Foundry IronPoint 250 Installation Guide German Hiermit erklärt Foundry Networks, dass sich dieser/diese/dieses Radio LAN device in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi) Hiermit erklärt Foundry Networks die Übereinstimmung des Gerätes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien) Greek Με την παρουσα Foundry Networks
ページ9に含まれる内容の要旨
Compliances Power Cord Set U.S.A. and Canada The cord set must be UL-approved and CSA certified. The minimum specifications for the flexible cord are: - No. 18 AWG - not longer than 2 meters, or 16 AWG. - Type SV or SJ - 3-conductor The cord set must have a rated current capacity of at least 10 A The attachment plug must be an earth-grounding type with NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration. Denmark The supply plug must comply with Section 107-2-01, Standard DK2-1a o
ページ10に含まれる内容の要旨
Foundry IronPoint 250 Installation Guide Cordon électrique - Il doit être agréé dans le pays d’utilisation Etats-Unis et Canada: Le cordon doit avoir reçu l’homologation des UL et un certificat de la CSA. Les spécifications minimales pour un cable flexible sont AWG No. 18, ou AWG No. 16 pour un cable de longueur inférieure à 2 mètres. - type SV ou SJ - 3 conducteurs Le cordon doit être en mesure d’acheminer un courant nominal d’au moins 10 A. La prise femelle de branchement doit être du type à
ページ11に含まれる内容の要旨
Contents Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii Chapter 1. About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 Nomenclature . . . . . . . . . . .
ページ12に含まれる内容の要旨
Foundry IronPoint 250 Installation Guide Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7 Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7 Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7 Chapter 3. Network Planning
ページ13に含まれる内容の要旨
Contents Crossover Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 Console Port Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Wiring Map for Serial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Appendix C. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ14に含まれる内容の要旨
Foundry IronPoint 250 Installation Guide xiv © 2007 Foundry Networks, Inc. August 2007
ページ15に含まれる内容の要旨
Chapter 1 About This Guide The IronPoint™ 250 Access Point is a device that allows wireless clients to connect to your enterprise network. It is a full-featured access point that can be managed as a single device. This guide presents the procedures for installing the IronPoint™ 250 Access Point. Audience This guide is for system administrators with a working knowledge of wireless networks and network management. You should be familiar with switching and networking concepts. Nomenclature Th
ページ16に含まれる内容の要旨
Foundry IronPoint 250 Installation Guide Web Access Point your browser to the kp.foundrynet.com to access the Foundry Knowledge Portal. Note: Check with your sales account representative to determine how to obtain a valid user name and password for the Foundry Knowledge Portal. E-mail Access Technical requests can also be sent to the e-mail address: support@foundrynet.com Telephone Access ◆ 1.877.TURBOCALL (887.2622): United States ◆ 1.408.586.1881: Outside the United States Warranty Coverag
ページ17に含まれる内容の要旨
Chapter 2 About the IronPoint 250 Overview Foundry’s IronPoint 250 is an IEEE 802.11a/g enterprise wireless access point that provides high- speed data communications between the wired LAN and fixed, portable or mobile devices equipped with an 802.11a, 802.11b, or 802.11g wireless network card. The access point offers full network management capabilities through a command line interface for initial configuration and troubleshooting, a Web interface, and Simple Network Management tools. Figure
ページ18に含まれる内容の要旨
Foundry IronPoint 250 Installation Guide Radio Characteristics The IEEE 802.11a/g standard uses a radio modulation technique known as Orthogonal Frequency Division Multiplexing (OFDM), and a shared collision domain (CSMA/CA). It operates at the 5 GHz Unlicensed National Information Infrastructure (UNII) band for connections to 802.11a clients, and at 2.4 GHz for connections to 802.11g clients. IEEE 802.11g includes backward compatibility with the IEEE 802.11b standard. IEEE 802.11b also oper
ページ19に含まれる内容の要旨
About the IronPoint 250 Description of Hardware Ethernet Port The access point has one 10BASE-T/100BASE-TX RJ-45 Ethernet port that can be attached directly to a 10BASE-T/100BASE-TX/1000BASE-T wired network. The wired network must conform to the IEEE 802.3-2005 specifications. The Ethernet port supports automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs, switches, or hubs. The access point appears as an Ethernet node and performs a bridgin
ページ20に含まれる内容の要旨
Foundry IronPoint 250 Installation Guide Figure 2-2. An Example of an Optional External Antenna 2-4 © 2007 Foundry Networks, Inc. August 2007
