ページ1に含まれる内容の要旨
Magnum DX40
Serial Device Router
Installation Guide
GarrettCom Utility Networks
25 Commerce Way #1
North Andover, MA 01845
Phone: 978.688.8807
Fax: 978.688.8771
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Declarations DOCUMENT NOTICE Copyright Copyright 2007 by GarrettCom. Printed in the US. All rights reserved. This manual may not be reproduced or disclosed in whole or in part by any means without the written consent of GarrettCom. DynaStar is a trademark of Garrett. All other trademarks mentioned in this document are the property of their respective owners. This document has been prepared to assist users of equipment manufactured by GarrettCom and changes are made periodically to the informa
ページ4に含まれる内容の要旨
Warranty Revision History Document Software Release Date Change Note Revision Release October, 2006 01 1.1 New product release, Hardware and Software January, 2007 02 1.2 New product release, Hardware and Software February, 2007 AA 1.2 New product release, Hardware and Software June, 2007 AB 1.3 Added dimensional drawings, minor edits. WARRANTY GarrettCom warrants equipment manufactured by it to be free from defects in materials and workmanship for a period of one (1) year from date of ship
ページ5に含まれる内容の要旨
Patents PATENTS As to equipment proposed and furnished by GarrettCom, GarrettCom shall defend any suit or proceeding brought against purchaser so far as based on a claim that said equipment constitutes an infringement of any patent of the United States, if notified promptly in writing and given authority, information, and assistance at GarrettCom's expense for the defense of the claim. In event of a final award of costs and damages from such a suit, GarrettCom shall pay such award. In event
ページ6に含まれる内容の要旨
Safety IC CS03 (Industry Canada) This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the interference-causing equipment entitled “Digital Apparatus”, ICES-003 of the department of Communications (Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques”, NMB-003 édictée par le ministre des Commu
ページ7に含まれる内容の要旨
Contacting GarrettCom Utility Networks Service Personnel Warning The DX40 may be AC or DC powered. Remove all power connections at the circuit panel before removing the unit. The installation of this product must comply with all applicable codes and practices specified by the country, city, and operating company in which it is installed. Grounding All units requiring grounding. Use a grounding wire with a minimum size of 14 AWG at a maximum length of five feet. The DX40 is equipped with an ex
ページ8に含まれる内容の要旨
Contacting GarrettCom Utility Networks DX40 Serial Device Router Installation Guide vi
ページ9に含まれる内容の要旨
TABLE OF CONTENTS Preface About This Manual ............................................................................................................................ ix Conventions ...................................................................................................................................... ix Related Documents........................................................................................................................... ix Web Access .......................
ページ10に含まれる内容の要旨
CONTENTS 2.3.3 Connecting Network Cables ...............................................................................................18 2.3.3.1 Connecting Serial Cables ......................................................................................18 2.3.3.2 Connecting Ethernet Copper Cables .....................................................................18 2.3.3.3 Connecting Fiber Ethernet Cables ........................................................................19 2.4 Maint
ページ11に含まれる内容の要旨
Preface ABOUT THIS MANUAL This document provides instructions for installing the Magnum DX40 hardware. This document gives product descriptions, specifications, detailed information on ports and pinouts, all site preparation required to install the product, complete installation procedures, power up instructions, and instructions for removing and maintaining the product. This document is arranged as follows: Chapter 1, “Overview” - Contains a brief product description, a list of applicable
ページ12に含まれる内容の要旨
- WEB ACCESS All of the DX40 manuals are also available in .pdf format on the GarrettCom Utility Networks website, www.garrettcomun.com. YOUR COMMENTS If you find an error or have a helpful tip on the layout or informational content of this or any other GarrettCom Utility Networks manual please feel free to contact us via email with any problems or helpful information. All enquiries will be responded to with a correction or whatever resolution is required. Please make all comments to supp
ページ13に含まれる内容の要旨
Chapter 1 Overview 1.1 Overview The Magnum DX40 provides connectivity to asynchronous and Ethernet traffic through two programmable serial ports and two Ethernet ports for Fiber optic and (optionally) copper line connections. 1.2 Configuration The following sections describe the features and requirements of the DX40. 1.2.1 Connectivity Depending on the DX40 Model ordered, the DX40 is equipped with: • 2 Ethernet ports, either 2 100FX multi/single mode SFP or One 100FX multi/single mode SFP and
ページ14に含まれる内容の要旨
CHAPTER 1 - Overview Configuration 1.2.2 Power and Ground The DX40 can be ordered with a high (90 -250 VAC or VDC) or low (24-48 VDC) voltage power supply. The connection point for the power supply is located at the top of the chassis. The top surface also contains the primary ground stud and labels including serial number, model number, and power specifications, as illustrated in Figure 1-2. For detailed power specifications see Table 1-5. Ground Connection 2-position Terminal Block Power Co
ページ15に含まれる内容の要旨
CHAPTER 1 - Overview Configuration Power Activity LEDs Ethernet Ports Serial Ports Figure 1-3. Side View 1.2.4 Mounting Options There are two mounting options for the DX40: • Panel mount (see Section 2.3.1.1) • DIN rail mount (see Section 2.3.1.2) Each of these options requires specific accessory hardware. A DX40 intended for panel mounting is delivered with a pair of panel mounting brackets that fasten to screw holes in the DX40 as illustrated in Figure 2-2. A DX40 intended for DIN rail mount
ページ16に含まれる内容の要旨
CHAPTER 1 - Overview Specifications 1.3 Specifications The following sections provide detailed information about the physical, electronic, and industrial specifications of the DX40. 1.3.1 Physical The physical dimensions and weight of the DX40 are defined in Table 1-1. Table 1-1. Physical Specifications • Chassis only – 5.125 inches (13cm) Height: • Chassis + top and bottom connectors – 6.125 inches (16.56cm) Width: 5.125 inches (13cm) 2.125 inches (5.4cm) Depth: 3.5 lbs (1.5 kg) Weight: 1.3.2
ページ17に含まれる内容の要旨
CHAPTER 1 - Overview Specifications 1.3.4 Compliance The industry compliance profile of the DX40 is defined in table Table 1-4. Table 1-4. Compliance With Standards IEEE 1613, IEC 61850-3 Industrial: EN55022A, FCC Part 15A Emissions: Immunity: EN55024 EN61000-4-6 (CRF) EN61000-6-2 EN61000-4-10 (MagField) EN61000-6-5 EN61000-4-11 (VDI) EN61000-4-2 (ESD) EN61000-4-12 (Oscillatory) EN61000-4-3 (RF) EN61000-4-16 (CCM) EN61000-4-4 (EFT) EN61000-4-17 (Ripple) EN61000-4-5 (SURGE) EN61000-4-29 (VDI) UL6
ページ18に含まれる内容の要旨
CHAPTER 1 - Overview Specifications 1.3.6 Ports and External Connectors The ports and external connectors of the DX40 are defined in Table 1-6. Table 1-6. Ports and External Connectors Port Name Connector Description LC 2 100FX multi/single mode small-format pluggables Ethernet, E1 and E2 (SFP) port for fiber optic Ethernet-capable devices or or Networks, or one 100FX SFP port and one 10/100 LC + RJ45 Mbps Ethernet port for connection to copper Ethernet-capable devices. DB9, female Connectio
ページ19に含まれる内容の要旨
CHAPTER 1 - Overview Pinouts 1.4 Pinouts The following subsections describe the pinouts of the connectors used with the DX40. 1.4.1 RJ45 Table 1-8 defines the pinout of the RJ45 connector used with the DX40. RJ45 connectors can be used on one of the Ethernet ports for 10/100 BaseT connections to copper Ethernet-capable devices. Table 1-8. RJ45 Pinout Pin Signal 1 Tx + 2 Tx - 3 Rx + Pin 1 Pin 8 4 not used 5 not used 6 Rx - E2 7 not used 8 not used 1.4.2 SFP Table 1-9 defines the pinout of the S
ページ20に含まれる内容の要旨
CHAPTER 1 - Overview Pinouts 1.4.3 DB9 (Female) – RS232 Serial Ports Table 1-10 defines the pinout of the DB9 female connector used with serial ports on the DX40 when they are configured for the RS232 interface. DB9 connectors are used on serial ports S1 and S2 for asynchronous or bit-oriented connections. Table 1-10. DB9 RS232 Pinout 6 8 9 7 Pin Name Dir. Description S1/S2 S1/S 2 1 3 4 5 1 DCD In Data Carrier Detect from DCE. 2 RXD In Receive Data from DCE. 3 TXD Out Transmit Data to DCE. 4
